My Child F1 2-in-1 Baby Car Walker Go Go User manual

Go Go Walker
Instructions
IMPORTANT! KEEP FOR
FUTURE REFERENCE.
180418

1Safety Notes
CAUTION:
Read these instructions carefully before assembly and use and keep for
future reference. The child may be hurt if you do not follow these instructions.
WARNING:
The walker is not intended for babies that can already walk unassisted.
WARNING:
Do not use the walker if it is damaged or broken.
WARNING:
Do not use until the baby can sit upright by itself.
WARNING:
Clean friction components regularly to maintain stopping performance.
WARNING:
Never leave the child unattended. Always keep child in view while in walker.
WARNING:
Use only on at surfaces free of objects that could cause the walker to tip
over.
WARNING:
To avoid burns, keep the child away from hot liquids, ranges, radiators, space
heaters, re places etc.
Avoid serious injury or death. Block stairs/steps securely before using
walker.
Complies with ASTM F9077-12
WARNING -- STAIR HAZARD:

Page 3
1Safety Notes
IMPORTANT
- Adult assembly required.
- Read all instructions before assembly and use of the product.
- This baby walking frame is intended to be used by children who can sit unaided,
approximately from 6 months. It is not intended for children weighing more
than 12kg and/or more than 78cm in height.
- Take care when unpacking and during assembly.
- Dispose of all packaging materials carefully after assembly.
- Regularly check that all ttings remain tight. Tighten if required.
- Inspect the product before all assembly and periodically during use. Never use
this product if there is any loose or missing fasteners, joints or broken parts.
- Any additional or replacement parts should only be obtained from the
manufacturer or distributer.
- Never substitute parts.
ATTENTION! BATTERY SAFETY: KEEP FOR FUTURE REFERENCE.
BATTERIES NOT INCLUDED.
CAUTION: To prevent possible battery leakage, be sure to follow the guidelines
outlined below.
Alkaline batteries are recommended for longer battery life.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc) or rechargeable batteries.
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the toy before being charged.
Rechargeable batteries are only to be charged under adult supervision.
Only batteries of the same or equivalent type as recommended are to be used.
Batteries are to be inserted correctly by matching the + and - polarity markings.
Exhausted batteries are to be removed from the toy.
The supply terminals are not to be short-circuited.
Dispose of exhausted batteries properly.
Remove batteries when product is stored for long periods of time.
- Use a small Phillips-head screwdriver to open the battery compartment door
on toy.
- Insert the battery as indicated inside the battery door and re-attach the
battery compartment door with screw.

Page 4
2Parts List
A x 1
walker
B x 1
toy tray
C x 1
seat unit
D x 6
anti-slip pad
E x 2
directional wheel
F x 2
universal wheel
G x 6
screw
H x 1
ower
screw driver
not included
2 x AA batteries required
(not included)

3 Assembly
Page 5
1. Unpack all contents and check that all parts are present before starting
assembly. Please refer to parts list.
Place walker (A) on a solid at surface with bottom of base facing upwards.
Insert the pins of the universal wheels (F) into their housing located at the front
of the walker. Press until they click into place.
Insert the directional wheels (E) into their housing located at the rear of the
walker. Ensure to align shape of mount with housing before inserting wheels.
Press until they click into place. Pull on wheels to ensure they are properly
inserted.
WARNING! Ensure you have installed wheels correctly before continuing.
x2
universal wheel directional wheel
x2
2. Align the anti-slip pads (D) to their attachment points on the baby walker
base. Insert screws (G) into located hole and tighten screw with a screw driver.
Repeat until all 6 anti-slip pads are assembled.
anti-slip
pad
x6

x8
4 Assembly
Page 6
3. Push the crotch portion of the seat unit (C) inside out to form the seat.
IMPORTANT. The pattern fabric should be on the inside of the seat unit.
Insert the 8 tabs located on the seat unit into the slots dotted around the seat
ring.
tab
seat unit
4. Turn walker upside down and pull tabs rmly from underneath walker until
tabs are completely through slots. Fix tabs to the plastic hooks located on the
underside of the walker top tray. Ensure all tabs are secure before continuing.
IMPORTANT. Push down rmly on seating area of seat unit to ensure it is
securely assembled.
WARNING! Ensure you have installed seat unit correctly before continuing.
x8
hook

4Assembly
Page 7
4. Raise the baby walker top tray as shown until it clicks into place.
Note. the baby walker has 3 height positions.
3
2
1
5. The toy tray (B) requires 2 x “AA” batteries (not included). Use a screw driver
to unfasten battery cover. Insert batteries. Secure battery cover back into
position.
WARNING! Remove batteries before storing the toy tray and walker.
Once batteries are installed, attach the toy tray to the walker. The tray will
click when secure.

6. Once batteries are installed, attach the ower (H) to toy tray (B). Press rmly
until ower is secure.
Attach the toy tray to the walker. Turn the clips located on the underside of the
walker lengthwise to lock toy tray. To release, turn the clips 90°.
locking clips
2
3
4Assembly
Page 8
5 Toy Tray
Press the various buttons for sounds and melodies.
The music will stop automatically.
1

6 Height Adjustment
Page 9
The baby walker has 3 height positions. To adjust height, remove baby from
walker. Turn the safety button lengthwise and press the safety button up until
the mechanism is released. Adjust to desired height.
WARNING! When the position has been selected, check the safety button
is turned 90° to prevent accidental release.
WARNING! Do not adjust height when baby is in the walker.
WARNING! Ensure mechanism is locked before placing baby in the walker.
12
To fold walker, turn the safety button lengthwise and press the safety button up
until the mechanism is released. Push walker down to a folded position.
1
2
3

Seat pad: Hand wash or spot clean. Use mild soap or upholstery shampoo.
Wash separately. NEVER use bleach. Dry in shade thoroughly before reuse and
avoid direct heat and sunlight. Do not iron. Do not dry clean.
Frame: Wipe frame with soft clean cloth and mild soap. NEVER use bleach.
NEVER use abrasive, ammonia based, bleach based or spirit type cleaners.
Store walker in a dry location away from any heat sources, and not in the sun.
Ensure the product is fully dry before use or storage.
This product requires regular maintenance to keep it in good working order.
Regularly check all parts of the product to ensure that they are operating
correctly and for signs of wear or damage.
Do not use this product if any part is broken, torn or missing and use only spares
provided by the manufacturer.
The crossed bin symbol on the appliance indicates that the product at the end of its life, must be disposed of separately from domestic waste, either by taking it to a separate waste
disposal site for electric and electronic appliances or by returning it to your dealer when you buy another similar appliance. The user is responsible for taking the appliance to a
special waster disposal site at the end of its life. If the disused appliance is collected correctly as separate waste it can be recycled, treated and disposed of ecologically. This avoids
a negative impact on both the environment and health and contributes towards the recycling of the product’s materials. For further information regarding the waste disposal
services available, contact your local waste disposal agency or the shop where you bought the appliance.
7 Maintenance
Page 9
8 Cleaning

IMPORTED BY
TARGET AUSTRALIA PTY LTD.
12 THOMPSON ROAD,
NORTH GEELONG,
VIC 3215
AUSTRALIA.