MV Agusta AMO R 2022 Instruction manual

AMO R
AMO RR
AMO SV
AMO XT PINION
AMO RR PINION
MV Agusta Motor S.p.A.
Via G. Macchi, 144
21100 Varese
www.mvagusta.com
C
M
Y
CM
MY
CY
CMY
K
ai16553055657_Copertina completa_AMO_03-2022.pdf 1 15/06/2022 17:06:06

MANUAL FOR USE AND MAINTENANCE
(Translation of Original Instructions)
EN - 1
Bici ELETTRICA_03-2022.indd 1Bici ELETTRICA_03-2022.indd 1 15/06/2022 17:07:5415/06/2022 17:07:54

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 2
This manual is an integral part of the ve-
hicle and must accompany it even in the
event of sale.
The Manufacturer reserves the right to
make changes to its models, notwithstand-
ing the essential characteristics described
and shown her.
The rights of electronic storage, reproduc-
tion, total and partial adaptation with any
means are reserved for all Countries.
The quote of products or services of third
parties is for informative purposes only and
does not entail any obligation.
The Manufacturer accepts no liability for the
performances or use of these products.
Edition: 05/2022.
Produced by:
DUESSE SERVICE srl
Samarate (VA)
www.duesse.it
on behalf of:
e-MV Agusta S.r.l.
Via Caronaccio, 67
21040 - Morazzone (VA) - ITALY The bicycles with the trademark “MV AGUSTA” are designed and built by e-MV Agusta S.r.l.
To request assistance, please write at: emv[email protected]
Bici ELETTRICA_05-2022.indd 2Bici ELETTRICA_05-2022.indd 2 16/06/2022 09:17:3216/06/2022 09:17:32

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 3
GENERAL INDEX
0.1 INTRODUCTION...........................................5
0.2 MEANING OF “EPAC” -
Electrical Power Assisted Cycle................5
0.3 DESCRIPTION OF SYMBOLS.....................6
0.4 NOTES FOR PARENTS AND LEGAL
GUARDIANS ................................................6
0.5 COMPONENTS INSTALLED ON THE
BICYCLE ......................................................6
0.6 DISPOSAL ...................................................6
1.1 INFORMATION ON SAFETY........................7
1.1.a Correct use .........................................8
1.1.b Non-compliant use..............................8
1.1.c Legal Regulations...............................8
1.1.d Residual hazards................................8
 1.1.e Atrstuse ...........................................9
1.1.f Before every use...............................10
1.2 CARE OF THE BATTERY PACK................10
1.3 WHICH OPERATIONS CAN BE
CARRIED OUT AUTONOMOUSLY
BY THE USER ON THE BICYCLE.............11
1.4 SAFETY PROVISIONS DURING USE .......11
1.5 PRECAUTIONS FOR MOUNTING
OF ACCESSORIES OR
COMPONENTS FOR MODIFICATIONS.....12
1.6 WHO CAN DRIVE THIS EPAC
BICYCLE.....................................................12
1.7 WARRANTY CONDITIONS........................13
1.7.a Pre-requisites for the request for
warranty............................................13
1.7.b Exclusion from warranty....................13
1.8 IDENTIFICATION OF THE BICYCLE.........14
2.1 OVERALL DIMENSIONS............................15
2.2 TIGHTENING TORQUES............................16
2.3 TECHNICAL DATA .....................................17
2.4 IDENTIFICATION OF THE BICYCLE
COMPONENTS...........................................18
2.4.a Content of the supplied kit ................20
2.5 REMOVAL FROM PACKAGING.................21
2.5.a Assembly of parts .............................21
2.5.b Basket assembly
(AMO XT PINION).............................22
2.6 ADJUSTMENTS .........................................23
2.6.a Saddle height adjustment .................23
2.6.b Saddle inclination adjustment............24
2.6.c Brakes levers adjustments................25
2.7 OPTIONAL ACCESSORIES.......................26
2.8 DESCRIPTION OF THE BICYCLE.............26
2.8.a Brakes...............................................26
2.8.b Belt transmission...............................26
2.8.c Motor and electric devices................27
2.8.d Motor and electric devices
(PINION)...........................................28
3.1 BEFORE EVERY USE OF THE BICYCLE.29
3.2 CHECK OF WHEELS AND TIRES.............30
 3.2.a Wheelsxingcheck ..........................30
3.2.b Tires check........................................30
3.2.c Tires valve check ..............................30
3.2.d Tires pressure check.........................31
3.2.e Wheels check....................................31
3.3 SADDLE AND SEATPOST CHECK...........32
3.4 HANDLEBARS CHECK .............................32
3.5 BRAKES CHECK .......................................34
3.6 BELT CHECK AND PEDAL
CRANKS FIXING........................................35
3.7 ELECTRIC MOTOR CHECK ......................35
3.8 BATTERY CHARGE
STATUS CHECK.........................................35
3.9 VARIOUS
ACCESSORIES CHECK ............................35
3.10 OTHER CHECKS........................................35
4.1 ON/OFF BUTTON, BATTERY STATUS,
ASSISTED PEDALLING COMMANDS......36
 4.1.aSwitchingon/O󰀨ofthebicycle........36
 4.1.bSwitchinglightson/o󰀨(AMOXT) ......36
4.1.c Assistance to pedalling.....................37
4.1.d Error messages.................................37
4.1.e Bluetooth®pairingandnotications...37
5.1 USE OF THE BICYCLE..............................38
5.1.a Operating temperatures....................38
5.2 USE OF THE BRAKES...............................39
5.3 USING THE GEARBOX (PINION)..............39
5.4 USING THE BAGGAGE HOLDER
(AMO XT)........................................................40
5.5 WHAT TO DO AFTER A POSSIBLE FALL 41
5.6 HOW TO TRANSPORT THE BICYCLE .....42
5.7 RECHARGING THE BATTERY PACK .......42
 5.7.a Vericationofthebatterypack..........42
5.7.b Recharging the battery pack.............43
5.8 NOTES ON THE BATTERY AUTONOMY..45
6.1 CHECKS, CLEANING AND CARE.............46
6.1.a Maintenance of the battery pack.......46
Bici ELETTRICA_03-2022.indd 3Bici ELETTRICA_03-2022.indd 3 15/06/2022 17:07:5415/06/2022 17:07:54

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 4
6.1.b Checks after every use of
the bicycle.........................................47
6.2 PERIODIC MAINTENANCE PROGRAM....47
6.3 CLEANING OF THE BICYCLE...................48
6.4 STORING THE BICYCLE...........................48
6.5 DISASSEMBLY / ASSEMBLY OF THE
FRONT WHEEL..........................................49
6.6 DISASSEMBLY / ASSEMBLY OF THE
REAR WHEEL ............................................50
6.7 BELT TENSIONING CHECK......................52
6.8 BRAKES PADS WEAR CHECK.................53
6.9 DEFLATED TIRE ........................................53
6.10 CHECKING GEARBOX SHEATHS
AND CABLES (PINION).............................53
6.11 CLEANING AND GREASING THE
GEARBOX PULLEY (PINION) ...................54
6.12 REPLACING GEARBOX OIL (PINION) .....54
6.13 OTHER OPERATIONS ...............................55
6.14 WINTER STORAGE...................................55
7.1 TROUBLESHOOTING................................56
7.1.a Generic inconveniences....................56
7.1.b PINION system problems .................57
“MVride” App .....................................................57
DECLARATION OF CONFORMITY ...................58
Bici ELETTRICA_03-2022.indd 4Bici ELETTRICA_03-2022.indd 4 15/06/2022 17:07:5415/06/2022 17:07:54

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 5
0.1 INTRODUCTION
Dear Customer,
thank you for purchasing our product.
Our electric bicycle is a combination of inno-
vation, design and comfort and has been de-
signed and manufactured exclusively in Italy.
The innovative concept of assisted pedalling
will revolutionize your cycling habits and open
upnewhorizons; assistedpedallingo󰀨ers a
more comfortable ride without detracting any-
thing from the healthy pleasure of cycling.
This bicycle has been manufactured using the
highest quality materials in conformity with all
the applicable standards and regulations.
Before using your new bicycle, we strongly
recommend that you read and familiarize with
the information and instructions contained in
this user and maintenance handbook (hereaf-
ter referred to as “Manual”).
NOTE: Keep this handbook for future consul-
tation.
0.2 MEANING OF “EPAC” -
Electrical Power
Assisted Cycle
NOTE: Only for the member countries of the
European Community.
The acronym EPAC derives from the initials
of Electrical Power Assisted Cycle which
is the description of what is commonly called
Electric Bicycle with Assisted Pedalling.
InordertobeassignedtheEPACclassica-
tion, an electric bicycle must satisfy the re-
quirements set out in the European Standard
EN 15194-2008 and the Machinery Directive
2006/42/EC.
In short, in order to be approved for EPAC
classication,anelectricbicyclemustcom-
ply with the following requirements:
- Auxiliary electric motor having a maximum
continuous rated power of 0,25kW.
- Propulsive power cut-o when the cyclist
stops pedalling.
- Progressive reduction of the electric motor
assistance as speed increases and com-
plete cut-o once the maximum speed of
25km/h is exceeded.
ATTENTION
Respecting the Directives and
maintaining the essential re-
quirements allow to use Your
bicycle in compliance with the
regulations in force in the coun-
try of use.
Interventions that change the
mode of operation of Your EPAC
bicycle are indictable and pun-
ishable as provided for by Law.
If necessary, before using Your
EPAC bicycle on the road, have
all the optional devices pre-
scribed by the tra󰀩c code in-
stalled by a qualied operator.
In some countries it may be necessary to en-
sure that the bicycle specications comply
with the locally applicable standards.
Check all these requirements before using the
bicycle.
Bici ELETTRICA_03-2022.indd 5Bici ELETTRICA_03-2022.indd 5 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 6
0.3 DESCRIPTION OF SYMBOLS
This manual contains a series of symbols that
are intended to draw your attention to particu-
larly important information and instructions.
Their meaning is explained below:
HAZARD
This symbol indicates a poten-
tial falling hazard and the con-
sequent risk of personal injury
and damage (to both yourself
and third parties).
ATTENTION
This symbol indicates that an
improper behaviour may result
in damage to property or the en-
vironment.
NOTE: This symbol indicates important infor-
mation designed to help you get the best out
of Your bicycle.
Respect the prescribed tightening
torque:
In the presence of this symbol it is necessary
to respect the correct tightening torque to en-
sure safety during use of the bicycle. This is
only possible by using a torque wrench. If you
do not possess such a tool, we recommend
tohavethisoperationcarriedoutbyqualied
personnel. The components installed with the
incorrect torque may break or detach causing
serious falls.
0.4 NOTES FOR PARENTS
AND LEGAL GUARDIANS
Parents and legal guardians are responsible for
the actions and safety of the children under their
care, as well as the safe condition of the bicycle
and its suitability for the size of the cyclist.
This bicycle is NOT suitable to be used by
children, however, if you decide that the child
is capable of using it, you must ensure that
he/she is fully aware of how to use the EPAC
bicycle safely and responsibly.
The best way to verify this is to allow him/her
to ride it in the environment the bicycle was
designed to be used in.
0.5 COMPONENTS INSTALLED
ON THE BICYCLE
On the bicycle are mounted parts which are not
produced by the manufacturer, inside the manual
youwillndtheinstructionsfortheseparts,which
the user needs for correct operation of the bicycle.
For further information, please refer to man-
ufacturer’s manuals of the parts available on
the respective internet websites.
0.6 DISPOSAL
The bicycle and its components such as mo-
tor, control display, battery, speed sensor, ac-
cessories and packaging must be disposed of
while respecting the environment. It is pro-
hibited to dispose of the electric bicycle and
its components in domestic waste.
Directive 2012/19/EU
The mark that appears on the prod-
uct and associated documentation
indicates that it must not be disposed of to-
gether with normal household waste at the
end of its working life.
In order to avoid health or environmental
damages resulting from incorrect disposal of
waste materials, you are requested to sep-
arate this product from other types of waste
and recycle it responsibly in order favour the
sustainable reuse of recyclable materials.
Private users are invited to contact the vendor
from whom they purchased the product or the
relevant local authority for all the information
necessary about recycling this type of product.
Commercial users are invited to contact their
supplier and check the terms and conditions
stipulated in the sales contract.
Bici ELETTRICA_03-2022.indd 6Bici ELETTRICA_03-2022.indd 6 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 7
This product must not be disposed of together
with other commercial waste.
ATTENTION
Preserve packaging of the bat-
tery supplied with the bicycle. In
case of shipping of the battery
pack, use the original packag-
ing as the battery pack is con-
sidered a “Dangerous Good”.
1.1 INFORMATION ON
SAFETY
- This user and maintenance manual con-
tains all the information necessary to
familiarize with your EPAC Bicycle, un-
derstand the main components and the
associated technology, and learn how to
use it correctly and safely
- understanding and respecting the warnings
can prevent the risk of injury or damage to
the user, third parties, animals or property
and ensure that the bicycle is used in com-
plete respect of the environment
- preserve this manual carefully for future
consultations; if ownership of the EPAC bi-
cycle is transferred to other persons, this
user and maintenance handbook must also
be handed over
- documentation (User and maintenance
manual, EC Declaration of Conformity,
Warranty, etc.) is an integral part of the bi-
cycle, and must be preserved for the dura-
tion of its working life.
In case of sale or transfer of the bicycle,
hand over this documentation to the new
user
- in case of loss or damaging of this manual,
ask for a new copy to the Manufacturer or
Authorized Retailer.
- use the bicycle only after having received
and read the whole documentation careful-
ly
- the manufacturer reserves the right to
make at any moment and without prior
notice the necessary changes, due to
technical and commercial needs, without
obligation of retroactive communication.
ATTENTION
Like all mechanical compo-
nents, the EPAC is subject to
high wear and stress. Di󰀨erent
materials and components can
react to wear and stress fatigue
in di󰀨erent ways. If the fatigue
limit of a component is exceed-
ed, the latter may break caus-
ing injuries to the cyclist. All
the forms of cracks, scratches
or colour variations in highly
strained areas indicate that the
end of life of the component has
been reached and that the latter
should be replaced.
ATTENTION
In case of components built in
composite material with carbon
bres, the damages caused by
impacts can be invisible to the
user. It is necessary to regularly
inspect the fork or other com-
ponents made of carbon bre to
check for the presence of pos-
sible cracks, protuberances or
dents. Using a component with
cracks may lead to the complete
failure of the bicycle, with the
risk of serious injury or death.
Bici ELETTRICA_03-2022.indd 7Bici ELETTRICA_03-2022.indd 7 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 8
1.1.a Correct use
- The bicycle, subject of this manual, is
suitable for use on public, dirt or grav-
elled roads in good conditions and cy-
cling routes
- the use of the bicycle for purposes dif-
ferent from the intended one may lead
to dangerous riding situations, falls and
accidents. Short circuits may also occur
inside the battery pack with possible
consequent re
- ALWAYS use the bicycle as described
in this user manual and in the possible
integrative documentation.
1.1.b Non-compliant use
ATTENTION
Installation of any type of child
seat for transport of children is
absolutely prohibited.
- Do not add accessories not approved by
the manufacturer
- do not carry other people besides the rider
- never add equipment to the bicycle by
yourselves, nor try to modify it; rely on the
Manufacturer or on an Authorized Retailer
- possible errors committed during works not
carried out in a workmanlike manner may
cause damages to the bicycle and compro-
mise its operation and safety.
This may result in dangerous riding situa-
tions, falls and accidents
- the user can only carry out the operations
described in this manual
- thebicyclecannotbeusedo󰀨-roadorfor
jumps of any type
- it is absolutely prohibited to attach the bi-
cycle to a trailer or carriage of any type or
shape.
1.1.c Legal Regulations
- This manual provides indications and
instructions on the use of the bicycle
that add to, but do not replace, the lo-
cally applicable generic and/or specic
STANDARDS, REGULATIONS, PROVI-
SIONS or LAWS
- eachroadusermustfollowthetra󰀩cregu-
lations in force in the Country of use of the
bicycle.
It is possible to circulate with the EPAC on
roads and public streets only with the addi-
tion of the equipment prescribed by the law
of the Country of use of the bicycle.
1.1.d Residual hazards
- Fire hazard
Strong impacts due to improper use, stor-
age in overheated environments (e.g. in-
side a motor vehicle exposed to strong
sunlight), or falls may result in short circuits
inside the battery pack, causing it to catch
re.
ATTENTION
Motor vehicle cabins may over-
heat if exposed to strong sunlight.
High temperatures may result in
short-circuits inside the battery
pack, causing it to catch re.
Also, it is extremely important to
deate the bicycle tyres when trans-
porting it inside a motor vehicle.
Ensure you park in a shaded area
and that the ambient temperature
remains below 45°C.
• Use the bicycle only for the purposes it
has been designed for
• always store the bicycle in an environ-
ment where the temperature remains
between 0°C and +45 °C
• keep the bicycle away from heat sources
Bici ELETTRICA_03-2022.indd 8Bici ELETTRICA_03-2022.indd 8 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 9
such as heaters, radiators, stoves, etc.
• inthepresenceofsmokeoramesem-
anating from the battery pack, stop the
bicycleimmediatelyandputthereout
using an extinguisher, if available.
 Ifthereistheriskthatrespreadstosur-
rounding objects, promptly contact the
Fire Service.
- Electrical hazards
The use of non-compliant, damaged or faulty
battery chargers and electrical cables may
generate potentially lethal electric shocks.
• Always use the battery charger supplied
with the bicycle
• do not disassemble the battery pack or
the battery charger
• keep the bicycle and battery charger out
of the reach of children and animals
• ensure that the battery charger does not
come into contact with water or other liquids
• do not leave the battery pack or battery
charger where they may be exposed
to direct sunlight or heat sources (e.g.
heaters, stoves, etc.)
• never use the battery charger or the bat-
teries if they are damaged in any way
• never use the battery charger if insula-
tion on the cables or any of the plug con-
nections are damaged.
In that case, grasp the plug only in corre-
spondence of an insulated part.
- Generic hazards
• Do not move your hands, feet or other
parts of your body near the moving parts
of the bicycle (wheels, belts, pulleys).
Danger of injury
• in the event of rain, snow or slippery
road conditions, reduce your speed and
increase your distance from other vehi-
cles
• it is recommended to avoid water pud-
dles whose level may enter in contact
with the electronic parts of the bicycle
• do not leave the bicycle in a car, under
the sun.
ATTENTION
After along descent, the brake
discs may be very hot.
• Do not touch the brake discs imme-
diately after a descent. Let them cool
down at least 5 minutes before touch-
ing them.
To check temperature, it is enough
to touch the brake discs for a brief
instant with an unprotected nger. If
they are very hot, wait a few minutes
and repeat the test until when the
discs have cooled down.
1.1.e At rst use
HAZARD
Before using the bicycle, care-
fully read this use and mainte-
nance manual so as to familiar-
ize with the parts of the bicycle.
- Use the bicycle only in a seating position
suitable for you
- adjust position and height of the saddle
(see paragraph “Saddle adjustment”)
- completely recharge the battery pack (see
paragraph “Recharging the battery pack”).
Bici ELETTRICA_03-2022.indd 9Bici ELETTRICA_03-2022.indd 9 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 10
1.1.f Before every use
ATTENTION
An unsafe bicycle may lead to
dangerous riding situations,
falls and accidents.
- Before using your bicycle:
• check that the bicycle works correctly
and safely; take into consideration the
possibility that, while it was unattend-
ed, the bicycle may have fallen on the
ground or tampered with by strangers
• carry out a visual check of the bicycle
components (in particular the chassis
and the forks); if defects are detected,
immediately refer to the Manufacturer or
Authorized Retailer.
Only carry out the operations described
in this manual by yourselves. For all the
operations not described here, please
refer to the Manufacturer or to Author-
ized Retailer.
Use the bicycle only after restoring its
optimal conditions.
- If one or more defects are detected during
the inspections, immediately refer to the
Manufacturer or your Authorized Retailer.
Repair by yourselves the negligible defects
if in this manual are described the respec-
tive operations to be carried out
-
immediately refer to the Manufacturer or
Authorized Retailer if the operations for
repair of the damages are not described,
as it means that they cannot be carried out
autonomously, or in the event that the per-
formed operations has not produced the
desired outcome
- return to use the bicycle only when the lat-
ter is safe again
HAZARD
Danger of injury to ngers and
arms, danger of accident.
The bicycle may start inadvert-
ently due to the control opera-
tions.
Before every check, make sure
the electric motor of the bicycle
is deactivated. Visually check
that all the xing screw are
tightened correctly.
HAZARD
Visually check on every part of
the bicycle that there are no in-
cisions, breakages, deep cracks
and other mechanical damages.
If from the inspection emerges
the presence of defects, please
refer to the Manufacturer or Au-
thorized Retailer.
NOTE: Any tampering or damaging following
a fall won’t be considered as defects of the
bicycle.
- Even if not mandatory by law, it is ad-
vised to always wear an approved hel-
met.
1.2 CARE OF THE BATTERY
PACK
ATTENTION
An improper use of the lithium
batteries may cause res, ex-
plosions or chemical hazard.
- Only recharge lithium ions batteries with
the supplied battery charger.
Bici ELETTRICA_03-2022.indd 10Bici ELETTRICA_03-2022.indd 10 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 11
Do not recharge lead, NiCd-NiMh batter-
ies or accumulators
- do not charge the battery pack if it is hot.
The battery pack must be at ambient tem-
perature before charge
- immediately interrupt the recharge pro-
cess if the battery pack overheats; mini-
mum heating is normal
- do not put the battery pack in contact with
water or other liquids. If that happens,
do not use it and have it checked by the
Manufacturer or Authorized Retailer
- do not park the bicycle exposed to direct
sunlight: the battery pack may heat and
make the protection intervene.
1.3 WHICH OPERATIONS CAN
BE CARRIED OUT AUTON-
OMOUSLY BY THE USER
ON THE BICYCLE
HAZARD
The errors committed on the oc-
casion of works not carried out
in a workmanlike manner on the
bicycle may cause damages to
the latter, compromise its safety
of operation and void warran-
ty. This may lead to dangerous
riding situations, falls and acci-
dents.
- The operator must only carry out the opera-
tions described in this manual and for which
he has the appropriate tools available
- changing the characteristics of the single
components of the bicycle is not permitted.
1.4 SAFETY PROVISIONS
DURING USE
- The bicycle can be used in the traditional
manner or with the help of assisted ped-
alling.
NOTE: Before using assisted pedalling, it is
advised to familiarize with the use of the bi-
cycle.
- Use the bicycle only if you are able to
rmly control direction and braking at
high speed
- wear the helmet while using the bicycle
- drive carefully and prudently
- pedal in such a way as to always be
ready to brake
- do not drive under the e󰀨ect of alcohol or
drugs
- drive in such a way as to always have
full control of the bicycle and not to nd
yourselves in di󰀩culty in case of sudden
dangerous situations
- on wet surfaces, e󰀩ciency of the brakes
may reduce and braking distance in-
creases
- during the use of a bicycle it is oppor-
tune to only wear suitable clothing that
do not limit riding and do not block the
rider’s line of sight
- exclusively wear cycling tights. Loose
clothing may get caught in the bicycle
and cause serious falls
- in the dark and poor visibility conditions,
wear clothing with reective strips and
turn the lights on (if applicable)
- some clothing products and/or the use
of a backpack may limit the movements
of the rider
- it is advised not to wear high-heeled shoes .
- drive with prudence, respect the mainte-
nance intervals and immediately refer to
the Manufacturer or Authorized Retailer
in case of defects
- safety of the rider depends, among the oth-
er things, on speed and riding conditions.
The more riding is fast and rapid and the
conditions adverse, the higher the risk.
Please note that the roads may be dam-
aged and present obstacles, edges,
kerbs, undulations and similar. In these
zones, proceed with particular slow-
ness and care
Bici ELETTRICA_03-2022.indd 11Bici ELETTRICA_03-2022.indd 11 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 12
- the moving wheel groups may cause
injuries to hands and other parts of the
body.
Keep hands and other parts of the body
far from the moving wheel groups.
Make sure that hands and other parts of
the body of other persons (children or
adults) cannot enter in contact with the
moving wheel groups
- while riding, in particular in long trips and
in case of frequent breakages, the brake
discs may overheat in such a way as to
cause burns when in contact with the skin.
Do not touch the brake discs immediate-
ly after stopping, let them cool down for
at least 5 minutes before touching them .
Do not cool them by pouring water or oth-
er liquids; the discs may get damaged.
ATTENTION
The load worsens the perfor-
mances of the bicycle during op-
eration and increases the braking
distance.
- If the bicycle is overloaded, some of its
parts may even break or get damaged.
This may result in dangerous riding sit-
uations, falls and accidents.
Do not exceed the maximum permitted
load (130 kg) (cyclist + load).
1.5 PRECAUTIONS FOR
MOUNTING OF ACCESSO-
RIES OR COMPONENTS
FOR MODIFICATIONS
HAZARD
The addition of accessories and
components not approved for
your bicycle may cause damag-
es to the latter and compromise
safety of its operation.
This may dare result in danger-
ous riding situations, falls and
accidents.
The use of non-original parts is
considered tampering with the
bicycle which creates a risk for
the rider and immediately voids
the warranty.
- Do not add accessories or equipment to
the bicycle autonomously and do not try
to modify it.
 Formodications,alwayschooseacces-
sories and components together with the
Manufacturer or Authorized Retailer. As
regards the accessories and additional
weight they imply, also always consider
the maximum permitted weight of your bi-
cycle.
1.6 WHO CAN DRIVE THIS
EPAC BICYCLE
The rider of the bicycle:
- must be at least 15 years old.
- must be able to drive a bicycle, namely he must
possess base knowledge on the use of a bicy-
cle and be equipped with the necessary sense
of balance to drive and control the bicycle itself
- from a stationary position, he must be
abletohoponando󰀨safely.Thisapplies
in particular to ergonomic saddles if the
rider, from a seated position, is not able
to touch the ground with his feet
- he must possess a physical size suitable
for the bicycle and the maximum permit-
ted load must not be exceeded
- he must be physically and mentally able
tocirculateinroadtra󰀩c,especiallyifthe
rider desires to drive the bicycle on public
roads and streets
- he must possess the necessary endur-
ance to rmly control the bicycle for at
least two hours as the latter allows to
reach high speeds for long periods of time.
Bici ELETTRICA_03-2022.indd 12Bici ELETTRICA_03-2022.indd 12 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 13
HAZARD
The bicycle does not allow to
compensate for disability or
lack of physical tness.
1.7
WARRANTY CONDITIONS
By buying the assisted pedalling bicycle, the
user obtains a high-quality product designed,
assembled and built in Italy .
1.7.a Pre-requisites for the request for
warranty
The manufacturer guarantees the assisted
pedalling bicycle against manufacturing de-
fects or components failure for the following
periods of time (starting from the date of pur-
chase).
Legal warranty of 2 years on:
- malfunctioning and/or breakage of the bicy-
cle components (handlebars, brake levers,
pedals, suspension, drivetrain, etc.)
- electric motor
- display
- battery
Commercial warranty of 3 years (only valid for
therstowner)on:
- Chassis
- Fork
- Wheels
- CNC components
The components of the bicycle subject to
wear are excluded from warranty.
During the period of warranty, faulty components
shall be replaced or repaired free of charge.
The operations under warranty must be car-
ried out by the Manufacturer or Authorized
Retailer after receiving the approval of the
manufacturer.
The legal warranty and the respective con-
ditions can be transferred to possible subse-
quent buyers of the bicycle, notwithstanding
the duration of the warranty itself, starting
from the date of purchase.
The period of warranty starts from the date of
purchase and must be documented by specif-
ic invoice or till receipt.
The warranty does not cover possible mal-
functions of the components caused by nor-
mal use of the bicycle and wear (e.g.: tyres,
inner tube, belt, brake discs, etc.).
The owner of the bicycle is in charge of maintain-
ing and using it with care and ensuring that all the
advised maintenance interventions are carried out.
To request assistance, please visit an author-
ized retailer or write at:
emv[email protected]
1.7.b Exclusion from warranty
The warranty is not applied if the bicycle is used:
- for racing or sports competitions
- for commercial purposes (e.g.: rental).
The warranty is voided if the bicycle is used in an
non-compliantmannerorforapurposedi󰀨erent
from the one it has been designed for (see para-
graphs “Correct use” and “Non-compliant use”);
in particular, the warranty voids due to:
- insu󰀩cientorincorrectmaintenance;
- repairs not carried out by the Manufacturer
or Authorized Retailer
- absent or incorrect repair of worn or dam-
aged components
- malfunctions and/or breakage caused by
excessive or incorrect use.
The warranty is only valid if original compo-
nents are used, including those that have
been replaced.
Parts subject to wear, as well as the opera-
tions carried out by the retailers, are generally
excluded from the requests for warranty.
- The manufacturer reserves the right to
deliverand/or installcomponents di󰀨erent
from the damaged ones but with the same
qualitative and functional characteristics of
the replaced ones under warranty
- the use of the services under warranty
does not involve its extension beyond the
set duration (see paragraph “Pre-requisites
for the request for warranty”).
Bici ELETTRICA_03-2022.indd 13Bici ELETTRICA_03-2022.indd 13 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 14
1.8 IDENTIFICATION OF
THE BICYCLE
Identicationof thebicycleandofitsmain
components (motor and battery), occurs
through a QR Code located on the lower
side of the chassis.
To display the data, chassis the QR Code
using your smartphone camera and follow
the indications appearing on the display.
An additional label is located on the lower
part of the central steering column, indicat-
ing:
- acronym of the European Standard on
maximum speed of assisted pedalling
(25Km/h) and maximum power of the mo-
tor (0,25 Kw)
- crossed-out wheeled bin symbol that indi-
cates the obligation to dispose of the bicy-
cle as separate waste
- EC mark
Bici ELETTRICA_03-2022.indd 14Bici ELETTRICA_03-2022.indd 14 15/06/2022 17:07:5615/06/2022 17:07:56

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
1765 mm
680 mm
MAX 1080 mm
1125 mm
manual for use and maintenance EN - 15
2.1 OVERALL DIMENSIONS
Bici ELETTRICA_03-2022.indd 15Bici ELETTRICA_03-2022.indd 15 15/06/2022 17:07:5715/06/2022 17:07:57

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
manual for use and maintenanceEN - 16
2.2 TIGHTENING TORQUES
Normally, next to the screws to be tightened
is stamped the tightening torque which must
be used.
NOTE: if no other specic information has
been supplied by the Manufacturer, please re-
fer to the following tightening torques.
Threaded connection Threading Tightening torque (Nm)
Pedals 9/16” 34Nm
Handlebars connection screws M5 6Nm
Saddle connection M8 18Nm
Front wheel pin M12 x 1,5 10Nm
Rear wheel pin M12 x 1,25 23Nm
Bici ELETTRICA_03-2022.indd 16Bici ELETTRICA_03-2022.indd 16 15/06/2022 17:07:5715/06/2022 17:07:57

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION manual for use and maintenance EN - 17
2.3 TECHNICAL
DATA
ATTENTION
The manufacturer
reserves the right
to make changes
to the components,
without prior notice,
based on technical
needs and availabil-
ity of the component
on the market.
A-weighted sound pres-
sure level to the ears of the
rider and lower than 70dB
(A).
Component AMO R AMO RR AMO SV AMO XT PINION AMO RR PINION
Motor Mahle ebikemotion Technologies X series - Model X35 M1 +
Battery Mahle ebikemotion integrated 36V - 245Wh - Panasonic 18650GA
Chassis Aluminium - Size: S - M - L- XL
Front pulley Gates Carbon Drive - 55T Gates Carbon
Drive - 46 Gates Carbon Drive - 46T
Pedal cranks Miranda - 170mm Pinion - 170mm
Rear pulley Gates Carbon Drive - 20T Gates Carbon
Drive - 30 Gates Carbon Drive - 30T
Belt Gates Carbon Drive - 122T
Front brake Sram Level Magura MT4 Magura MT4 Sram Level Magura MT4
Rear brake Sram Level Magura MT4 Magura MT4 Sram Level Magura MT4
Front disc Sram 160 mm Magura MDR-C
160mm Magura MDR-C 160mm Sram 160 mm Magura MDR-C
160mm
Rear disc Sram 160 mm Magura MDR-C
160mm Magura MDR-C 160mm Sram 160 mm Magura MDR-C
160mm
Front tires Pirelli Cycl-e DT Sport 700x42C
Rear tires Pirelli Cycl-e DT Sport 700x42C
Wheels and spokes Carbon Wheels - Spokes Sapim Inox
Handlebars Aluminium and coned - D. 31,8mm - 22,2mm - L. 680mm
Saddle support tube Aluminium
- D. 27,2mm
Use Urban / Extraurban on paved, gravelled roads and cycle lanes
Front inner tube 700x35/43 - 48mm
Rear inner tube 700x35/43 - 48mm
Gearbox --- Pinion C1.6
(6 gears) Pinion C1.9
XR
(9 gears)
Bici ELETTRICA_05-2022.indd 17Bici ELETTRICA_05-2022.indd 17 28/06/2022 14:28:3528/06/2022 14:28:35

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
PINION
16
20
27
manual for use and maintenanceEN - 18
2.4 IDENTIFICATION OF
THE BICYCLE COMPO-
NENTS
1. Front wheel
2. Front disc brake
3. Front brake calliper
4. Front fork
5. Handlebars
6. Front brake lever
7. Rear brake lever
8. Left handle
9. Right handle
10. Handlebars connection
11. ON/OFF key
12. Seatpost collar
13. Seatpost tube
14. Saddle
15. Battery integrated in the chassis
16. Outlet for recharge of battery
17. Chassis
18. Electric motor
19. Motor pulley
20. Left pedal
21. Right pedal
22. Front pulley
23. Transmission belt
24. Rear wheel
25. Rear disc brake
26. Rear brake calliper
27. Speed change (Mod. Pinion)
28. Speed change control knob (Mod. Pinion)
continued
Bici ELETTRICA_03-2022.indd 18Bici ELETTRICA_03-2022.indd 18 15/06/2022 17:07:5815/06/2022 17:07:58

AMO R - AMO RR - AMO SV - AMO XT PINION - AMO RR PINION
PINION
10
18
5
8
2
1
7
3
19
17 6
9
11
14 15
25
26
4
21
22
23
12
13
24
28
manual for use and maintenance EN - 19
Bici ELETTRICA_03-2022.indd 19Bici ELETTRICA_03-2022.indd 19 15/06/2022 17:07:5915/06/2022 17:07:59