mychway HR-BX001 User manual

- 1 -
—Please read the instructions before use！
USER MANUAL

- 2 -
Ⅰ.Brief Introduction
E-light applies three core technology, IPL, RF, and epidermis cooling. It
combines the advantage of IPL and RF, in one hand, the skin absorbs IPL energy
selectively, and the skin also absorbs RF energy, on the other hand, the
RF-surface-touch cooling technology removing the discomfort and complications by
high heat of IPL. Therefore, the effect and safety of E-light makes a breakthrough.
1. Principle
Applying the technique of IPL and Bi-polar Radio Frequency, the equipment
acts on the entire skin corium and connective tissue, stimulates the collagens of
different depth to realign and grow, then gets treatment effect. Bio-polar RF release
energy at the same time, with the selective absorption for the skin to light energy,
various pathological tissues of corium and epidermis creates Photothermolysis effect.
Since light energy is far below conventional IPL, the pigment tissue and vascular
pathological tissue of the corium and epidermis would absorb more energy without
injuring the epidermis, and then remove these pathological tissues better and get
the effect.
2. Application：
1. Hair removal (including dark skin);
2. Skin rejuvenation
3. Acne treatment;
4. Removing freckle, age spots, sun spots, pigmentation troubles, etc;
5. Removing red face, red capillary, and bottle nose.
3. System Self-checking
The circuit of system entering the self-checking situation when the machine
starts, leave the machine carry on the self-checking for 5-10 seconds, then continue
the operation.
4. System Classification
Electric shock protection：Grade1
BF Grade

- 3 -
Corrosion prevention liquid：ordinary
Do not use the machine in the environment mixed of flammable narcotic and air or
nitrogen oxide mixture.
5. Equipment Consist, Specification, & Accessory List
1. Equipment Consist:
1.1. Mainframe
A. Power supply system
B. Microcomputer system
C. Monitor
D. Cooling System
1.2. E-light Handpiece
A. Intense pulsed light source, xenon lamp
B. Reflector and filter
C. Sapphire wave guide
2. Technique Specification
●IPL Power: 800W
●RF Intense Electric Energy: 5MHz
●Light Energy: 1-50J/cm2
●Pulse Amount: 1-6
●Pulse Width: 1-10 ms
●Pulse Delay: 1-100 ms
●Repeat frequency: 1-4s
●RF working time: 50-2500 ms
●Spot size: 8x40mm
●N.W.: 35kg
●Voltage: 110V~220V±10%, 50~60Hz

- 4 -
3. Equipment Structure

- 5 -
4. Accessory List
No.
Item
Unit
Qty
Remark
1
Main frame
set
1
in the main case
2
E-light Handpiece
pc
1
in the lateral foam box
3
RF Handpiece
pc
1
in the lateral foam box
4
Filters
pc
5x2
in the filter box
5
Power Lead
pc
1
in the lateral foam box
6
Key Switch
pc
2
in the filter box
7
Goggles for Operator
pair
1
in the lateral foam box
8
Goggles for Patient
pair
1
in the lateral foam box
9
Spare Plugs & fuses
pc
2
in the lateral foam box
10
Water funnel
pc
1
in the lateral foam box
11
User Manual
pc
1
in the lateral foam box
Ⅱ.Standard Treatment Process
2.1 Form filling
Fill in the blanks of the Client File, confirm the treatment program, and remind
the client pay attention to some points before and after treatment.
2.2 Face cleaning
Clean the face with gentle face cream for 3 minutes.
Remind: clean the hands of operator and the handpiece with
bromogeramine.
2.3 Preheating
Start the equipment after face cleaning; preheat for not less than 3
minutes (without lighting the xenon lamp).
2.4 Shaving
Shave the unwanted hair of the treatment area(2 minutes).
2.5 Gel coating
Coating the gel evenly (2-3mm) on the skin.
Effect：light guide, cooling, anaesthetisin.
Attention: no coating on eyes, eyebrows, lips.
2.6 Eye protection
Operator: wear the safety goggles.
Patient: close the eyes, wear professional safety goggles or cover the eyes with
eye patch.
2.7 Allergic test

- 6 -
Emit 2 or 3 light spots in the bottom of ears in safe parameter, observe for 3
minutes.
Effect: do not continue to operate if there is an allergic phenomenon.
2.8 Operation
Carry on the operation with a suitable parameter to the patient.
ATTENTION:
2.8.1 Inform the patient that there will be a slight pricking in operation before
operating, to avoid panic.
2.8.2 Start the operation with a low energy grade; adjust the parameters in operating
while asking the feeling of the patient.
2.8.3 Move the light spot by one spot overlapping the upper 1/3 part of the previous
spot.
No emitting one area repeatedly, otherwise may cause inflaming or burns.
2.8.4 The handpiece should touch the skin vertically, no over pressing or leaving the
skin.
2.8.5 Observing the reaction of skin while operating.
2.9 Cold compress
Keep gel coating for 20 minutes after operation ending; carry out cold compress
in obvious slight reddish reaction till reddish fading away.
2.10 Cleaning
Clean the gel with cold water, coat corresponding cosmetics.
2.11 Treatment Course
Skin Rejuvenation Program: 30-45 days/time (4 times/course)
Hair Removal Program: 2-3months/time (3times/course)
2.12 Special reminding
2.12.1 Ask the client before treatment: is there a allergic or not; is there a bad
reaction before for similar operation; fill the Client File concretely. Adjust the
parameters on the basis of full acquaintance concretely. Adjust the parameters on
the basis of full acquaintance of the condition of patient. Inform the patient the
possible reaction in operation before operating.
2.12.2 In large area treatment or long time continuous operating, the water inside
the equipment will warm up and the handpiece will be hot, interrupt the operation
to refresh the water or leave the water cool down to continue operating.

- 7 -
2.12.3 Refresh the circulating water in one month; use purified water or medical
distilled water.
Ⅲ.Operation Instruction
3.1 Before starting the machine
3.1 Accessories connecting：
3.1.1 Connect the handle and filters:
3.1.1.1. Put the E-light handle on the hanger
3.1.1.2. Connect the E-light handle to the connecting port on the back board of the
machine tightly.
3.1.2 Check the water holes of the backboard, make sure the water outlet hole is
plugged well.
3.2 Water infusing:
3.2.1 Connect the funnel with the affussion and open the overflow hole
3.2.2 infuse water till water spill out from the overflow hole continously
3.2.3 Take out the funnerl and take back the cap of the overflow hole .
3.3 Checking
3.3.1 Make sure there is no water leaking;
3.3.2 Make sure there is no moisture or wet for electricity connecting parts;
3.3.3 Make sure the key switch is in the off position;
3.3.4 Make sure the emergency stop switch is in the on position.
3.4 Starting the equipment
3.4.1 Connect the power cord, turn on the key switch;
3.4.2 Double confirm there is no leaking of water circulation, fold the protective
cover by turning it right.
3.5. Debugging
3.5.1. Make sure water and electric circuit is correct connected; then turn on
the power to start the machine.
3.5.2. Turn on the master power switch on the backboard;
3.5.3.Turn on the emergency switch (clockwise turn) in the front side of the
mainframe
3.6. Operation
Enter operation condition after debugging and no abnormalities found.
3.6.2. Treatment Program Selecting Interface
Welcome Interface

- 8 -
There are 6 treatment programs that could be selected:
a. Hair removal
b. Skin rejuvenation
c. Pigmentation Therapy
d. Vascular Therapy
e. Acne Therapy
f. RF: Wrinkles Therapy
Select different treatment programs by clicking.
3.6.3. Treatment Program Operation Interface

- 9 -
current treatment program
3 different groups of saved parameter setting.
Click , system will enter into the saved parameters of mode 1
IPL energy display
Click and to increase or decrease IPL energy.
RF energy adjusting
cooling degree adjusting
Pulse1：working time of the first pulse, 1-10ms adjustable.
Pulse 2 and Pulse 3：sub pulse width, 1-10ms adjustable.
Delay1: 1st pulse delay, interval between the 1st pulse and 2nd pulse.
Delay 2 and Delay 3: interval between two pulses.
RF working time, 50-2500ms adjustable.
Pulse amounts
interval between two spots, 1-4s adjustable.
back
water circulating status

- 10 -
lamp status
charging status
counter of shots for the current treatment
standby, click standby, the lamp will be lightened off. Click standby when
treatment finish to turn off the handle
ready, click ready, the lamp of the handle will be lightened up, and light
will be simmered by press the button on the handle
3.6.4. RF Operation Interface
3.6.4.1 Usage of RF handle.
a. Coating the gel evenly (1mm) on the treatment area.
b. Chose different probes for different treatment area.
15mm: eyes, 20mm: forehead, face; 30mm: face, body
c. cling the probe to the skin rightly.
Attention:
a. Do not press the blue button before the probe clinging the skin.
b. Both of the two polars (two parts on the probe) must cling the skin together when
operating.
c. When the operation finishes, release the blue button first, then move the probe out of the skin.
3.6.4 System Setting interface