MVP Axis AX-M12 Owner's manual

"
AX-M12
5659 Royalmount Ave.
Montreal, QC H4P2P9
Tel:[phone]
Fax:[phone]
12000 Biscayne Blvd. Ste 108
Miami, FL 33181
Tel:[phone]
Fax:[phone]
[e-mail] www.mvpgroupcorp.com

Installation, Operation and Care of
12 QT MIXER
+SA VE THESE INSTRUCTIONS +
GENERAL
This Mixer is an advanced design, highly reliable professional food processing tool, and is ideal for mixing
all types of dough, as well as eggs, cream, mayonnaise, etc.
This model Mixers are equipped with powerful. 1/2 HP motors and strong gear drive design. The gears
are made of heat-treated alloy steel and a hardness steel worm wheel. There are 3 speeds and various
style attachments, which can be selected to obtain the best using food, are made of alloy aluminum or
they're with hygiene standard.
A stainless steel safety guard is standard on model AX-M12.•
If
your operation and maintenance are correct, then it will give you years of service, and obtain the best
using result.
INSTALLATION
UNPACKING
Immediately after unpacking the mixer, check it for possible shipping damage. If this machine is found to
be damaged after unpacking, save the packaging material and contact the carrier immediately. Prior to
installation, test the electrical service to assure it agree with the specifications on the machine data plate
located on the backside of the pedestal.
LOCATION
Place the mixer in its operating location. Bench should be placed on a sturdy level surface. There should
be adequate space around the mixer for the user to operate the control and install and remove bowls.
Holes are provided in the base to permanently secure the mixer, although this not necessary in normal
installations. Floor models must be leveled front-back and side-to-side by sliding shims under the legs as
required.
1

ELECTRICAL CONNECTIONS (Cord Connected Mixers)
WARNING: THIS SUPPLY CORD ON THIS MACHINE IS PROVIDED WITH A THREE-PRONG
GROUNDING PLUG. IT
rs
IMPERATIVE THAT THE OUTLET TO WHICH THIS PLUG
rs
CONNECTED BE PROPERLY GROUNDED. IF THE RECEPTACLE
rs
NOT THE PROPER
GROUNDING TYPE, AN ELECTRICIAN SHOULD BE CONTACTED.
INSTALLATION DIAGRAM (mm)
388,5
Model No. Bowl Capacity
AX-M12 12 Qt.
co
'°
M
499
445
499
Motor for Agitator
0.5HP
2
l{)
'-1)
\J)
Agitator speeds
(R.P.M.)
515/262/146
ELECTRICAL
110V/60HZ/l PH

• I
OPERATION
WARNING: MOVING BEATER IN BOWL. KEEP HAND, CLOTHING, AND UTENSILS OUT
WIBLE IN OPERATION.
All models are furnished with an ON-OFF switch
(figure 1-11 ), which controls power to the mixer.
Figure 1
,.
The GEAR SHIFT LEVER (figure 1-3) is used to
change speeds. -Always stop the mixer before
changing speeds. To change speeds, tum the
switch OFF, move the gearshift lever to -the
desired speed, and tum the switch back ON.
•Speed 1 (low) -This speed is for heavy
mixtures such as bread dough, heavy batters,
and potatoes.
•Speed 2 (medium) -This speed is for light
·dough, which must rise quickly, heavy batters,
and some whipping operations.
O Speed 3 (high) -This speed is fast speed for
light work such as whipping cream, beating
eggs, and mixing thin batters.
AGITATOR
10
7
8
6
1 1
To install an agitator (figure 1-5), the bowl (Figure 1-6) must be installed and fully lowered. Place the
J agitator in the bowl, push it up on the agitator shaft, and tum it clockwise to seat the shaft pin in the slot
·] of
the agitator shank.
l
,:
DOUGHARM:
1 Frequently used for heavy bread dough, and preferable to be used at low speed.
;
i
speed. You should never use 2n
d speed when mixing heavy dough with an
The moisture content of heavy dough is critical when selecting proper mixing
'· Absorption Ratio (AR) of 50 % or less.

BEATER:
Commonly used for thin batters, cake and mashing potatoes, like stuffing and preferable
to be used at middle speed.
WIRE WHIP:
Best for whipping cream and beating eggs and preferable to be used at high speed.
BOWL
New mixer's bowl (Figure 1-6) and agitators (beaters, whip, and dough arms) should be thoroughly
washed with hot water and mild soap solution, rinsed with either a mild soda or vinegar solution, and
thoroughly rinsed with clean water BEFORE being put into service. This cleaning procedure should also
be followed for bowls and agitators before whipping egg whites with or whole eggs.
CONTROL PANEL (Figure 1-11)
ON-OFF�
4
eJ
I •I
TIMER

MAINTENANCE
NOTE: ALL MAINTENANCE WORK SHOULD BE DONE ONLY AFTER UNIT HAS BEEN
DISCONNECTED FROM ELECTRICAL POWER AND GROUNDING.
Never use a metal or stiff brush to clean the mixer. Never clean the mixer with a water hose or any
fluid pressure.
1,
The mixer should be thoroughly cleaned daily .
. ii
!I
i:
,*!
1 Bowls and agitators should be removed from the mixer and cleaned in a sink.
The transmission case and planetary mechanism
should be inspected weekly for leaks, damage, etc.
Should it become necessary to repack the ball bearings, an authorized service technician or the
manufacturer should be contacted. Use of unproved grease of lubricants may lead to damage and void the
. ' .. --
u :ut s warranty.
The
bowl lift slidways
(Figure 1-1) should be lubricated semi-annually, or more often under heavy usage.
Disconnect the unit from the power supply before removing the top housing or apron. The drip cup
(Figure 1-4) or safety guard should be inspected periodically for moisture or lubricant dripping. Remove
the cup and wipe it with a soft cloth.
CLEANING
The mixer should be thoroughly cleaned daily.
Bowls and agitators should be removed from the mixer and cleaned in a sink.
DO NOT use a hose to clean the mixer - it should be washed with a clean damp cloth.
The drip cup (Figure 1-4) should be removed periodically and wiped clean. A large flat blade screwdriver
may be used to remove the drip cup

z
u
-s:(
WIRING DIAGRAM
AC IN
AC IN
CONTROL
PANEL
CONTROL
PANEL
CONTROL
PANEL
.
CONTROL
. BOX
L.SW
SHIFT
L.SW
6
M1
LS2
LS2
LIFTER
L.SW
GUARD
L.SW