MyBones Marodyne LiV User manual

Before using your Marodyne LiV device, please familiarise yourself with
the ‘Instructions for Use’ guide enclosed with your device
Connect the power cord into the
switching adaptor
Plug the power cord into the
back of the device
Connect the AC power plug into
a mains power socket. A green
light will display on the power
brick to indicate the device is
receiving power
Switch the device on using the
rocker switch located at the
back of the device. A blue light
will signal it is successfully
switched on
V4 - 14/07/2022
Place your device on a dry, hard
and level floor (e.g. a tile/stone
floor or a thin carpet)
Ensure the device is positioned
where you intend to use it.
When the device is powered on,
it must not be moved
Do not wear shoes while using
the device. It is recommended
you wear socks
Step onto the device from the
back and place your feet
approximately shoulder width
apart. It is recommended you
stand on the device with your
big toes in line with the bottom
of the Marodyne LiV logo
Once the calibration is
complete, the word ‘Go’ will
display on the device and a
beep indicates it’s ready for
use. A single green light at the
centre of the feet indicates the
device is in standby mode, and
you can begin your session
When switched on, the device
will undergo a series of light
cycles as it calibrates

Once your 10-minute session is
complete, step off the device
The device will automatically
enter a standby mode
Use the switch at the rear of the
device to turn it off between
sessions
If you are sharing your device,
leave the device for 15 minutes
between sessions to recalibrate
Do not move the device whilst it is in
standby mode. Ensure your
Marodyne LiV device is turned off at
the rocker switch first**
Always turn your Marodyne LiV
device off using the rocker switch
first before switching it off at the wall
When shipping or transporting the
device, always ensure it is in the
travel case provided, and the
protective foam band is fastened
securely around the sides of the
device, tucked just below the
platform rim
** if you have moved the device
whilst in standby mode, switch it off
at the rocker switch, and then switch
if off at the wall. Leave the device for
15 minutes before turning it back on
Correct foot
placement
Once you step onto the device,
it automatically calibrates to
your weight and starts to
vibrate gently
When you are standing correctly
on the device you will feel the
gentle vibrations in your jaw
A timer on the device’s display
will count down from 10 minutes
to indicate how much time is left
of your session
If you step off the device the
timer will automatically pause
(This takes a few seconds). You
have 5 minutes to step back
onto the device before the timer
resets and the device re-enters
standby mode
An orange light or ‘BAL’ message
on the display indicates you
need to correct your balance. An
alarm may sound, but there is no
need to step off the device. If
you do not correct your balance,
an 'Eror' message will appear on
the display. Step off the device,
and restart by turning off the
rocker switch. Wait a minute
and switch it on again
The device will emit a short
beep when your 10-minute
session is complete

You should not wear shoes, only socks while using the device
A single green light in the centre of the display will indicate you are
positioned correctly. You should feel the vibrations all the way up to your
jaw
If you remain completely still for too long, the sensors in the Marodyne
LiV device may interpret that you have stepped off and the device will
go into standby mode. Shift your weight from side to side or rock gently
back and forth to restart the vibrations
Stepping off the device and stepping back on again should restart the
vibrations
Please ensure that you are correctly positioned on the device as per the
user manual
The level of vibration does not change from 0.4g at 30hz as the device
calibrates to the weight of each user. The intensity may feel different
depending on your positioning on the device
Incorrect posture or balance may cause the device to emit a mechanical
rumbling noise. To stop the noise, adjust your posture and balance
slightly
It's best to position your device somewhere easily
accessible so you can use it every day without
the need to move it

User is leaning
or standing too far
to the left
User is leaning
or standing too far
to the front
User is leaning
or standing too far
to the right
User is
well-positioned
User is leaning
or standing too far
to the rear
The yellow lights indicate you are distributing your weight unevenly. The
lights show you how to adjust your stance. See the diagram below for an
explanation of what each light indicates:
When transporting the device, ensure the device is stored flat in its case
with the protective foam band fastened securely around the sides of the
device, tucked just below the platform rim. If you are taking your device
on a plane, ensure the device is in your hand luggage and secured flat in
an overhead locker. Putting your device in the hold of an aircraft will
negate the warranty
V4 27/07/2022