NETGEAR WN370 User manual

Installation
Wall Mount Access Point
Model WN370
Package Contents
• Wall Mount Access Point
• Mounting bracket with four mounting screws
• Installation guide
Installation Requirements
The following items are required:
• 6 mm Phillips screwdriver
• T8 screwdriver
• Windows-based computer (Windows 7 or newer operating system)
• Standard EU or US wall outlet junction box with an Ethernet cable routed
through the wall from your LAN to the junction box
• IEEE 802.3af/at–compliant PoE switch or IEEE 802.3af/at–compliant PoE
injector
6. Connect the Ethernet cable providing PoE and network connectivity to the
PoE port on the back of the access point.
7. (Optional) Connect the Ethernet cable providing pass-through support to the
pass-through port on the back of the access point.
8. Mount the access point to the mounting bracket using the included T8
screws.
Network Environment
The WN370 access point can be deployed in a network managed by the following
NETGEAR wireless controller models:
• WC7500
• WC7600v2
• WC7600
• WC9500
If your network includes a DHCP server, option 43 must be enabled pointing
toward the IP address of the wireless controller.
Make sure that you are running the latest firmware version on your device.
To find documentation, firmware, soware, or other files, visit
downloadcenter.netgear.com.
Install the Access Point
The access point requires an electrical outlet junction box mounted in a wall.
¾To install the access point:
1. Remove the faceplate from the outlet junction box.
2. Run the Ethernet cable through the junction box with enough slack to reach
the access point.
3. Run the Ethernet cables through the
mounting bracket.
4. Align the mounting bracket with the holes
on the junction box.
5. Attach the mounting bracket to the
junction box using the included Phillips
head screws.

Support
Thank you for purchasing this NETGEAR product. You can visit
www.netgear.com/support to register your product, get help, access the latest
downloads and user manuals, and join our community. We recommend that you
use only ocial NETGEAR support resources.
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
français canadien à http://downloadcenter.netgear.com/other/.
(If this product is sold in Canada, you can access this document in Canadian
French at http://downloadcenter.netgear.com/other/.)
For the current EU Declaration of Conformity, visit
http://kb.netgear.com/11621.
For regulatory compliance information, visit
http://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
December 2017
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non-NETGEAR
trademarks are used for reference purposes only.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland
Discover the Access Point
¾To discover and configure the access point using a wireless controller:
1. Open a web browser, and in the browser’s address field, type the wireless
controller’s IP address.
2. Log in to the wireless controller.
The wireless controller’s local browser–based management interface page
displays.
3. Select Access Point > Discovery Wizard.
4. Follow the onscreen steps to discover the access point and review the
discovery results.
5. Add the access points that you want to be managed by the wireless controller
to the Managed AP List.
6. Make sure that the country is set to the location where the device is
operating.
You must comply with the local, regional, and national regulations set for
channels, power levels, and frequency ranges.
For more information about the Discovery Wizard and the managed AP list, see
the wireless controller user manual. To view or download the user manual, visit
downloads.netgear.com/files/GDC/WC7500/WC_AllModels_UM.pdf.
Verify Connectivity
From a computer or mobile device, verify that you can connect to the WiFi
network of the access point. You can also check the access point LEDs to verify a
successful installation and connection.
LED Description
Power • Solid amber. The access point is booting.
• Slow blinking amber. The access point is not managed by a
wireless controller.
• Green. The access point booted and is managed by a wireless
controller.
Activity • Blinking green. Network trac through the access point.
• O. No network trac through the access point is detected.
WiFi On/O • Solid green. The access point’s WiFi is active.
• O. The access point’s WiFi is o.