MVP AX-M60P User manual
REV:201509.01
TECHNICAL MANUAL
GENERAL
The AX-M60 planetary mixer is an advance design, highly reliable professional food processing tool,
and is ideal for mixing all types of dough as well as eggs, cream, mayonnaise, etc.
There are 2 speeds and various style attachments which can be selected. They are made of alloy
aluminum to meet with hygiene standard.
This model mixers is equipped with powerful 3 HP motors and strong gear drive design. The gears are
made of heat-treated alloy steel and a harnessed steel worm wheel.
If your operation and maintenance are correct, then it will give you years of service, and obtain the best
using result.
INSTALLATION
UNPACKING
Immediately before unpacking mixer, check it for possible shipping damage. If you find the packaging
material or the machine is damaged before unpacking, contact the carrier within 3 days of delivery.
Prior to installation, test the electrical service to assure it agrees with the specifications on the machine
data place located on the backside of the pedestal.
LOCATION
Place the Mixer in a convenient location, and allow working space on the hand-wheel or power bowl lift
switch side. All maintenance can be handled from this side, the top and the front. Set the mixer level
and use shims if the floor is uneven, the machined edge on the top of the transmission case makes an
excellent surface for leveling.
INSTALLATION, OPERATION AND CARE
OF MODEL AX-M60P
2
Electrical Connections (Cord Connected Mixers)
· Before making the electrical connections, read the specifications on the nameplate to
make sure that they agree with those of your electric service.
· Electrical connections should be made by qualified technician or electrician, who will
observe all applicable Safety Codes and the
National Electrical Code.
· Be sure the planetary runs in the direction
shown by the arrow in the planetary head.
Reverse direction is forbidden.
· To start motor, push ON button. The speed
selector handle must be at one of the
numbers indicating a speed, not at an
intermediate position.
On a 3 Phase Mixer, the installer must check the
mixing rotation of the planetary when the
electrical is connected.
3
4
OPERATION
WARNING: MOVING PARTS,
BEATER OR HOOK IN BOWL; KEEP
HANDS, CLOTHING, AND UTENSILS
OUT WHILE IN OPERATION.
All models are furnished with two
buon-switches, which control
power to the mixer.
The GEAR SHIFT LEVER (No.3) is
used to change speed. Always stop
the mixer before changing speeds.
To change speeds, turn the switch
OFF, move the gearshi lever to
the desired speed, and turn the
switch back ON.
·Speed 1 (low) – This speed
is for heavy mixtures such
as bread dough, heavy
baers, and potatoes.
·Speed 2 (medium) – This speed is for light dough which
must rise quickly, heavy baers, and some whipping
operaons.
DOUGH HOOK:
To install the dough hook (No 5), the bowl must be installed and
fully lowered. Place the hook in the bowl, push it up on agitator
sha, and turn it clockwise to seat the sha pin in the slot of the
agitator shank.
It is frequently used for heavy bread dough, and preferable to be
use at low speed.
The moisture content of heavy dough is a crical when selecng
nd
proper mixing speed. You should never use 2 speed when
mixing heavy dough with an Absorpon Rao (AR) of 50% or
less.
BOWL – CAPACITY: 60 QUART
New mixers bowls and dough hook should be removed and thoroughly washed with hot water and mild soap
soluon, rinsed with either a mild soda or vinegar soluon, and thoroughly rinsed with clean water BEFORE
being put into service. This cleaning procedure should also be done daily or aer each use.
The bowl must be installed before the agitator. To install the bowl, fully lower the bowl support. Posion the
bowl so the alignment bracket on the back of the bowl is in the bowl retainer and the alignment pins on the
front of the bowl support fit in the holes on the sides of the bowl.
ATTACHMENTS
To install an aachment, loosen the thumbscrew on the aachment hub and remove the plug. Insert the
aachment into the aachment hub making certain that the square shank of the aachment is in the square
driver of the mixer. Secure the aachment by ghtening the thumbscrew.
Move the gearshi lever to the desired speed and star the mixer to operate the aachment.
The meat and food chopper aachment should be operated in second or third speed. If material in the cylinder
stalls the mixer, stop the mixer at once. DO NOT aempt to restart the mixer in a lower speed – remove the
adjusng ring, knife, plate, and worm and clear the obstrucon.
5
MAINTENANCE
NOTE: All maintenance work should be done only aer unit has been disconnected from electrical power
and grounding.
CLEANING
Never use a metal or sff brush to clean mixer. Never clean the mixer with a water hose
or any fluid under pressure.
The mixer should be thoroughly cleaned daily.
Bowl and agitators should be removed from the mixer and cleaned in a sink.
The transmission case and planetary mechanism should be inspected weekly for leaks,
damage, etc. should it become necessary to repack the ball bearings; an authorized
service technician or the manufacturer should be contacted. Use of unapproved grease of
lubricants may lead to damage and void the unit's warranty.
The bowl li track should be lubricated semi-annually, or more oen under heavy usage. Disconnect the unit
from power supply before removing the top housing or apron. The drip cup (Fig. 1)? should be inspected
periodically for moisture or lubricant dripping. Remove the cup and wipe it with a so cloth.
DO NOT use a hose to clean the mixer – it should be washed with a clean damp cloth.
MIXING HEAVY DOUGH
The moisture content of heavy dough is a crical factor when selecng proper mixing speed. You should never
nd
use 2 speed when mixing heavy dough with an Absorpon Rao (AR) of 50% or less.
To determine the Absorpon Rao (AR) of a product, divide the water weight by the flour weight.
Example: Calculate the Absorpon Rao of a mixture containing 10 lbs. of flour and 5 lbs. of water.
10 ÷ 5 = 0.50 = 50% = AR
CAPACITY (QTS. LIQUID) 60 qt.
Egg Whites Wire Whip 2 qt.
Mashed Potatoes Flat Beater 40 lbs.
Mayonnaise (Qts. Oil) Flat Beater 18 qt.
Meringue (Qts. Water) Wire Whip 1.5 qt.
Waffle/Pancake Batter Flat Beater 24 qts.
Whipped Cream Wire Whip 12 qts.
Sheet Cake Batter Flat Beater 45 lbs.
Cup Cake Flat Beater 50 dz.
Layer Cake Flat Beater 70 lbs.
Pound Cake Flat Beater 55 lbs.
Sugar Cookie Flat Beater 100 dz.
Bread or Roll Dough (Light/Medium,
60% AR, =) Dough Hook 80 bs.**
Bread or Roll Dough (Heavy, 55% AR, =) Dough Hook 60 lbs.**
Pie Dough Flat Beater 50 lbs.
Thin Pizza Dough (40% AR, = , 5
min.max. mix time) Dough Hook 40 lbs.**
Medium Pizza Dough (50% AR, =) Dough Hook 70 lbs.*
Thick Pizza Dough (60% AR, =) Dough Hook 70 lbs.**
Raised Donut Dough (65% AR) Dough Hook 30 lbs.*
Whole Wheat Bread Dough (70% AR) Dough Hook 70 lbs.**
Egg & Sugar for Sponge Cake Flat Beater 24 lbs.*
* 1st speed ** 2nd Speed
* = If high gluten flour is used, reduce above dough batch size by
6
1
01
7
Description or Name Parts No. Qty
1 TOP COVER 11091-01-001A 1
2 RETAINER- MAIN SHAFT 1109S-01-002 1
3 RETAINER- TRANSMISSION SHAFT 1109S-01-003 2
4 GEAR HOUSE COVER 1109S-01-004 1
5 TRANSMISSION CASE 11100B-01-005 1
6 SUPPORT TO TOP COVER 1109S-01-006 1
7 SCREW S-C-1/2*1-1/4 2
8 SPRING WASHER 1/2" SW-1/2 6
9 COVER PLATE BM10-01-006 1
10 SCREW S+BR-1/4*3/8 1
11 BOLT 5/16*3/4 S-5/16*3/4 5
12 BOLT 3/8*1- 1/4 S-3/8*1-1/4 8
13 SPRING PIN 6*28 SPP-6*28 4
14 SPRING PIN 10*50 SPP-10*50 2
15 SCREW S-C-1/2*2-1/4 4
16 MACH SCREW 3/16*3/8 S+R3/16*3/8 4
17 OIL COCK 712-050 1
18 MACH SCREW 3/16*3/8 S+R3/16*3/8 4
19 BOLT 5/16*1/2 S-5/16*1/2 8
20 CONTROL PANEL 11091-01-011B 1
8
NO. PICTURE PARTS NUMBER PARTS NAME
1XL709-11A CONTROL PANEL W/BOX
2D11001R STICKER OF PANEL
3XL711-2-ROHS Power Board W/ BOX
4
MC HUO-11AK/2HP CONTACTOR-220V-3 PHASE
5Z-15GQ-B LIMIT SWITCH FOR GUARD
9
6Z-15GW-B LIMIT SWITCH FOR BOWL LIFT
7CABLE-12-3C-NEMA6-15P-UL POWER CABLE W/PLUG
8ABESMT44
EMERGENCY STOP (RED
BUTTON)
9ABMS800M LOCK NUT
10 ABAU8F01 SWITCH TERMINAL
(800F-X01)
11
C044M6L-AS-02 POWER INDICATOR
12
A010220PSR MAIN SWITCH
10
Description or Name Part No. Qty
1 AGITATING SHAFT 11100B-02-001B 1
2 GEAR(50T) 11100B-02-003 1
3 Resistance oil casing 11100B-02-004 1
4 Bevel gear 11193-02-006 1
4 WASHER 11193-02-006A 1
5 LOCK WASHER M55 1
6 LOCK NUT MN55 1
7 BALL BEARING 6207Z BR-6207 1
8 BALL BEARING 6010Z BR-6010 2
9 KEY KR-1/4*1/4*100 1
10 KEY KR-09*14*52 1
02
11
Description or Name Part No. Qty
1 GEAR SHAFT 11100B-03-001 1
2 GEAR(16T) 11100B-03-002 1
3 WASHER 11100B-03-003 1
4 CLUTCH COPPER BUSHING 11100B-03-004 1
5 GEAR(19T) 11100B-03-005 1
6 SHIFTING CLUTCH 11091-03-002 1
7 CLUTCH COPPER BUSHING 11100B-03-007 1
8 GEAR(32T) 11100B-03-008 1
9 KEY KRR-08*08*43 1
10 C- TYPE SNAP RING S25 STW-S25 1
11 WASHER 1100B-03-011 1
12 WASHER 11100B-03-012 1
13 BALL BEARING 6205 BR-6205 1
14 BOLT 3/8*1/2 S-3/8*1/2 1
15 SPRING WASHER SW3/8 1
03
12
Description or Name Part No. Qty
1 PULLEY 11092-03-001 1
2 GEAR SHAFT 11100B-04-001 1
3 GEAR(22T) 11100B-04-004 1
4 BALL BEARING 6206 BR-6206 1
5 C- TYPE SNAP RING S25 STW-S25 1
6 KEY 1/4*1/4*50 KR-1/4*1/4*50 1
7 KEY KRR-10*08*28 1
8 BALL BEARING 6205 BR-6205 1
9 LOCK WASHER M40*1.5P 1
10 LOCK NUT MN40 1
11 SPRING WASHER SW-1/2 1
12 NUT W1*12NF 1
04
13
Description or Name Part No. Qty
1 Motor Fixed Seat 11092-05-006 1
2 MOTOR PULLEY 11092-05-003 1
3 MOTOR 11092-05-005 1
4 BELT M7*1320 8
5 KEY 7*7*40 KR-7*7*40 1
6 SET SCREW 1/4*5/8 S-S1/4*5/16 1
7 BOLT 3/8*3/4 S-3/8*3/4 4
8 WASHER 3/8" W-3/8 4
9 BOLT 1/2*4 S-1/2*4 1
10 NUT NUT-W1/2"*12NC 1
11 BOLT 3/8*3/4 S-3/8*3/4 2
05
14
Description or Name Part No. Qty
1 GEAR (14T) 11093-06-001 1
2 CAP SCREW 5/16*1- 1/4 S-C-5/16*1-1/4 4
3 HUB ATTACHMENT 11093-06-002 1
4 ATTACHMENT HOLE PLUG 11091-06-004 1
5 THUMB SCREW 11031-06-005 1
6 BALL BEARING 2907 BR-2907 1
7 O SNAP RING P35 OR-P35 2
06
15
Description or Name Part No. Qty
1 CONTROL PANEL 1109S-01-006D 1
2 HUB & CAM ASSY. 1109S-07-013B 1
3 ECCENTRIC SHIFT SHAFT 1109S-07-003B 1
4 SHAFT FORK 11091S-07-004B 1
5 SHIFTER FIXED SHAFT 11091S-07-005B 1
6 BRACKET GEAR SHIFT 11091-07-006 1
7 HANDLE SEAT 11092-07-007 1
8 NUT 1/2*12NC NUT-1/2*12NC 1
10 COMPRESSION SPRING 11091-07-018 2
11 STEEL BALL 6 SB-6 2
12 SCREW S-C5/16*5/8 4
13 SPRING PIN 5*28 SPP-5*28 1
14 OIL SEAL TC38*50*07 OS-TC38*50*07 1
15 MACH SCREW 3/16*3/8 S+R3/16*3/8 4
16 SHIFT HANDLE KNOB 11091-07-012 1
17 SHIFT HANDLE 11091-07-001 1
18 SHIFTING CAM 11091S-07-008B 1
19 PLUNGER 11091S-07-009B 1
20 COMPRESSION SPRING 11091-07-010 2
21 SET SCREW 11091-07-011 2
07
16
Description or Name Part No. Qty
1 INTERNAL DRIVE GEAR(59T) 11091-08-001 1
2 CAP SCREW 3/8*1- 1/4 S-C-3/8*1-1/4 4
3 INTERNAL PINION (18T) 11091-08-003 1
4 RETAINER 11091-08-004 1
5 PLANETARY HEAD 11091-08-005 1
6 HEAD RING 11091-08-006 1
7 KEY 6*6*35 KR-6*6*35 1
8 AGITATING SHAFT 11091-08-008 1
9 TAPERED PIN 11091-08-009 1
10 OIL SEAL TC43*58*08 OS-TC43*58*08 1
11 OIL SEAL TC40*72*10 OS-TC40*72*10 1
12 BALL BEARING 6306Z BR-6306Z 1
13 BALL BEARING 6207Z BR-6207Z 1
14 CAP SCREW 3/8*1 S-C-3/8*1 1
15 WASHER 3/8" WB-3/8 1
16 MACH SCREW 1/4*5/8 S+R1/4*5/8 2
18 BOLT 1/2*3/4 S-1/2*3/4 1
08
17
Description or Name Part No. Qty
1 HINGE SCREW 11091-09-001 1
2 COLUMN BM60-09-002 1
3 SLIDEWAY 11091-09-003 2
4 BASE 11091S-09-004C 1
5 COLUMN COVER 11091-09-005 1
6 NUT 5/16*18NC NUT-5/16*18NC 2
7 BOLT 1/4*3/8 S-1/4*3/8 8
8 SPRING PIN 8*50 SPP-8*50 4
9 CAP SCREW 3/8*1- 1/2 S-C-3/8*1-1/2 12
10 BOLT 5/8*3 S-5/8*3 4
11 SPRING WASHER 5/8" SW-5/8 4
12 APRON AXM60-09-016 1
09
18
Description or Name Part No. Qty
1 BOWL CLAMP(LEFT) 11091-10-001A 2
1 BOWL CLAMP(RIGHT) 11091-10-001B 2
2 NUT 5/8*11NC NUT-5/8*11NC 4
3 BOWL SUPPORT 11091-10-003 1
4 BOWL RETAINER 11091-10-004 1
5 BOWL LOCATING PIN 11091-10-005 2
6 APRON 11091-10-006 1
7 MACH SCREW 3/16*1/4 S+R3/16*1/4 4
8 CAP SCREW 1/4*3/4 S-C-1/4*3/4 2
9 NUT 1/2*12NC NUT-1/2*12NC 2
10 SPRING WASHER 1/2" SW-1/2 2
10
19
11
20
Table of contents
Other MVP Mixer manuals
