Mytee Contractor's Special 2000CS Firmware update

1
Instructions for
Contractor’s Special™ 2000CS/2001CS
13655 Stowe Dr., Poway, CA. 92064
Model #
Serial #
Form # ADM-CS
1-15
Please read before use.
Register your product
at www.mytee.com/help
2000CS p.2
2001CS p.8
General & Maintenance information p.14

2
2000CS FRONT
CONTRACTOR’S SPECIAL™ 2000CS
2000CS BACK
2000CS ACCESSORIES
1. Waist high controls
2. 2” Male Cuff-Lynx™
3. Female QD
4. Solution tank
5. Front vent
6. Solution lid
7. Push handle
8. Recovery tank lid
9. 3” casters
10. 8” wheels
11. Rear vent
12. 25’ Power cord
13. Bucket-high drain valve
14. Recovery tank
8300 EZ C - 1 2” Wand
4
2
5
9
H226 - Drain Elbow
8501- 15’ 1-1/2” Vac/Sol Hose
H141 - 1 1/2” Cuff-Lynx™
1
3
6
7
10
13
REPLACING HOSE CUFFS WITH CUFF-LYNX™
Once you receive your Contractor’s Special™, you will need to
replace the cuffs on your vacuum hose. To remove old cuffs, twist
clock-wise. To attach reducer Cuff-lynx™ to vacuum hose twist
counter clock-wise.
Twist clock-wise to remove standard cuffs.
Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.
8
11
12
14

3
CONTRACTOR’S SPECIAL™ 2000CS
2000CS ATTACH HOSES
Firmly attach hose and quick disconnect. Make sure quick discon-
nects snap together rmly. Once attached to unit connect Q.D. to
upholstery tool. Always inspect hoses for cracks or fraying.
2000CS VACUUM & PUMP
To use vacuum, turn on vacuum. To use pump, turn on pump.
VACUUM PUMP
2000CS FILL SOLUTION TANK
Lift lid to ll. For best results, ll with warm water (140o F).
ATTACH VAC & SOLUTION HOSE TO WAND
Attach hose cuff to end of wand tube. Attach female QD to male
QD located near the wand trigger.

4
CONTRACTOR’S SPECIAL™ 2000CS
2000CS SYSTEM MAINTAINER2000CS ADDING DEFOAMER
Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Contractor’s Special™ vacuum motor .
2000CS RECOVERY DRAIN
When the oat shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.
2000CS LOCKING CASTERS
Locking casters help keep the machine remain stationary during
use.

5
CONTRACTOR’S SPECIAL™ 2000CS PARTS & PRICING
Items Not Shown
Accessories
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
P756
base, firebird
1 $147.99
2
H216
nut, lock, 1/4-20, nylon insert, s/s
12 $0.99
3
H210
washer, 1/4" flat, s/s
18 $0.99 ea
4
H667
caster, 3", Black Hub, Gray Tread
2 $14.99 ea
5
H342
bolt, 1/4-20 x 1" hex head, s/s 8 $0.99
6
H213
washer, 1/4" lock, s/s
4 $0.99 ea
7
H296
guard, cooling fan, wire
2 $2.99 ea
8
H343
screw, #10 x 5/8" hex head, zinc
9 $0.99 ea
9
C305
pump, 120psi, demand, 115V
1 $151.99 ea
10
B172
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
1 $9.49 ea
11
PH615-26
sol hose, 1/2" kuri, 100 psi
1
$8.99/ft
12
B160
adapter, brass, 1/2" barb x 3/8" fsw, ball end
1 $3.49 ea
13
H347
clamp, hose, 5/16-29/32
4 $1.99 ea
14
H222
screw, #10-32 x 1-1/4" phil pan head, zinc
4 $0.99 ea
15
H273
nut, kep, #10-32 zinc
4 $0.99 ea
16
B105
bushing, brass, 3/8"mpt x 1/4" 1 $3.19 ea
17
B136
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
1 $4.99 ea
18
AH108S
sol hose, 1/4" x 24 1/2", (OAL)
1 $26.49 ea
19
H202
bolt, 1/4x20x3/4" hex head
3 $0.99
20
H768
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
5 $0.99 ea
21
H330
plate, single manifold, 6.5" x 9"
1 $7.99 ea
22
H501
vac support, 3 stage, 4-1/16"
3 $4.99 ea
23
P735
manifold, single vac, no gasket
1 $14.99 ea
24
G004
gasket, vacuum motor
1 $8.99 ea
25
PH627-24
vac hose, 1-1/2", black, wire reinforced
1
$6.49/ft
26
H300
cuff, black 1-1/2"
1 $5.99 ea
27
H217
clamp, hose, 2-1/4 dia
2 $1.49 ea
28
G059
exhaust boot, plastisol
1 $4.99 ea
29
C302 vac motor, 3 stage, 120V, tangential
1 $139.99 ea
30
H221
nut, lock, 1/2" steel
1 $1.99 ea
31
H220
fitting, strain relief, cord
1 $3.19 ea
32
E532
power cord, end, 25', 14/3
1 $44.99 ea
33
H254
washer, axle, cut 1/2" id
2 $0.99 ea
34
H224
axle, 17.50" x .50" dia, fb
1 $9.99 ea
35
H239
wheel, 8"
2 $28.99 ea
36
H219 cap, axle, 1/2"
2 $0.99 ea
37
P757
sol tank, firebird
1 $149.99 ea
38
H215
nut, hex, 1/4-20 s/s
2 $0.99 ea
39
H211
washer, 1/4"id x 1"od, flat, s/s
4 $0.99
40
G052
washer, buna 1-1/8" od x 3/16" id
4 $1.99 ea
41
H203
bolt, 1/4-20 x 1 1/4"
2 $0.99 ea
42
H912
bracket, rear, fb/spy
1 $9.99 ea
43
H307
washer, star, 1/4" steel zinc
4 $0.99 ea
44
H770
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
8 $0.99 ea
45
H378
bracket, front hinge, sp/fb
1 $8.99 ea
46
H201
bolt, 1/4-20 x 1/2", hex head, zinc
2 $0.99 ea
47
H204
bolt, 1/4-20 x 1 3/4" hex head, s/s
2 $0.99
48
B186
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
1 $8.99 ea
49
H299
washer, 11/16"id x 1-1/2"od x .075, s/s
5 $0.99 ea
50
B216
nipple, brass, 3/8" x close
1 $1.99 ea
PART NO.
DESCRIPTION
QTY.
MSRP
G010
filter, bag, vac tank, drawstring
1 $9.99 ea
G085
gasket strip, 3/4" x 36" x 1/8"
2 $4.99 ea
G147
strap, velcro, w/buckle
1 $3.49 ea
H434
plug, vent, heyco, 1/2"
2 $4.48 ea
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
51
B210
bushing, brass, 1/2"mpt x 3/8" fpt, hex
1 $2.49 ea
52
B119A
filter, strainer, 1/2"
1 $6.49 ea
53
B103
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
2 $4.49 ea
54
H212 washer, 9/16"id x 1"od, flat, s/s
4 $0.99 ea
55
B107 nipple, brass, 1/4"m, hex
2 $3.19 ea
56
B111
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
1 $3.49 ea
57
B102
qd, brass, 1/4" f
1 $17.99 ea
58
AH105
hose, 3/8" x 17-1/2", (OAL)
1 $31.99 ea
59
H244
adapter, pvc, 1-1/2" fms x fmpt
1 $4.99 ea
60
PH633-11
pipe, pvc, 1-1/2"
1
$4.99/Ft
61
H297
screw, 8 x 1/2", hex head, zinc
3 $0.99 ea
62
P755
elbow, U, 180, 1-1/2", float
1 $8.99 ea
63
H235
float, 1.5", ball style
1 $19.99 ea
64
G091
gasket, 7", vac lid
1 $11.99 ea
65
G090
lid, vac tank, black, 7"
1 $36.99 ea
66
H304
screw, #8 x 5/8 phil oval, s/s
6 $0.99 ea
67
H135
Cuff-Lynx, 2" m cuff x 2" mpt
1 $3.99 ea
68
G083
gasket, 2" inlet
1 $2.49 ea
69
A926
elbow, inlet assembly 2"
1 $15.99 ea
70
P758
vac tank, firebird
1 $186.99 ea
71
H225
valve, drain, 1-1/2"
1 $20.99 ea
72
H390A
bracket, "L" (all extracters)
2 $6.99 ea
73
H229
fitting, inlet, pvc, 1-1/2", gray
1 $5.99 ea
74
H326
plate, switch, 3 hole, fb
1 $6.99 ea
75
E515
switch, rocker, 2 position
2 $13.99 ea
PART NO.
DESCRIPTION
QTY.
MSRP
H141
cuff-lynx, 2" to 1.5" reducer
1 $3.99 ea
8350C
wand, 12" collapsable, w/disconnects
1 $159.99 ea
H226
spout, drain, 45 degree
1 $3.19 ea
A942
sol hose, 1/4" x 16', 3000psi
1 $71.99 ea
H295
vac hose, 1-1/2" 15' SW 1 $42.00 ea
B101
quick disconnect, male, 1/4" male x 1/4" fpt
1 $8.49 ea
B102
quick disconnect, 1/4" female x 1/4" fpt
1 $17.99 ea
G147
strap, velcro, w/buckle
5 $3.49 ea
AD127
stop sign register your product
1
n/a
ADM-CUFF-LYNX
cuff-lynx instruction guide
1
n/a
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
2000CS
SHEET 1 OF 2
2/28/12
OD
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
D. Cano
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
contractors special
Part prices are subject to change.Order parts at: www.mytee.com/products/product.php?id=2000CS

6
CONTRACTOR’S SPECIAL™ 2000CS PARTS & PRICING
1
5
3
7
8
10
12
13
14
15
9
16
17
11
18 20
19
22
23
24
25
26
27
28
31
30
32
33
34
35
36
53
54
55
58
53
56
57
48
49
50
49
51
52
46
6
3
37
38
39
40
40 39
41
42
44
6
59 60
62
63
64
65 66
70
71
72
44
73
3
3
47
3
45
75
to sol tank thru B186 (#48)
to sol tank thru B103 (#53)
to pump "IN" thru B160 (#12)
to pump "OUT" thru AH108S-25 (#18)
54
55
54
43
67
69
49
49
49
49
20
8
4
68
61
74
2
21
29
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
2000CS
SHEET 2 OF 2
SCALE: 1:5
REV
DWG. NO.
D
SIZE
TITLE:
NAME
DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
D Cano
2/28/12
OD
DO NOT SCALE DRAWING
contractors special

7
CONTRACTOR’S SPECIAL™ 2000CS WIRING DIAGRAM

8
CONTRACTOR’S SPECIAL™ 2001CS
2001CS FRONT 2001CS BACK
2001CS ACCESSORIES
1. Waist high controls
2. 2” Male Cuff-Lynx™
3. Female QD
4. Solution tank
5. Front vent
6. Solution lid
7. Push handle
8. Recovery tank lid
9. 3” casters
10. 8” wheels
11. Rear vent
12. 25’ Power cord
13. Bucket-high drain valve
14. Recovery tank
8300 EZ C - 1 2” Wand
4
2
5
9
H226 - Drain Elbow
8501- 15’ 1-1/2” Vac/Sol Hose
H141 - 1 1/2” Cuff-Lynx™
1
3
6
7
10
13
REPLACING HOSE CUFFS WITH CUFF-LYNX™
Once you receive your Contractor’s Special™, you will need to
replace the cuffs on your vacuum hose. To remove old cuffs, twist
clock-wise. To attach reducer Cuff-lynx™ to vacuum hose twist
counter clock-wise.
Twist clock-wise to remove standard cuffs.
Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.
8
11
12
14

9
CONTRACTOR’S SPECIAL™ 2001CS
2001CS ATTACH HOSES
Firmly attach hose and quick disconnect. Make sure quick discon-
nects snap together rmly. Once attached to unit connect Q.D. to
upholstery tool. Always inspect hoses for cracks or fraying.
2001CS VACUUM, PUMP & HEATER
To use vacuum, turn on vacuum. To use pump, turn on pump.
For heater, turn on heater.
VACUUM PUMP HEATER
2001CS FILL SOLUTION TANK
Lift lid to ll. For best results, ll with warm water (140o F).
ATTACH VAC & SOLUTION HOSE TO WAND
Attach hose cuff to end of wand tube. Attach female QD to male
QD located near the wand trigger.

10
CONTRACTOR’S SPECIAL™ 2001CS
2001CS SYSTEM MAINTAINER2001CS ADDING DEFOAMER
Weekly ushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Contractor’s Special™ vacuum motor .
2001CS RECOVERY DRAIN
When the oat shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.
2001CS LOCKING CASTERS
Locking casters help keep the machine remain stationary during
use.