MyCharge Voyage 1000 User manual

Owner's Manual
myCharge name, logo and Voyage are trademarks of RFA Brands. Patent
Pending. Bluetooth is a registered trademark owned by Bluetooth SIG, Inc.
©2012 RFA Brands. All Rights Reserved.
Made in China. IB-RFAM0206

2 3
Thank you for
choosing myCharge
Voyage™ 1000

4 5
Thanks for choosing myCharge.
In The Box
• myCharge Voyage
• Lanyard
• Owner’s Manual
• Warranty Manual
Section I: Quick Start
1. Charge up your Voyage by plugging it into a USB power
adapter or computer. As Voyage charges, LEDs on
the unit will sequentially illuminate. When the unit is fully
charged, all LEDs are lit. Press the level check button to
see how much power is available.
2. Connect your device to the Micro-USB connector.
3. Unplug your device when it’s charged and go! Your
Voyage will automatically power off after your device is
unplugged.
Section II: Charging Voyage
To charge your Voyage, connect it to a USB power source
(USB-A to wall adapter, notebook USB port) with the on-
board green USB input cable. Times to charge the Voyage
vary based on what it’s plugged into. You can expect a full
charge from a USB adapter in about an hour and a half, or
from a standard notebook USB port in about two and a half
hours.
Note: It is normal for your Voyage to be warm to the touch
while in use.
OUT
USB Charging
Cable
Multifunction
Button
Micro-USB
Connector
LEDs
Charge from a USB power adapter or your computer

6 7
Section III: Charging Devices
Voyage uses an automatic device detection system. When
a device is plugged in the Voyage provides charging power
until it is unplugged or the Voyage runs out of energy.
The Voyage Micro-USB connector is compatible with
the majority of mobile devices including smartphones,
Bluetooth headsets, portable navigation devices, MP3
players, and more.
Section IV: Checking Battery Level
To check how much energy is available, press the level
check button. LEDs next to the button will illuminate
indicating approximately how much energy is available for
use.
LED 1 Flashing: Under 20%
LED 1: 21-40%
LED 2: 41-65%
LED 3: 66-90%
LED 4: 91-100%
Section V: Sound Mode
Voyage has built-in tone capability. Tone mode will audibly
inform you when devices are plugged in or disconnected,
and when the unit is charging or has completed charging.
To disable, enable and/or change the sound mode
1. Locate the Sound pinhole button under the green USB-A
cable
2. Plug Voyage into your PC
3. Use a paperclip to cycle Tone Silent
If you prefer no sound toggle to the silent mode - unit will
make no sound when this option is selected. If you prefer
tone mode toggle until you hear the tone.
Sounds

8 9
Section VI: Lanyard Strap
Your Voyage includes a lanyard
strap for easy portability. To affix
it to Voyage, slide the skinny loop
of the strap under the rod in the
opening, then pull the thick strap
through the loop.
Section VII: Maintenance
To keep Voyage operating at its full potential, please do the
following:
1. Re-charge every three months when not in use.
2. Keep dry and away from moist and corrosive materials.
3. To clean, wipe surface with dry cloth.
Section VIII: Product Specifications
Battery: 1000 mAh Lithium Polymer
Input:
USB-A: 5 VDC, 1.0 A
Output:
Micro-USB: 5 V, 1.0 A
Total Output Current: 5 V, 1.0 A
Section IX: Troubleshooting
My device is not charging: Confirm that your device
is properly connected to the Micro-USB connector and
the Voyage itself has energy (by pressing the level check
button). LEDs indicate how much energy is available for use.
If the Voyage has energy and your device is not charging,
unplug it and plug it back in. If this still doesn’t work, use
your device cable to make sure the device is working
properly.
I don’t want the tone function on: Refer to Section V:
Sound Modes.
For additional troubleshooting information and device
compatibility, please visit: www.mychargepower.com

10 11
RFA Brands Service Center
Telephone: [phone]
Hours: 8:30 AM – 7:00 PM (ET)
Monday - Friday
E-mail: [email protected]