Linksys WAP300N User manual

User Guide
Linksys WAP300N

i
Contents
Linksys WAP300N
i
Overview
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Back view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Setting Up: Basics
How to expand your home network . . . . . . . . . . . . . . . . . .3
What is a network? 3
How to expand your home network 3
Where to nd more help . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Access Point Mode 4
Wireless Media Connector mode 5
Wireless Range Extender mode 6
Wireless Bridge mode 7
How to install your WAP300N. . . . . . . . . . . . . . . . . . . . . . .8
How to open the browser-based utility . . . . . . . . . . . . . . . .8
How to use Access Point mode . . . . . . . . . . . . . . . . . . . . . .9
How to select Access Point mode 9
How to use Wi-Fi Protected Setup 9
How to manually set up your WAP300N 10
How to set up wireless security 11
How to use Wireless Media Connector mode . . . . . . . . . . . . 12
How to select Wireless Media Connector mode 12
How to run a wireless network site survey 12
How to use Wi-Fi Protected Setup 13
How to manually set up your WAP300N 14
How to use Wireless Range Extender mode . . . . . . . . . . . . . 15
How to select Wireless Range Extender mode 15
How to run a wireless network site survey 16
How to use Wi-Fi Protected Setup 16
How to manually set up your WAP300N 16
How to use Wireless Bridge mode . . . . . . . . . . . . . . . . . . . 16
How to select Wireless Bridge mode 16
How to set up Wireless Bridge Mode 17
How to set up wireless security 18
Setting Up: Advanced
How to set up the MAC lter . . . . . . . . . . . . . . . . . . . . . . 19
How to set up QoS (Quality of Service) . . . . . . . . . . . . . . . . 20
How to change the IP address . . . . . . . . . . . . . . . . . . . . . 20
How to change the password. . . . . . . . . . . . . . . . . . . . . . 21
How to change the idle timeout . . . . . . . . . . . . . . . . . . . . 21
How to disable wireless admin access . . . . . . . . . . . . . . . . 21
How to change the browser-based utility’s language. . . . . . . 21
Maintaining and Monitoring
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
How to back up and restore your WAP300N conguration . . . 22
How to reboot your WAP300N . . . . . . . . . . . . . . . . . . . . . 22
How to restore your WAP300N’s factory settings. . . . . . . . . . 23
How to update your WAP300N . . . . . . . . . . . . . . . . . . . . . 23
How to view device and local network information. . . . . . . . 24
How to view wireless network information . . . . . . . . . . . . . 24
Contents

ii
Contents
Linksys WAP300N
Specications
Linksys WAP300N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Environmental 26

1
Overview
Linksys WAP300N
1
Overview
Package contents
In addition to your device, the package includes:
•Quick Installation Guide
•Network (Ethernet) cable
•AC power adapter
•Setup CD containing setup software and documentation
•Detachable antennas (2)
Back view
Ethernet port and activity indicator
Antennas
Wi-Fi Protected Setup button
and indicator
Wireless activity indicator Power port and indicator
•Antenna connector—For connecting the included antennas.
•Wireless activity indicator—In Access Point mode, it lights up solid
when the wireless interface is ready. In other modes, it lights up solid
when the WAP300N connected to a router, access point, or another
WAP300N. Flashes while actively sending or receiving data over a
wireless connection.
• Wi-Fi Protected Setup™ button—Press this button to easily set up a
wireless connection.
•Wi-Fi Protected Setup indicator—Stays on steadily following a
successful Wi-Fi Protected Setup connection or when wireless security
is enabled. Flashes slowly during Wi-Fi Protected Setup. Flashes quickly
when there is a Wi-Fi Protected Setup error.
•Ethernet port—Connect a wired network device to this port.
•Ethernet activity indicator—Lights up when there is a wired connection.
Flashes while actively sending or receiving data over the Ethernet port.
•Power port—Connect the included AC power adapter to this port.
CAUTION
Use only the adapter that came with your router.
•Power indicator—Stays on steadily while power is connected. Flashes
slowly during bootup, firmware upgrades, and factory reset.

2
Overview
Linksys WAP300N
Bottom view
•Reset button—Press and hold this button for 5 seconds to reset the
device to its factory defaults.

3
Setting Up: Basics
Linksys WAP300N
3
How to expand your home network
What is a network?
A network is any group of devices that can communicate with each other. A
typical home network may include multiple computers, a printer, a modem (for
Internet access), and a router. A large home network may also have a switch,
additional routers, access points, and many Internet-capable media devices
such as TVs, game consoles, and web cameras.
How to expand your home network
Your WAP300N provides several ways to increase your home network’s
capabilities and wireless range. You can use it as any of the following:
• Access Point mode (default)
• Wireless Media Connector mode
• Wireless Range Extender mode
• Wireless Bridge mode
Refer to the following pages for more detailed explanations and example
diagrams.
Where to find more help
In addition to this User Guide, you can also find help at Linksys.com/support
(documentation, downloads, FAQs, technical support, live chat, forums).
Setting Up: Basics

4
Setting Up: Basics
Linksys WAP300N
Access Point Mode
Adds wireless networking to an existing wired (Ethernet) network or upgrades an existing
wireless network. For instructions about using this mode, see “How to use Access Point
mode” on page 9.
• If you have a wired network, this mode adds the ability to connect wireless devices
(such as notebook computers, tablets, and smartphones) to the network.
• If you have an older wireless network, this mode adds Wireless-N (802.11n)
networking support.
• If you have a Wireless-N (802.11n) 2.4 GHz-only network, this mode adds support for
the 5 GHz band.
Operating modes
Internet Modem Router
Notebook
Computer
Tablet
Smartphone
WAP300N

5
Setting Up: Basics
Linksys WAP300N
Wireless Media Connector mode
Adds wireless networking capability to any wired (Ethernet) device. For instructions
about using this mode, see “How to use Wireless Media Connector mode” on page 12.
Ethernet-Capable
Game Console
WAP300N
Internet Modem Wireless
Router

6
Setting Up: Basics
Linksys WAP300N
Wireless Range Extender mode
Extends the wireless range of an existing wireless network, and also adds wireless
networking capability to any wired (Ethernet) device. For instructions about using this
mode, see “How to use Wireless Range Extender mode” on page 15.
WAP300N
Internet Modem Wireless
Router
Ethernet-Capable Game Console
Notebook
computer
Tablet

7
Setting Up: Basics
Linksys WAP300N
Wireless Bridge mode
Wirelessly connects separate wired networks. For instructions about using this
mode, see “How to use Wireless Bridge mode” on page 16.
NOTE
Each wired network must be connected
to its own WAP300N (in Wireless Bridge
mode), and each WAP300N must have
identical wireless settings.
Internet Modem Router Network
Printer
Ethernet
Switch
Ethernet
Switch Ethernet Switch
WAP300N
WAP300NWAP300N

8
Setting Up: Basics
Linksys WAP300N
How to install your WAP300N
The easiest way to install your WAP300N is to use the included Setup CD.
NOTE
The Setup CD can only help you set up the WAP300N in Access
Point mode. For more information and examples of other modes,
see the diagrams on pages 4 to 7.
To install your WAP300N:
1. Insert the CD into your CD or DVD drive. Make sure that the computer is
already connected to your home network.
2. Click Set up your wireless access point.
If you do not see this:
For Windows, find and click Computer, then double-click the CD drive
and the Setup icon.
For Mac, double-click the CD icon on your desktop, then double-click the
Setup icon.
3. Follow the on-screen instructions.
How to open the browser-based utility
For advanced configuration of the WAP300N, you need to open the browser-
based utility.
To open the browser-based utility:
1. Connect the WAP300N to your network. For example, use the included
cable to connect your WAP300N to the Ethernet port on your network
router or a networked computer.
2. Open a web browser on a computer connected to your network, then
enter the IP address of your WAP300N. You are prompted for a user name
and password.
TIPS
• If the WAP300N is connected to a network with a DHCP server
(usually the network router), find the device’s IP address in
the DHCP client table of your router (refer to your router’s
documentation for help). Use that IP address to open the
browser-based utility.
• If there is no DHCP server, or if the WAP300N is not wirelessly
connected to any other device and it is connected with an
Ethernet cable directly to a computer, then the WAP300N uses
10.100.1.1 as its IP address until a DHCP server is detected.
• If you set a static IP address for the WAP300N through the
browser-based utility, then enter the static IP address instead.
3. Leave the User name field blank, then type the password you created
during Setup. If you did not create a new password, use the default
password admin.
4. Click OK. The main menu opens.

9
Setting Up: Basics
Linksys WAP300N
How to use Access Point mode
In addition to the topics below, see the topics “How to set up the MAC filter” on
page 19 and “How to set up QoS (Quality of Service)” on page 20.
How to select Access Point mode
To select Access Point mode:
Setup > Operation Mode
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Setup tab, then click the Operation Mode page.
3. Select Access Point (default), then click Save Settings.
How to use Wi-Fi Protected Setup
While in Access Point mode, you can use Wi-Fi Protected Setup™ to easily
connect wireless network devices to your wireless network.
You can use three methods for Wi-Fi Protected Setup:
• Press the Wi-Fi Protected Setup button on each device
• Enter the client device’s Wi-Fi Protected Setup PIN onto the WAP300N
• Enter the WAP300N’s Wi-Fi Protected Setup PIN onto the client device.
To manually configure your network, see “How to manually set up your
WAP300N” on page 10).
NOTE
Your WAP300N must have Wi-Fi Protected Setup enabled before
you can use it to connect network devices. In the browser-based
utility, click the Wireless tab, then click the Basic Wireless Settings
page and make sure that Wi-Fi Protected Setup is set to Enabled.
How to connect a device using the Wi-Fi Protected Setup
button
Use this method if your device has a Wi-Fi Protected Setup button or prompts
you to press the Wi-Fi Protected Setup button on your WAP300N .
To connect a device using the Wi-Fi Protected Setup button:
1. Press the Wi-Fi Protected Setup button on the network device you are
connecting to.
2. Within two minutes, press the Wi-Fi Protected Setup button on the
back of the WAP300N.
- OR -
a. Log into the WAP300N’s browser-based utility (see “How to open the
browser-based utility” on page 8).
b. Click the Wireless tab, then click the Basic Wireless Settings page.
c. For Configuration View, select Wi-Fi Protected Setup™.
d. Click the Wi-Fi Protected Setup button in the Wi-Fi Protected Setup
screen.

10
Setting Up: Basics
Linksys WAP300N
How to connect a device using its Wi-Fi Protected Setup PIN
Use this method if your device has a Wi-Fi Protected Setup PIN (Personal
Identification Number).
To connect a device using the device’s Wi-Fi Protected Setup PIN:
Wireless > Basic Wireless Settings
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Basic Wireless Settings page.
3. For Configuration View, select Wi-Fi Protected Setup™.
4. Enter the PIN from the device into the PIN field on the WAP300N’s Wi-Fi
Protected Setup screen, then click Register.
The Wi-Fi Protected Setup status, wireless band, network name (SSID),
and security mode are displayed at the bottom of the screen.
How to connect a device using the WAP300N’s Wi-Fi Protected
Setup PIN
Use this method if your client device asks for the WAP300N’s PIN (Personal
Identification Number).
To connect a device using the WAP300N’s Wi-Fi Protected Setup PIN:
Wireless > Basic Wireless Settings
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Basic Wireless Settings page.
3. For Configuration View, select Wi-Fi Protected Setup™.
4. On the client device, enter the PIN listed on the WAP300N’s Wi-Fi
Protected Setup screen. It is also listed on the bottom of the WAP300N. In
the example below, the WAP300N’s PIN is 32744781.
The Wi-Fi Protected Setup status, wireless band, network name (SSID),
and security mode are displayed at the bottom of the screen.
How to manually set up your WAP300N
To manually set up your access point:
Wireless > Basic Wireless Settings
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Basic Wireless Settings page.
3. For Configuration View, select Manual.

11
Setting Up: Basics
Linksys WAP300N
4. Configure the following fields:
Wireless Band—Select the 2.4 GHz or 5 GHz radio band. The 5GHz band
is much less crowded than the 2.4 GHz band, so it is more likely to be
free from interference. Although the 5 GHz band is ideal for streaming
multimedia, not all wireless client devices support the 5GHz radio band.
Network Mode (5 GHz)—Select your network’s wireless standard. If you
have both Wireless-N (802.11n) and Wireless-A (802.11a) devices in your
network, keep the default setting, Mixed. If you have only Wireless-N
devices in your network, select Wireless-N Only. If you have only
Wireless-A devices in your network, select Wireless-A Only.
Network Mode (2.4 GHz)—Select your network’s wireless standard.
If you have Wireless-N (802.11n), Wireless-G (802.11g), and Wireless-B
(802.11b) devices in your network, keep the default, Mixed. If you
have only Wireless-N devices, select Wireless-N Only. If you have only
Wireless-G and Wireless-B devices in your network, select Wireless-B/G
Only. If you have only Wireless-G devices, select Wireless-G Only. If you
have only Wireless-B devices, select Wireless-B Only.
Network Name (SSID)—The SSID is the name of your wireless network.
This network name is shared among all the wireless devices connected
to your wireless network. The SSID is case-sensitive.
Channel Width—For best performance in a Wireless-N network, select
40MHz only (available only in the 5GHz radio band) or Auto. In Auto
mode, the WAP300N and the network client devices automatically switch
to the 40 MHz mode if:
• Your wireless client devices support the 40 MHz mode in which two
20MHz channels are bonded together for better performance.
and
• There is no adjacent interference.
Channel—Select the operating channel for your wireless network. Your
WAP300N will automatically select the channel with the least amount
of interference if you leave the default Auto setting. We recommend
keeping the default (Auto).
SSID Broadcast—Select Enabled (default) to allow wireless client
devices to “see” the wireless network name. If you do not want to
broadcast the WAP300N’s SSID, select Disabled. We recommend keeping
the default setting (Enabled).
5. Click Save Settings.
How to set up wireless security
To set up wireless security for your WAP300N in Access Point mode:
Wireless > Wireless Security
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Wireless Security page and select
the Security Mode. (We recommend WPA2 Personal for most home
networks.)
Depending on the security mode you selected, you may be asked to
enter additional information (see the following table).
Security mode
Information
Required Description
WPA2/WPA
Mixed Mode,
WPA2 Personal,
WPA Personal
Passphrase
Enter the passphrase of 8-63 characters.
WPA2/WPA
Enterprise
Mixed
Mode, WPA2
Enterprise,
WPA Enterprise
RADIUS Server Enter the IP address of the RADIUS server.
RADIUS Port Enter the port number of the RADIUS
server. The default is 1812.
Shared Key
Enter the key shared between the router
and the server.
WEP
Encryption
Select a level of WEP encryption, 40/64-
bit (10 hex digits) or 104/128-bit (26 hex
digits).
Key 1 Enter the WEP key of your network. Key
1 is the transmit key used by this device.

12
Setting Up: Basics
Linksys WAP300N
RADIUS
RADIUS Server Enter the IP address of the RADIUS server.
RADIUS Port Enter the port number of the RADIUS
server. The default is 1812.
Shared Key Enter the key shared between the router
and the server.
Encryption
Select a level of WEP encryption, 40/64-
bit (10 hex digits) or 104/128-bit (26 hex
digits).
Key 2 Enter the WEP key of your network. Key
2 is the transmit key used by this device.
3. After you have entered all required information, click Save Settings.
How to use Wireless Media Connector
mode
In addition to the topics below, see the topic “How to set up QoS (Quality of
Service)” on page 20.
How to select Wireless Media Connector mode
To select Wireless Media Connector mode:
Setup > Operation Mode
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Setup tab, then click the Operation Mode page.
3. Select Wireless Media Connector, then click Save Settings.
We recommend using wireless network site survey to set up your
WAP300N in Wireless Media Connector mode. Wireless network site
survey identifies wireless networks with in the range of your WAP300N,
so that you can easily select one of them to connect to. For instructions,
see How to run a wireless network site survey below.
How to run a wireless network site survey
We recommend using wireless network site survey to set up your WAP300N
in Wireless Media Connector mode. Wireless network site survey identifies
wireless networks within range of your WAP300N, so that you can easily select
one of them to connect to.
To run a wireless network site survey:
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Wireless Network Site Survey
page. The site survey runs and displays the following information:

13
Setting Up: Basics
Linksys WAP300N
Number of Wireless Networks—The number of wireless networks that
were detected.
Wireless Network Name—The network name (SSID) of each discovered
wireless network.
Signal—The percentage of signal strength.
Security—The security method used by each wireless network. If the
network supports Wi-Fi Protected Setup, the Wi-Fi Protected Setup icon
appears next to the security method.
Refresh—Updates the on-screen information.
3. To connect to a wireless network, select the network, then click Connect.
A screen opens that shows you the network name (SSID) and security
mode of the selected wireless network. Depending on the security mode
of the network, you may be asked to enter additional information (see
the following table).
Security mode
Information
Required Description
WPA/WPA2
Personal Passphrase
Enter the passphrase shared by this
device and your wireless router (or
access point).
WEP
Encryption
Select a level of WEP encryption, 40 /
64-bit (10 hex digits) or 104 / 128-bit
(26 hex digits).
Key 1
Enter the WEP key of your network.
Key 1 is the transmit key used by this
device.
Authentication
The default is Auto, which allows
either open system or shared
key authentication to be used.
Select Open to use open system
authentication (a WEP key is not used
for authentication). Select Shared to
use shared key authentication (a WEP
key is used for authentication).
4. After you have entered all required information, click Connect to connect
to the network.
How to use Wi-Fi Protected Setup
If your wireless router or access point supports Wi-Fi Protected Setup, you can
use it to easily connect your WAP300N to your wireless router or access point.
You can use two methods for Wi-Fi Protected Setup:
• Press the Wi-Fi Protected Setup button on each device
• Enter the WAP300N’s Wi-Fi Protected Setup PIN onto the router or access
point.
To manually configure your network, see “How to manually set up your
WAP300N” on page 14).
How to connect to a router or access point using the Wi-Fi
Protected Setup button
Use this method to connect your WAP300N to a router or access point by
pressing buttons on the two devices.
To connect to your router or access point using the Wi-Fi Protected
Setup button:
1. Press the Wi-Fi Protected Setup button on the back of the router or
access point.
2. Within two minutes, press the Wi-Fi Protected Setup button on the
back of the WAP300N.

14
Setting Up: Basics
Linksys WAP300N
- OR -
a. Log into the WAP300N’s browser-based utility (see “How to open the
browser-based utility” on page 8).
b. Click the Wireless tab, then click the Basic Wireless Settings page.
c. For Configuration View, select Wi-Fi Protected Setup™.
d. Click the Wi-Fi Protected Setup button in the Wi-Fi Protected Setup
screen.
How to connect to a router or access point using the
WAP300N’s Wi-Fi Protected Setup PIN
Use this method if your router or access point asks for the WAP300N’s PIN
(Personal Identification Number).
To connect a device using the WAP300N’s Wi-Fi Protected SetupPIN:
Wireless > Basic Wireless Settings
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Basic Wireless Settings page.
3. For Configuration View, select Wi-Fi Protected Setup™.
4. On the router or access point’s browser-based utility, enter the PIN listed
on the WAP300N’s Wi-Fi Protected Setup screen. It is also listed on the
bottom of the WAP300N. In the example below, the WAP300N’s PIN is
02743103.
The Wi-Fi Protected Setup status, wireless band, network name (SSID),
and security mode are displayed at the bottom of the screen.
5. Click OK on the WAP300N’s Wi-Fi Protected Setup screen.
How to manually set up your WAP300N
You can follow these instructions to connect your WAP300N to your router, or
you can use Wireless Network Site Survey to connect. For more information
about site survey, see “How to run a wireless network site survey” on page 12.
To manually set up your WAP300N in wireless media connector mode:
Wireless > Basic Wireless Settings
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Basic Wireless Settings page.
3. For Configuration View, select Manual.
4. Configure the following fields:
Network Name (SSID)—The SSID is the name of your wireless network.
This network name is shared among all the wireless devices connected
to your wireless network, so the SSID you enter here must match the
router’s SSID exactly (the SSID is case-sensitive).
Security Mode—Select the security mode that matches the security
setting on your router or access point. If the setting here does not match
the setting on your router or access point, it will not be able to connect.

15
Setting Up: Basics
Linksys WAP300N
Depending on the security mode you select, you may be asked to enter
additional information. Refer to the following table.
Security mode
Information
Required Description
WPA/WPA2
Personal Passphrase
Enter the passphrase shared by this
device and your wireless router (or
access point).
WEP
Encryption
Select a level of WEP encryption, 40 /
64-bit (10 hex digits) or 104 / 128-bit
(26 hex digits).
Key 1
Enter the WEP key of your network.
Key 1 is the transmit key used by this
device.
Authentication
The default is Auto, which allows
either open system or shared
key authentication to be used.
Select Open to use open system
authentication (a WEP key is not used
for authentication). Select Shared to
use shared key authentication (a WEP
key is used for authentication).
5. Click Save Settings.
How to use Wireless Range Extender
mode
How to select Wireless Range Extender mode
To select Wireless Range Extender mode:
Setup > Operation Mode
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Setup tab, then click the Operation Mode page.
3. Select Wireless Range Extender, then click Save Settings.

16
Setting Up: Basics
Linksys WAP300N
How to run a wireless network site survey
We recommend using wireless network site survey to set up your WAP300N
in Wireless Range Extender mode. For instructions on using wireless network
site survey to connect your WAP300N to a wireless router, see “How to run a
wireless network site survey” on page12).
How to use Wi-Fi Protected Setup
While in Range Extender mode, you can use Wi-Fi Protected Setup™ to easily
connect your WAP300N to your wireless router and wireless client devices. The
way you use Wi-Fi Protected Setup for your WAP300N varies, depending on
whether your WAP300N has already connected to the router.
If your WAP300N has not yet connected to a router:
• To connect your WAP300N to a wireless router, follow the instructions in
“How to use Wi-Fi Protected Setup” on page13.
If your WAP300N has already connected to a router:
• To connect your WAP300N to a wireless client device, follow the
instructions in “How to use Wi-Fi Protected Setup” on page9.
How to manually set up your WAP300N
You can manually set up your WAP300N’s connection to a wireless router, or
you can change its existing connection to a wireless router.
If your WAP300N has not yet connected to a router:
• Follow the instructions in “How to manually set up your WAP300N” on
page 14).
If your WAP300N has already connected to a router:
1. Refer to “How to manually set up your WAP300N” on page 14) for
information on the menu’s fields.
2. To connect to a different router, change the field values, then click Save
Settings.
How to use Wireless Bridge mode
How to select Wireless Bridge mode
To select Wireless Bridge mode:
Setup > Operation Mode
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Setup tab, then click the Operation Mode page.
3. Select Wireless Bridge, then click Save Settings.

17
Setting Up: Basics
Linksys WAP300N
How to set up Wireless Bridge Mode
To set up Wireless Bridge mode:
Wireless > Basic Wireless Settings
1. Log into the browser-based utility (see “How to open the browser-based
utility” on page8).
2. Click the Wireless tab, then click the Basic Wireless Settings page.
Local Wi-Fi MAC Address—The Wi-Fi MAC address of this device.
Remote Wireless Bridges’ Wi-Fi MAC Addresses—Enter the Wi-Fi
MAC addresses of other WAP300N wireless bridges that you want this
WAP300N to connect to.
Wireless Band—Select the 2.4 GHz or 5 GHz radio band. The 5 GHz band
is less crowded than the 2.4 GHz band, so that band is more likely to be
free from interference.
Channel Width—For best performance in a Wireless-N network, select
40MHz only (available only in the 5 GHz radio band) or Auto. In Auto
mode, this device and other WAP300N devices connected to this one
automatically switch to the 40MHz mode if there is no interference.
Channel—Choose the operating channel for your wireless network.
CAUTION
While in Wireless Bridge mode, this device can communicate with
other WAP300N devices only if they are also in Wireless Bridge mode
and the wireless settings are all identical.
Example 1
You want to connect two wired networks together using Two WAP300N
devices. One WAP300N will need to be on each network. We will call one (A)
and the other (B). To make this work:
1. Enter (A)’s Local Wi-Fi MAC Address into (B)’s Remote Wireless Bridges’ Wi-
Fi MAC Addresses field.
2. Enter (B)’s Local Wi-Fi MAC Address into (A)’s Remote Wireless Bridges’ Wi-
Fi MAC Addresses field.
Example 2
You want to connect three wired networks together using three WAP300N
devices. One WAP300N will need to be on each network. In this example, they
will be called (A), (B), and (C). To make this work:
1. Enter (A)’s and (C)’s Local Wi-Fi MAC Addresses into (B)’s Remote Wireless
Bridges’ Wi-Fi MAC Addresses field.
2. Enter (B)’s Local Wi-Fi MAC Address into (A)’s Remote Wireless Bridges’ Wi-
Fi MAC Addresses field.
3. Enter (B)’s Local Wi-Fi MAC Address into (C)’s Remote Wireless Bridges’ Wi-
Fi MAC Addresses field.
This establishes a wireless connection between (A) and (B) and another
connection between (B) and (C). This approach links all three wired
networks together.
CAUTION
Do not create a loop in your network. In the above example, a
loop would be adding an (A)-to-(C) wireless connection, while you
already had an (A)-to-(B) and (B)-to-(C) wireless connection.