My Child On Board User manual

On Board
Instruction Manual
INSTRUCTIONS: Please read carefully and keep for future
reference. Your child’s safety may be affected if you do not
follow these instructions. Safety of your child is your
responsibility.
This product is tested to: BS EN 1888-1:2018
This stroller board is intended for children from 2yrs up to 20kg.
V3

page 2
Safety instructions
7. WARNING! Intended for use with children from 2 years old up to 20kg (44lb).
8. WARNING! Your child must step off the board before you attempt to:
- Go up or down steps, kerbs, stairs or escalators,
- Manoeuvre backwards,
- Go round sharp turns,
- Use the board on rough or uneven ground,
- Go onto soft surfaces e.g. snow, deep mud, soft sand, long grass.
9. WARNING! An adult must hold the pushchair handles tightly with both hands at all
times.
10. WARNING! Make sure your child is standing with both feet on the board before
pushing the pushchair.
11. WARNING! Check all connectors, arms and the wheels of the stroller board as
well as the pushchair before using it, and ensure that all connectors and locking
mechanisms are tightened prior to use.
12. WARNING! Do not use this stroller board if any parts are broken or missing or worn.
13. WARNING! Never let children play with the stroller board. When not in use, store
away from children’s access.
14. WARNING! Always disconnect your stroller board before folding your pushchair. On
some pushchair models you may need to disassemble the connectors as well.
15. WARNING! This product is only intended for one passenger.
16. WARNING! The board is only designed to be used if there is a child in the pushchair.
17. WARNING! The board must never be attached to the brakes, to any non-
loadbearing elements, or to any moving part of the pushchair.
This product complies with BS EN 1888-1:2018
Care and maintenance
Regularly inspect all locking devices and connectors before using the stroller board.
If you have any difculty with the wheels, ensure that dirt is not the cause.
Use a silicone based lubricant for the wheels.
Sponge clean with warm water and mild detergant.
Always allow to dry or use a cloth to dry before using or storing.
1. WARNING: Never leave your child unattended.
2. WARNING: Ensure that all the locking devices are engaged before
use.
3. WARNING: To avoid injury ensure that your child is kept away when
unfolding and folding this product.
4. WARNING: Do not let your child play with this product.
5. WARNING: Check that the pram body, pushchair body or seat unit
attachment devices are correctly engaged before use.
6. WARNING: This product is not suitable for running or skating.

page 3
Welcome
Thank you for purchasing the MyChild On Board.
Please read the instructions and warnings carefully before use to ensure safe and
satisfactory operation of this product.
Your child’s safety is your responsibility. If you have a query with this product or require
replacement parts, please contact the MyChild Helpline on 0161 335 2508.
Lay out the parts on a soft level surface and compare to the part/xings checklist
below. Do not discard any packaging until you are sure that you have all the parts.
WARNING! Assembly by an adult. Keep away from children until fully assembled. Keep
children clear during assembly as pack contains small parts which may present a
choking hazard.
Your 3 year warranty
Whilst we make and test our products to the highest standards of durability there’s
always a small chance of a hiccup! Our promise is to repair, replace or refund a
MyChild product that has an identied manufacturing defect from the date of
purchase for a full 3 years thereafter at no extra cost.
However, you must register within 28 days of the date of purchase to receive the full 3
years guarantee!
To receive your full guarantee you can register your product by:
visiting www.mychild.co.uk/warranty.html and complete the warranty form,
or by telephone on 0161 335 2508.

page 4
Contained in your carton are:
NoPart Qty
1 Board 1
2 Arms (left and right) 2
3 Connectors (left and right) 2
4 Wheels 2
5 Wheel housing washers* 2
6 Tubing adapters (for square tubing) 2
7 Storage strap 1
Parts checklist
*Washers may be pre-tted, loose (in the box) or in the sealed plastic bag
with the storage strap.
3 3
6 75
44
22
1

page 5
Assembly - Wheels
Assembly - Support arms
1. Place the On Board platform upside
down on a sturdy surface.
IMPORTANT: If the washers are loose in the
box, or in the bag with the storage strap,
place them into the wheel housing as
shown in the picture.
3. Loosen the screws so that the arms can
be easily inserted and adjusted.
4. Push the support arms in, but DO NOT
tighten the screws yet.
2. Align the wheels to the wheel housing
and push the wheels rmly into the
housing unit until you hear a “click”.
click

page 6
Assembly - Readying the connectors for tting (cont)
6. To get the connectors ready for tting on the pushchair, press the adjuster button (F)
and release the strap (E).
5. Connector parts:
(A) Tube protector.
(B) Block
(C) Body
(D) Quick release slider
(E) Strap
(F) Adjuster button
(G) Safety knob
(H) Tubing adapter (for square tubing)
A
B
C D
F
E
EFG
H

page 7
7. Unscrew the safety knob (G) until the block (B1) is fully retracted (B2).
The block (B2) should be ush with the body (C). If it is sticking out then push it in.
IMPORTANT: Ensure block (B2) is fully retracted. Failure to do so may make it more
difcult when tting to strollers with thicker leg tubing.
C
G
Assembly - Readying the connectors for tting (cont)
B2
B1
8. If you intend tting the connectors to
square or rectangular tubing then insert
the adapters (H) into the block (B) before
attaching the connectors.
H
B

page 8
Fitting the board - General tting advice
3. Loosen knobs (H). This will allow the two
arms (J) to be rotated and moved in or
out as necessary.
1. Attach the connectors to the legs
of the pushchair. Make sure both
connectors are at the same height and
pull strap (E) as tightly as possible through
the adjuster button (F) (you may need
to wiggle the connector left and right to
achieve this). Tighten safety knob (G) all
the way in ensuring block (B) is tightened
fully against the leg tubing.
2. For thin/narrow tubing:
• Slide the tube protector (A) to the body
of the connector (C).
• Pull the strap (E) through the adjuster (F)
as tightly as possible.
• Tighten the safety knob (G) fully.
ATTENTION! Ensure the connectors are
gripping the tube rmly before attaching
the board.
H
A
B
E
G
F
B
CG
JJ
IMPORTANT: Ensure block (B) is fully retracted. Failure to do so may make it more
difcult when tting to strollers with thicker leg tubing.

page 9
Fitting the board - General tting advice
4. Attach the arms to the connectors -
you may need to move the arms apart
or push them in so they are the correct
distance apart to t on the connectors.
Make sure the arms stick out from the side
of the board by the same distance on
both sides.
5. Adjust the board so it is level and
tighten the knobs (H) underneath the
board to x it into position.
ATTENTION: Make sure the board is
level and xed in position. Re-tighten if
necessary.
H
The On Board will t a wide range of strollers and pushchairs. This guide aims to provide
the steps for tting the On Board to some of the more common types of strollers and
pushchairs such as:
1. Large style umbrella folds,
2. Small style umbrella folds,
3. Doubles/Twins,
4. 3-Wheelers,
5. Classic frames,
6. Modern frames,
7. Tandems,
8. 3-in-1 chassis.
Locate the style of stroller/pushchair closest to the one you are wishing to t the On
Board to.
Fitting the board - To your model of pushchair

page 10
Fitting the board - LARGE-style umbrella fold strollers
Fitting the board - Small-style umbrella fold strollers