MuxLab 500533 User manual

USB-C HDMI 5x1 Presentation Switcher with Dante
User Manual
500533
© MuxLab Inc. 2023 1 94-001030-A/SE-001030-A

USB-C/HDMI 5x1 Presentation Switcher with Dante
Table of Contents
1. Safety Precautions....................................................................................................................................................3
2. Introduction................................................................................................................................................................4
3. Features.......................................................................................................................................................................4
4. Package Contents...................................................................................................................................................5
5. Specifications............................................................................................................................................................5
6. Operation Controls and Functions....................................................................................................................7
6.1. Switcher panel..................................................................................................................................................7
6.2. HDBaseT Receiver Panel..............................................................................................................................9
6.3. IR Cable pin Assignment.............................................................................................................................10
6.4. IR Remote..........................................................................................................................................................10
7. Web GUI User Guide.............................................................................................................................................11
8. Dante Web GUI User Guide...............................................................................................................................21
9. RS-232 Control Command.................................................................................................................................24
10. Application Diagram..........................................................................................................................................38
© MuxLab Inc. 2023 2 94-001030-A/SE-001030-A

1. Safety Precautions
To ensure the best performance from the product, please read all instructions carefully before
using the device. Save this manual for future reference.
Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
Do not dismantle the housing or modify the module. It may result in electrical shock or
burns.
Do not open or remove the housing of the device as you may be exposed to dangerous
voltage or other hazards.
To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install
this product near water. Keep the product away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an
object or liquid falls or spills on the housing, unplug the module immediately.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
Using supplies or parts not meeting the product specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
Install the device in a place with adequate ventilation to avoid damage caused by
overheat.
Unplug the power when left unused for a long period of time.
Information on disposal of devices: do not burn or mix with general household waste,
please treat them as normal electrical waste.
Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated
without the express permission of MuxLab Inc. Product specifications and information in this
document are for reference only, and the content may be updated from time to time without
prior notice.
© MuxLab Inc. 2023 3 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

3. Features
18Gbps video bandwidth 5x1 switcher
HDMI 2.0b, HDCP 2.2 an DP 1.2 complaint
Support video resolution up to 4K/60Hz 4:4:4
Support HDBaseT 3.0 with PoE
Support 5x1 seamless switching
Up to 5 categories of multiview display modes: Single/PIP/PBP/Triple/Quad
Dante 2x2 audio embedding input and output
Local USB 2.0 KVM switching and extending USB 2.0 over HDBT 3.0
Support analog/Dante audio embedding, analog/Dante audio de-embedding output
Manual switching or automatic switching
CEC/RS-232 control external devices
Flexible control via front panel buttons, IR remote, RS-232, TCP/IP or Web GUI
Advanced EDID management
Support standard PoE power supply (TX_PSE, RX_PD)
2. Introduction
Introducing the Muxlab USB-C HDMI 5x1 Presentation Switcher with Dante (Model: 500533):
Enhance your audiovisual experiences with the Muxlab USB-C HDMI 5x1 Presentation Switcher,
a cutting-edge solution designed for seamless connectivity and advanced presentation
capabilities. This versatile switcher offers a myriad of features to meet your diverse multimedia
needs.
The Muxlab USB-C HDMI 5x1 Presentation Switcher with Dante combines innovation with
functionality, providing a superior solution for presentations, conferences, and multimedia
applications. Elevate your audiovisual experiences with this state-of-the-art presentation
switcher.
© MuxLab Inc. 2023 4 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

© MuxLab Inc. 2023 5 94-001030-A/SE-001030-A
4. Package Contents
One (1) USB-C HDMI 5x1 Presentation Switcher with Dante
One (1) HDBaseT Receiver
One (1) IR Blaster cable (1.5 meters)
One (1) IR Wideband Receiver Cable (1.5 meters)
One (1) IR Remote Control
Two (2) 3pin-3.5mm Phoenix Connector (male)
Three (3) 5-pin Phoenix Connector
One (1) 24VDC/8A Desktop Power Supply and AC Power Cord (1.5 meters)
Four (4) Mounting Ear (Matrix and Receiver)
One (1) User manual (available via download)
5. Specifications
HDMI Compliance HDMI 2.0b
HDCP 2.2
18Gbps
48KHz
Technical
HDCP Compliance
Video Bandwidth
Input Video Resolution
Color Space
Audio Sample Rate
1080P&4K30 -- 230ft/70m; 4K60 -- 131ft/40mTransmission Distance
Input supports HDR, output does not support HDR.HDR
Color Depth
Human-body Model: ±8kV (Air-gap discharge), ±4kV (Contact discharge)
ESD Protection
TX Analog Audio
480i ~1080p50/60Hz, 4Kx2K@24/30Hz, 4K2K@50Hz/60Hz 4:4:4
Output Video Resolution
Auto, 3840x2160p60, 3840x2160p50, 4096x2160p60, 4096x2160p50,
3840x2160p30, 3840x2160p25, 1920x1200p60RB, 1920x1080p60,
1920x1080p50, 1360x768p60, 1280x800p60, 1280x720p60, 1280x720p50,
1024x768p60
Input: 8/10/12-bit, 8-bit (4K60Hz 4:4:4) Output: 8-bit
RGB, YCbCr 4:4:4 / 4:2:2, YUV 4:2:0
Audio Formats LPCM 2.0
Input Impedance
Line Output Level (Max)
Output Impedance
Line Input Level (Max)
10K Ohms
330 Ohms
8.2dBu (2Vrms)@ balanced or unbalanced audio
8.2dBu (2Vrms)@ balanced, 2.2dBu (1Vrms)@ unbalanced audio
Frequency Response
Audio Output Sync Delay
Audio S/N Ratio
Audio THD+N
(+0.5 dB, -1 dB) 20 Hz to 20 kHz
0 to 50ms
93dB @ 2Vrms, 1kHz A-weighted
<0.1% @ 0dBV, 1kHz
RX Analog Audio
Line Output Level (Max)
Output Impedance
Line Input Level (Max)
330 Ohms
8.2dBu (2Vrms)@ balanced or unbalanced audio
8.2dBu (2Vrms)@ balanced, 2.2dBu (1Vrms)@ unbalanced audio
Frequency Response (+0.5 dB, -1 dB) 20 Hz to 20 kHz
USB-C/HDMI 5x1 Presentation Switcher with Dante

© MuxLab Inc. 2023 6 94-001030-A/SE-001030-A
Receiver
Inputs:
Outputs:
Control:
1 x HDMI IN [TypeA, 19-pin female]
1 x HDBaseT IN [RJ45]
1 x HDMI OUT [Type A, 19-pinfemale]
1 x LINE OUT [5pin-5mm phoenix connector]
1 x RS-232 [3pin-3.5mm phoenix connector]
1 x USB HOST [USB Type B]
2 x USB DEVICES [USB Type A]
1 x SERVICE [Micro USB]
1 x IR IN [3.5mm stereo mini-jack]
1 x IR OUT [3.5mm stereo mini-jack]
Mechanical
Generic Specification
Housing Metal enclosure with front aluminum plate
Color Black
Dimensions (WxDxH) Transmitter: 220mm[W]×150mm[D]×44mm[H]
Receiver: 140mm[W]×105mm[D]×21.5mm [H]
Weight Transmitter: 1.21Kg; Receiver: 424g
Power Supply Input: 100 - 240VAC 50/60Hz Output: 24VDC/8A
Power Consumption 150W (Max)
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity 20~90% RH (non-condensing)
Compliance
Warranty
Order Information
Regulatory: FCC, CE, RoHS
2 years
500533 USB-C HDMI 5x1 Presentation Switcher with Dante (UPC: 627699005330)
Transmitter
Inputs:
Outputs:
Control:
3 x HDMI INPUT [Type A, 19-pinfemale]
2 x USB-C [24-pin female]
1 x LINE IN [5pin-3.5mm phoenix connector]
1 x DANTE [RJ45]
1 x HDMI OUTPUT [Type A, 19-pinfemale]
1 x HDBT OUTPUT [RJ45]
1 x LINE OUT [5pin-3.5mm phoenix connector]
1 x RS-232 [3pin-3.5mm phoenix connector]
1 x LAN [RJ45]
1 x USB HOST [USB Type B]
2 x USB DEVICES [USB Type A]
1 x IR IN [3.5mm stereo mini-jack]
1 x IR OUT [3.5mm stereo mini-jack]
Connection
Audio Output Sync Delay
Audio S/N Ratio
Audio THD+N
0 to 50ms
93dB @ 2Vrms, 1kHz A-weighted
<0.1% @ 0dBV, 1kHz
Dante Audio
Audio Delay
Audio Formant
Sample Rate
LPCM2.0
44.1, 48, 88.2 and 96KHz at 24 bits
2ms, 3ms, 4ms, 5ms and 10ms
Network Bandwidth 100Mbps
USB-C/HDMI 5x1 Presentation Switcher with Dante

3
Press this button to cycle through the preset application scenes. The button light
will automatically turn off after 1 second each time. The scenes can be preset
throughthe Web GUI.
2
Press and hold this button for 3 seconds, the product will enter standby mode
and the button light will be on. In standby mode, short press this button,the
product will be turned on and the
button light will be off.
© MuxLab Inc. 2023 7 94-001030-A/SE-001030-A
6. Operation Controls and Functions
6.1 Switcher Panel
Front Panel
1
No
4
Name Function Description
IR signal receiving window, receiving the IR remote signal.
In single screen display mode, press the USB-C 1 / USB-C 2 / HDMI 3 / HDMI 4
/ HDMI 5 button to select the signal input channel, and the corresponding
button light will be on.
In Multiview mode, input button lights indicate the outputs, for example, when
USB-C 1, HDMI 3 and HDMI 5 port are the signal input channels for triple display
mode, the corresponding USB-C 1, HDMI 3 and HDMI 5 button lights will be on.
When USB-C 1 port is the shared signal input channel for triple display mode,
only the corresponding USB-C 1 button light will be on.
It can be set through the Web GUI. Press any input button will switch back to the
single screen display mode. The button light will turn off automatically after 1
second each time.
IR Window
USB-C 1 / USB-C 2 /
HDMI 3 / HDMI 4 /
HDMI 5 Buttons
AUTO Button
5
PRESET Button
POWER Button
Press this button to enable/disable the auto switching function. When the auto
switching function is enabled, the button light will be on.
USB-C/HDMI 5x1 Presentation Switcher with Dante

1
3
2
Analog audio input port, supporting balanced/unbalanced audio input
Power port, connect the 24VDC power adapter.
© MuxLab Inc. 2023 8 94-001030-A/SE-001030-A
Rear Panel
Connect the IR receiver cable, used for IR signal pass-through or controlling
this product via the IR remote.
No
4
Name Function Description
RS-232 serial port, used for RS-232 signal pass-through or controlling this
product via RS-232 commands.
LAN Port
RS-232 Port
IR OUT Port
Connect to a router or Switch for Internet access or Web GUI control.
RESET Button
5
DANTE Port Dante Network port, connected to the Switch with other Dante devices on
Ethernet Switch.
6
7
DC 24VDC
8
Press and hold this button for 5 seconds to restore to factory default settings.
LINE IN Port
IR IN Port
Connect the IR blaster cable, the IR signal is from the IR IN port of the HDBaseT
Receiver.
LINE OUT Port Analog audio output port, supporting balanced/unbalanced audio output.
9
10 HDBT OUTPUT Port Connected to the HDBaseT IN port of the receiver with a CAT6A cable.
11
▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
Link Signal Indicator
▪ Illuminating: Switcher and Receiver are in good connection status.
▪ Flashing: Switcher and Receiver are in poor connection status.
▪ Dark: Switcher and Receiver are not connected.
Data Signal Indicator
12
Two USB extension ports, connected to mouse, keyboard, USB camera or other
USB devices.
HOST 3 port
13
14
USB DEVICES Ports
HDMI signal input ports, connected to HDMI source devices.
15
HDMI 3/4/5 INPUTS
USB Host port, connected to PC.
16
HDMI signal output port, connected to HDMI display device.
17
USB-C 1/2 Ports USB-C signal input port, connected to USB-C signal source
device, with the function of 60W charging.
HDMI OUT Port
USB-C/HDMI 5x1 Presentation Switcher with Dante

1
3
2
Connect to IR receiver cable, the IR receive signal will emit to the “IR OUT”
port of the Switcher.
Two USB extension ports, connected to USB camera or other USB devices.
© MuxLab Inc. 2023 9 94-001030-A/SE-001030-A
When the HDBaseT IN port is selected as the signal input channel, the green
HDBT LED will be on.
No
4
Name Function Description
VIDEO LED
HDMI LED
LINK LED
5
6
7
DEVICES Ports
8
IR IN Port
HDBT LED
When the HDMI IN port is selected as the signal input channel, the green HDMI
LED will be on.
IR OUT Port
9
10
HDBT IN Port Connected to the HDBaseT out port of the Switcher with a CAT6A cable.
11
▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
Connection Signal Indicator
(Green)
▪ Illuminating: Switcher and Receiver are in good connection status.
▪ Flashing: Switcher and Receiver are in poor connection status.
▪ Dark: Switcher and Receiver are not connected.
Data Signal Indicator
(Yellow)
12
Firmware update port.
SERVICE Port
13
14 HDMI IN Port HDMI signal input port, connected to HDMI source device.
15 HOST Port USB Host port, connected to PC.
16 HDMI signal output port, connected to HDMI display device
17 LINE OUT port Analog audio output port, supporting balanced and unbalanced audio output.
HDMI OUT Port
6.2 HDBaseT Receiver Panel
Power LED Red LED will be on when the receiver is powered on.
Connect to IR blaster cable, the IR emit signal is from the “IR IN” port of the
Switcher.
SELECT Button Press this button to select signal input channel.
▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
▪ Illuminating: Switcher and Receiver are in good connection status.
▪ Flashing: Switcher and Receiver are in poor connection status.
▪ Dark: Switcher and Receiver are not connected.
18 RS-232 Port RS-232 signal pass-through or controlling this receiver via RS-232 commands.
19 DC 24VDC Port Optional 24VDC power adapter, the receiver also can be powered by PoE.
USB-C/HDMI 5x1 Presentation Switcher with Dante

© MuxLab Inc. 2023 10 94-001030-A/SE-001030-A
6.3 IR Cable pin Assignment
The pin assignment of the IR Receiver cable and IR Blaster cable is as below:
Note: When the angle between the IR receiver and the remote control is ± 45°,
the transmission distance is 0-5 meters; when the angle between the IR receiver
and the remote control is ± 90 °, the transmission distance is 0-8 meters
6.4 IR Remote
① Power button: Power on the switcher or set it to standby mode.
② VIDEO buttons:
USB-C 1 / USB-C 2 / HDMI 3 / HDMI 4 / HDMI 5: Select input source in
single screen display mode, the button light on the front panel will light.
: Select the last or next input source in single screen display mode.
AUTO: Enable/disable the auto switching function.
PRESET: Select preset application scenes.
: Multiview display mode switching button: Single, PIP, PBP, triple, Quad.
RES.: Press this button to cycle through the output resolution.
FREEZE: Press this button to freeze/unfreeze the screen.
RX HDBT: Select the HDBaseT IN port as the signal source on the receiver.
RX HDMI: Select the HDMI IN port as the signal source on the receiver.
③ AUDIO buttons:
USB-C 1 / USB-C 2 / HDMI 3 / HDMI 4 / HDMI 5 / WIN 1 / AIN /
DANTE: Select the audio input channel for the HDMI/HDBT output.
Note: USB-C 1, USB-C 2, HDMI 3, HDMI 4, HDMI 5 and WIN 1
belongs to the audio input channels of Main In (HDMI/USB-C In).
Mute: Press this button to mute / unmute the audio of Master Out.
VOL-, VOL+: Increase / decrease the audio output volume of Master Out.
USB-C/HDMI 5x1 Presentation Switcher with Dante

© MuxLab Inc. 2023 11 94-001030-A/SE-001030-A
7. Web GUI User Guide
The presentation switcher can be controlled by Web GUI interface. The operation
method is as below:
Step 1: Get the current IP Address.
The default IP address is 192.168.0.100 (when the system is not connected to a router).
You can get the current switch IP address via RS-232 command control by sending the
ASCII command “r ip addr” through a Serial Command tool.
For the more details on RS-232 control, please refer to “9. RS-232Control Command”.
Step 2: Connect the LAN port of the presentation switch to a PC with a UTP patch cable
and set the IP address of the PC to be in the same network segment of the presentation
switcher.
Step 3: Enter the current IP address of presentation switcher into your browser on the
PC to enter Web GUI interface.
After accessing the Web GUI page, there will be a Login interface, as shown below:
The default username and password are as below:
Username User Admin
Password user admin
USB-C/HDMI 5x1 Presentation Switcher with Dante

User Page:
You can do the following operations on the User page:
① Preset: Recall the preset application scenes.
② Video: Set the multiview display mode, select input source for each screen, freeze the
screen or mute the audio.
③ Master Out: Set the audio volume or mute/unmute the audio for Master Out. You can
respectively turn on/off the HDMI/HDBT Out, Line Out or Dante Out.
In the Login interface, select the username “Admin” and input the password “admin”, then
click the “Login” button to enter the Information page of the Admin interface.
Information Page:
© MuxLab Inc. 2023 12 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

The Information page provides basic information about the model name, software
version, IP information and the current machine temperature. Besides, you can do the
following operations on each page of the Admin interface.
① Display and set the audio volume of Master Out. Click the volume icons to increase/
decrease the audio volume of Master Out, or click the mute icon to mute/unmute the
audio of Master Out. When muted, the mute icon displays red.
② Display the current username (User or Admin).
③ Click the power icon to power on the switch or set it in standby mode.
④ Click the logout icon to logout and return to the login interface.
Status Page:
The Status page displays the input & output port connection status, input and output
resolution, Color Space, Color Depth and HDCP.
Preset Page:
5 preset scenes on the Preset page can be set.
① Preset Name: You can name the preset scene.
② Preset Save: Click the Save button to save the scene.
③ Preset Clear: Click the Clear button to clear the saved scene.
④ Preset Recall: Click the Recall button to recall the saved scene.
© MuxLab Inc. 2023 13 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

EDID Page:
You can do the following operations on the EDID page.
① Click the drop-down list to set EDID for each input port. The EDID list is as below.
② Click the drop-down list to select USB-C 1\USB-C 2\HDMI 3\HDMI 4\HDMI 5\HDMI
OUT\ HDBT OUT for EDID download.
③ Click the Download button to download EDID and generate a .bin file.
④ Display the downloaded EDID .bin file.
⑤ Click the Load EDID button to download user-defined EDID. Please note that only. bin
files are supported.
⑥ Click the Save EDID button to save the user-defined EDID.
© MuxLab Inc. 2023 14 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

Video Page:
Switch Mode
① Auto Switch: You can turn on/off the auto switching function.
② Fallback Input: Click the drop-down list to select Auto\USB-C 1\USB-C 2\HDMI
3\HDMI 4\HDMI 5 as the signal source of Fallback input. When the auto switching
function is turned on and the current input source is disconnected, the Fallback input
signal source will be selected automatically. When the Fallback input is set to be Auto, the
switch will detect and switch to the signal with the auto switching sequence of USB-C
1>USB-C 2->HDMI 3->HDMI 4-> HDMI 5.
Note: The auto switching function is available only in single screen display mode.
Window layout
① Window layout: Click the drop-down list to select the display mode
(1.Single\2.PIP\3.PBP\ 4.Triple\5.Quad).
② Freeze: You can freeze the screen.
③ AV Mute: You can mute the audio and video.
④ PIP Position: Click the drop-down list to select the display position in PIP display mode.
⑤ PIP Size: Click the drop-down list to select the display size in PIP display mode.
⑥ Display Mode: Click the drop-down list to select the display mode in PBP\Triple\Quad
display mode.
⑦ Display Aspect: Click the drop-down list to select the display aspect in
PBP\Triple\Quad display mode.
⑧ Border: Click the drop-down list to select the border and border color in
PBP\Triple\Quad display mode.
© MuxLab Inc. 2023 15 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

Output Setting
① Resolution: Click the drop-down list to select the output resolution. The output
resolution list is as following:
Note: When the output resolution is set to Auto, the switch will output the matching
resolution based on the EDID of the back-end TV.
② HDMI HDCP: Click the drop-down list to select the HDMI HDCP version.
③ HDBT HDCP: Click the drop-down list to select the HDBT HDCP version.
After setting up, click “Save” to take effect.
Audio Page:
© MuxLab Inc. 2023 16 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

Source Select
① Main In: Click the drop-down list to select the signal source for Main In.
② HDMI/HDBT Out: Click the drop-down list to select the signal source for HDMI/HDBT
Out.
③ Line Out: Click the drop-down list to select the signal source for Line Out.
④ Dante Out: Click the drop-down list to select the signal source for Dante Out. After
setting up, click “Save” to take effect.
Input Setting: You can respectively set the output volume or mute/unmute the audio for
Main In (HDMI/USB-C In)\Line In\Dante In.
Output Setting
① Master Out: You can respectively set the output volume or mute/unmute the audio for
HDMI/HDBT Out\Line Out\Dante Out, or set together when turning on three options
synchronously.
② HDMI/HDBT Out\Line Out\Dante Out: Click the drop-down list of Mix to select the
audio output channel for HDMI/HDBT Out\Line Out\Dante Out. You can set the delay,
increase/decrease the audio or mute/unmute the audio.
GEQ Setting
① Output: Click the drop-down list to select the output channel.
② Equalizer: Click the drop-down list to set the equalizer.
Flat: Set all EG to 0db.
Custom1: Set EQ for custom 1.
Custom2: Set EQ for custom 2.
Custom3: Set EQ for custom 3.
Custom4: Set EQ for custom 4.
Custom5: Set EQ for custom 5.
© MuxLab Inc. 2023 17 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

USB Page:
USB Switch
① Follow Video: Click this button to set the USB transmission follow the video. It will follow
the video output of window 1 in multiview mode.
② Manual Switch: Switch to USB-C 1\USB-C 2\Host 3 manually.
③ Auto Switch: Detect and switch to USB-C 1\USB-C 2\Host 3 automatically.
After setting up, click “Save” to take effect.
RS-232 Page:
RS-232 Settings
① Local RS-232: You can set the Baud Rate, Data Bit, Parity and Stop Bit for the RS-232
port of the transmitter.
② Remote RS-232: You can set the Baud Rate, Data Bit, Parity and Stop Bit for the RS-232
port of the receiver.
© MuxLab Inc. 2023 18 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

RS-232 Commands (Display Auto Power)
① Local/Remote RS-232 Commands: You can turn on/off the local/remote RS-232
commands and hex.
② Display On/Off Command: You can input the display on/off command of the device.
③ Delay 1: You can set the delay time for the next action (such as send the Display Input
Select command).
④ Display Input Select: You can input the command of switching the input channel for the
display device.
⑤ Delay 2: You can set the delay time for the next action after sending the Display Input
Select command.
After setting up, click “Save” to take effect.
Network Page:
① Network Configuration: You can set the IP Mode (DHCP/Static), IP Address, Subnet
Mask, Gateway, Telnet Port and Domain Name.
Note: The Domain Name “500533-167BA.local” can be used to login the Web GUI.
② Account Passwords: You can modify the login password for User and Admin. After
setting up, click “Save” to take effect.
© MuxLab Inc. 2023 19 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante

System Page:
Display Control
① CEC Command: You can power on/off the CEC command.
② Display Auto Power: You can turn on/off the Display Auto Power. When it is set to ON,
you can control the display device power on/off or switch the port based on the power
status (power on/standby) or the signal input status of the transmitter by sending serial
port or CEC Power On/Off command.
③ Auto Power off Timer: Click the drop-down list to select the delay time for sending the
command to turn off the display device when the transmitter is in standby mode or there is
no signal input.
④ Control Type: Click the drop-downlist to select the control type.
System Utilities
① Front Panel Buttons: Click “ON/OFF” to lock/unlock panel buttons. “On” indicates that
panel buttons are available; “OFF” indicates panel buttons are unavailable.
② Beep: Click “ON/OFF” to turn on/off the beep.
③ USB-C Ethernet Access: Click “ON/OFF” to turn on/off the Ethernet access function of
USB-C.
④ Fan Speed: Click the drop-down list to set the fan speed.
⑤ Reboot: Click “Reboot” to reboot the switch.
⑥ Restore Factory Settings: Click this button to restore the switch to factory settings.
⑦ Export Settings: Click this button to export configuration files.
⑧ Import Settings: Click this button to import configuration files.
Firmware Update: You can update the software of MCU, Web, Scaler or receiver. Click
“Choose File” to select the update file, then click “Update” to start update. When the
progress bar reaches 100%, the update is complete.
© MuxLab Inc. 2023 20 94-001030-A/SE-001030-A
USB-C/HDMI 5x1 Presentation Switcher with Dante