Mytee HP100 Grand Prix Installation and operating manual

grand prix™
hp100
MYTEE PRODUCTS, INC | 13655 STOWE DRIVE | POWAY. CA 92064
PHONE: [phone] | FAX: [phone]
WWW.MYTEE.COM
WARRANTY
Mytee Products, Inc. endeavors to provide high quality products and product support to its customers and therefore backs up
all of its new products purchased from Mytee Products Inc. (“Mytee”) or any authorized Mytee distributor/service center
with this limited warranty. This limited warranty begins on the date of the customer’s purchase and is valid and avail-
able to the original purchaser only. Mytee’s products are for commercial use only and are not intended for personal,
family or household uses.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIP-
TION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT,
OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE PROPER
USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED
WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE
.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for 90 days from the date of original pur-
chase. “Wear parts” are items which wear out as a result of usage or the passage of time and are consumed despite
attempts to maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses, switches, ther-
mostats, plastisol parts, lters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts
deemed wear items in Mytee’s sole discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.
PUMP, VACUUM MOTOR AND HEATER 1-YEAR LIMITED WARRANTY: Mytee warrants that pumps, vacuum and oor
machine motors, and heaters will be free from manufacturing defects, defects in workmanship, and defects in material
for one (1) year from the date of original purchase. This warranty does not apply and is void if the pump, vacuum motor,
or heater has worn brush motors, water damage, chemical build-up, chemical damage, or evidence of abuse, neglect or
tampering. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs.
HOUSING 5-YEAR LIMITED WARRANTY: For ve (5) years from the date of purchase, Mytee warrants a percentage of the
cost of replacement of rotationally-molded housings pro-rated as follows: Mytee will pay 100% of replacement cost in
the rst year from the date of purchase, 75% of replacement cost in the second year from the date of purchase, 50% in
the third year, 25% in the fourth year, and 12% in the fth year. Replacement cost does not include the cost of shipping
or labor.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE
EXCLUSIVE REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO EVENT
SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY DAMAGES, OR PER-
SONAL INJURIES.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication,
improper installation, abuse, lack of maintenance, negligence in use or care, abnormal use, alteration of design, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone
other than Mytee or a Mytee authorized distributor or service center.
Mytee may make changes in products it manufactures and markets at any time; these changes are made without obliga-
tion to change, retrot, or upgrade any product previously sold or manufactured. Mytee has no obligation to honor the
limited warranties set forth herein unless the original purchaser, promptly upon discovering the warranty claim and
prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service center to describe
the claim and to receive and follow instructions for documenting and resolving the claim. In addition, the purchaser
must provide the product to which the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection.
If any provision or portion of this limited warranty policy is found to be unenforceable, then the remaining provisions
and portions shall remain valid and enforceable. If any provision or portion of this limited warranty policy is found to
be limited by law, then that provision or portion shall be construed to make it effective within the bounds of law. For ex-
ample, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have
the minimum duration required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made
herein shall be construed to apply to the fullest extent possible without violating the law.
The validity, construction and performance of this warranty policy shall be governed by the laws of the State of Califor-
nia, without respect to conicts of laws principles. The exclusive jurisdiction of any legal action arising from or related
to this warranty policy shall be in the State of California and no legal action shall be commenced elsewhere.
UNPACKING THE MACHINE
Before unpacking the machine, inspect all boxes and pallets for signs of shipping damage. Please be
aware that all packages leave Mytee Products in perfect condition. Any equipment or carton damage
caused during shipping is the responsibility of the freight company, and should be handled by ling a
claim with the carrier.
H375 - Hose Hanger
Grand Prix HP100
SAFETY LABELS
The safety labels
appear on the
machine in the
locations indicated.
Replace labels if they
become damaged or
cannot be read.
WARNING: Flammable materials can cause an
explosion or re. Do not use ammable materials in
tank(s). Flammable materials or reactive metals can
cause explosion or re.
WARNING LABEL- Located on back. Label warns
operator of safe practices of equipment.
MACHINE COMPONENTS
Vacuum
Tank Lid
Solution
Tank
Motor
Housing/
Base
Vacuum
Hose
Connector
Hose
Hanger
Solution
Hose
Connector
Blower Attachment
SETUP
1. Open lid of solution tank. Fill solution tank with
water or approved cleaning agent.
WARNING: Flammable materials can cause an
explosion or re. Do not use ammable solutions or
materials in tank(s).
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
ATTENTION: If using powdered cleaning chemicals,
mix prior to adding.
2. Attach solution hose. (Located front of machine.)
NOTE: Make sure the quick disconnects snap
together rmly. As you do this, always inspect
hoses for cracks or fraying. Do not use if hoses are
damaged.
3. Attach other end of solution hose to wand.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet.
FOR SAFETY: Do not operate machine unless cord is
properly grounded.
FOR SAFETY: Do not operate machine with the use
of an extension cord.
PRE-OPERATION
1. Vacuum carpet and upholstery and remove
other debris.
2. Perform MACHINE SETUP procedures.
3. Inspect power cord for damage.
OPERATION
7. Turning machine on.
A. Turn pump switch on.
B. Pull up on tool lever to release air in the line.
Hold lever until you have a steady ow of water
coming out of the wand.
C. Once pump is primed and you have pressure
in the solution line, turn on heater switch(s) (if
model is equipped with heater) and wait a few
minutes for water to heat up.
D. Once water is heated, turn on vacuum
motors and begin cleaning.
NOTE: When cleaning upholstery, always check
manufacturer’s cleaning instructions.
DRAINING RECOVERY TANK
FOR SAFETY: When servicing machine, unplug cord from
wall outlet.
1. Turn machine off and unplug power cord.
2. Remove solution & vacuum hose.
3.Attach 45º-drain elbow to dump valve and lift up drain
valve lever to empty recovery tank.
TIPS
1. Work away from outlet and power cord to prevent cord
damage.
2. Use a recommended foam control solution in the
recovery tank to prevent vacuum motor damage.
Periodically check for excessive foam buildup in solution
tank, and recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from
different direction.
4. When ball oat shuts off vacuum, it is time to empty the
dirty water from the recovery tank, and rell solution tank.
5. After cleaning, relieve water pressure from tool before
disconnecting hose. Squeeze trigger for ve seconds
after turning main power switch off.
MAINTENANCE
MACHINE MAINTENENCE
To keep machine in good working condition, simply follow
machine’s daily and weekly maintenance procedures.
Check valves and relief valves should be replaced
annually.
FOR SAFETY: When servicing machine, unplug cord from
wall outlet.
DAILY MAINTENANCE
1. Empty and rinse out solution tank thoroughly.
2. Wipe off power cord and check for damage, replace if
necessary. Coil cord neatly after use.
3. Clean machine with an all purpose cleaner and damp cloth.
WEEKLY MAINTENANCE
(EVERY 20 HOURS OF OPERATION)
1. Flush solution system with Mytee system
maintainer to dissolve normal chemical buildup.
a. Pour 7.5L (2 gal) of hot water 60°C
(140°F) into solution tank. Add Mytee
system maintainer according to mixing
instructions on bottle
FOR SAFETY: When using machine, follow
mixing and handling instructions on chemical
containers.
b. Operate machine for one minute.
c. Shut off machine and allow remaining
solution to break down chemical buildup
overnight.
d. Next day, spray out remaining
solution and ush system with 11L (3gal)
of clean water.
2. Inspect vacuum hoses for holes and loose
cuffs. Drain and dry the vacuum hose as well.
3. Inspect spray pattern for clogging. If
clogged, remove spray tips and soak them in
a recommended liquid neutralizer for up to six
hours. To remove spray tip, twist spray tip body
counter-clockwise.
4. Lubricate wheels with water resistant oil.
5. Inspect machine for water leaks and loose
hardware.
6. Remove oat shut-off screen from recovery
tank and clean.
NOTE: The oat shut off screen is not glued on.
Simply pull it off.
STORING MACHINE
1. Before storing machine, be certain to
completely drain and rinse tanks of all water and
solution.
2. Drain and dry the vacuum hose as well, using
the drain hose provided
3. Store machine in a dry area in the upright
position.
4. Open recovery tank cover to promote air
circulation
ATTENTION: Do not expose to rain. Store indoors.
ATTENTION: If storing machine in freezing
temperatures, be sure that machine and solution
system are completely drained and dry.
!
!
!
Instruction Manual
& Safety Guide
8501 - 15’ 1-1/4” Vac/Sol Hose H294 - 25’ Blower Hose
A919 - Exterior
Blower Attachment
PC88 -
Interior
Blower
Attachment
8400 - 3” Stainless
Steel Upholstery Tool
Vac/Sol Hose
3” Upholstery Tool
6
7
5
4
8
3
2
1
10
9
9
14
9
13
11
12
16
17
15
21
19
20
18
26
25
1
24
23
22
29
28
27
31
38
37
35
34
33
30
32 27
39
27
40
41
42
43
44
55 54
53
52
45
46
47
36
24
48
49
51
50
56
48
60
61
61
60
59
58
62
24
36 63
24 59 64
77
30
59
78
41
79
80
81
82
84
83
85
51
50
89
88
87 92
91
50
30
30
90
86
57
76
71 70
74
75
74
70
9
73
72
70
70
9
65
66
66
67
66
66
68
69
9
70
70
71
36
To female q.d.
thru B109 (#9)
To sol tank
thru B103 (#9)
To filter in sol tank
thru B186 (#65)
To inlet on base
(#50)
To pump "IN"
thru B160 (#21)
To relief valve
thru AH120 (#11)
To heater "OUT"
thru AH108S (#10)
Inside sol tank
D
C
B
A
A
B
C
D
1
2
3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
HP100
SHEET 2 OF 2
SCALE: 1:5
REV
DWG. NO.
D
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
PROPRIETARYAND CONFIDENTIAL
THEINFORMATION CONTAINED IN THIS
DRAWINGIS THE SOLE PROPERTY OF
MYTEEPRODUCTS, INC. ANY
REPRODUCTIONIN PART OR AS A WHOLE
WITHOUTTHE WRITTEN PERMISSION OF
MYTEEPRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
V.LaBarbera
11/1/07
DONOT SCALE
DRAWING
ITEMS NOT SHOWN:
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
ITEM NO. PART NO. DESCRIPTION QTY.
1 H273 nut, kep, #10-32 zinc 6
2 H230 screw, 10-32 x 1/2 phil pan 2
3 H528 bracket, heater mounting, dual 1
4 E571 heating rod, 600W, 115V 2
5 H274 screw, #6 x 3/16, phil pan head, self-tapping 10
6 E574 Thermostat, 310°F ± 10°F, Manual, 1/4" 2
7 E573 Thermostat, 200°, Auto, 1/4" 2
8 H903A heater, aluminum cast, single w/wrap & drilled holes 2
9 B103 elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 6
10 AH108S sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi 1
11 AH120 sol hose, 28" x 1/4", 1/4 fpt solid x 1/4 fpt swivel, neptune 1
12 B124 valve, brass, relief, 175 psi 1
13 B113 tee, brass, 1/4" fpt 1
14 AH156 hose, 3/8" x 6", (OAL), f x fsw, surge, 1600psi 1
15 AH103 hose, 3/8" x 10", (OAL), f x fsw, surge, 1600psi 1
16 B207 elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt 1
17 B108 valve, brass, 1/4" check 1
18 B172 elbow, brass, 90 deg, 1/2" barb x 3/8"mpt 1
19 PH615 sol hose, 1/2" kuri 100psi 1
20 H347 clamp, hose, 5/16-29/32 2
21 B160 adapter, brass, 1/2" barb x 3/8" fsw, ball end 1
22 C305 pump, 100psi, demand, 115V 1
23 H222 screw, #10-32 x 1-1/4" phil pan head, zinc 4
24 H210 washer, 1/4" flat, s/s 16
25 B136 elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt 1
26 B105 bushing, brass, 3/8"mpt x 1/4" 1
27 H217 clamp, hose, 2-1/4 DIA 3
28 PH627 vac hose, 1-1/2", wire reinforced 1
29 H300 cuff, black 1.5" 1
30 H770 bolt, 1/4-20 x 1/2" serrated hex flange, zinc 9
31 C302 vac motor, 3 stage, 115V, tangential 1
32 G004 gasket, vacuum motor 1
33 H501 vac support, 3 stage, 4-1/16" 3
34 H201 bolt, 1/4-20 x 1/2" hex head, zinc 3
35 H768 bolt, 1/4-20 x 3/4" serrated hex flange, zinc 3
36 H216 nut, lock, 1/4-20, nylon insert 13
37 P735 manifold, single vac 1
38 H330 plate, single manifold, 6.5" x 9" 1
39 PH628 vac hose, 2", wire reinforced 1
40 PH633-03 pipe, pvc, 1-1/2" 1
41 H244 adapter, pvc, 1-1/2" fms x fmpt 2
42 E531 power cord, end, 25', 12/3 yel 1
43 H220 fitting, strain relief, cord 1
44 H221 nut, lock, 1/2" steel 1
45 P756 base, firebird 1
46 H343 screw, #10 x 5/8" hex head, zinc 8
47 H296 guard, cooling fan, wire 2
48 H203 bolt, 1/4-20 x 1-1/4" hex head 10
49 H667 caster, 3" 2
50 H229 fitting, inlet, pvc, 1-1/2", gray 3
ITEM NO. PART NO. DESCRIPTION QTY.
51 G001 gasket, inlet, 1.80" i.d. 2
52 H219 cap, axle, 1/2" 2
53 H239 wheel, 8" 2
54 H224 axle, 1/2" x 17-3/4", fb 1
55 H254 washer, axle, cut 1/2" id 4
56 G061 cover, sol tank, fb 1
57 P757 sol tank, firebird 1
58 H215 nut, hex, 1/4-20 s/s 2
59 H213 washer, 1/4" lock, s/s 6
60 H211 washer, 1/4"id x 1"od, flat, s/s 4
61 G052 washer, buna 1-1/8" od x 3/16" id 4
62 H204 bolt, 1/4-20 x 1-3/4" hex head, s/s 2
63 H378 bracket, front hinge, sp/fb 1
64 H201 bolt, 1/4-20 x 1/2" hex head, zinc 2
65 B186 elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt 1
66 H299 washer, 11/16"id x 1-1/2"od x .075, s/s 4
67 B216 nipple, brass, 3/8" x close 1
68 B210 bushing, brass, 1/2"mpt x 3/8" fpt, hex 1
69 B119A filter, strainer, 1/2" 1
70 H212 washer, 9/16"id x 1"od, flat, s/s 6
71 B111 adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex 2
72 B107 nipple, brass, 1/4"m, hex 1
73 AH105 hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi 1
74 H413 washer, nylon, 9/16id x 1-1/16od x .031 2
75 B106 nipple, brass, 1/4" x close 1
76 B102 qd, brass, 1/4" f 1
77 H912 bracket, rear, fb/spy 1
78 H922 knob, thumb screw, for bracket 2
79 PH633-11 pipe, pvc, 1-1/2" 1
80 P755 elbow, U, 180, 1-1/2", float 1
81 H235 cage, float, standard 1
82 H304 screw, #8 x 5/8 phil oval, s/s 6
83 G090 lid, vac tank, black, 7" 1
84 G091 gasket, 7", vac lid 1
85 A925 elbow, inlet assy 1-1/2" 1
86 P758 vac tank, firebird 1
87 H326 plate, switch, 3 hole, fb 1
88 E515 switch, rocker, 2 position 3
89 H246 screw, #8-32 x 3/8" SHCS, alloy 4
90 H390A bracket, "L" (all extracters) 2
91 H225 valve, drain, 1-1/2" 1
92 H226 spout, drain, 45 degree 1
D
C
B
A
A
B
C
D
1
2
3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
HP100
SHEET 1 OF 2
SCALE: 1:3
REV
DWG. NO.
D
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
PROPRIETARYAND CONFIDENTIAL
THEINFORMATION CONTAINED IN THIS
DRAWINGIS THE SOLE PROPERTY OF
MYTEEPRODUCTS, INC. ANY
REPRODUCTIONIN PART OR AS A WHOLE
WITHOUTTHE WRITTEN PERMISSION OF
MYTEEPRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
V.LaBarbera
11/1/07
DONOT SCALE
DRAWING
H226 -
45ODrain Elbow

OPTIONAL ACCESSORIES
The following accessories and tools are available for this unit, and can
be purchased separately at your local Mytee dealer. You can nd more
information on any of them at www.mytee.com
Stainless Steel
Crevice Tool
(8700)
Airmover
(2200)
TROUBLESHOOTING
SYMPTOM: UNIT WILL NOT TURN ON:
PROBLEM: Not plugged in.
SOLUTION: Plug machine in proper outlet.
PROBLEM: Circuit breaker has popped.
SOLUTION: Reset circuit breaker. Make sure no other items are
running on the same circuit as machine. Outlet must
be a 20-amp circuit.
SYMPTOM: PUMP IS NOT RUNNING PROPERLY:
PROBLEM: Quick disconnects are not completely locked together.
SOLUTION: Snap quick disconnects rmly together.
PROBLEM: The solution tank is empty.
SOLUTION:
Fill the solution tank up with a premixed liquid detergent.
PROBLEM: Jet on upholstery tool is clogged.
SOLUTION: Clean jet with soft wire brush or remove jet and ush clean.
PROBLEM: Filters are clogged.
SOLUTION: Remove lters and rinse clean with water.
PROBLEM: Heater is blocked with hard water deposits.
SOLUTION: Flush out heaters with Mytee Products, Inc. system
maintainer solution.
PROBLEM: Brass check valve is stuck.
SOLUTION: Replace with new check valve.
PROBLEM: Pump wire has become disconnected.
SOLUTION: Reconnect wire.
PROBLEM: Switch on switch plate is bad.
SOLUTION: Replace switch.
PROBLEM: Pump motor brushes are worn out.
SOLUTION: Replace pump.
SYMPTOM: HEATER IS NOT WORKING PROPERLY:
PROBLEM:
The back up sensor, mounted on the heater has popped .
SOLUTION: Reset sensor by pushing in button.
PROBLEM: Heating element is bad.
SOLUTION: Replace element.
SYMPTOM: VACUUM MOTOR IS NOT WORKING PROPERLY:
PROBLEM:
Hose not connected tightly to upholstery tool or machine.
SOLUTION: Connect hose tightly.
PROBLEM: Drain valve is not shut completely.
SOLUTION: Close drain valve completely.
PROBLEM: Vacuum tank lid is not on tightly.
SOLUTION: Secure the vacuum tank tightly.
PROBLEM: Ball oat is shut off.
SOLUTION: Empty the vacuum tank of all wastewater.
PROBLEM: Water is coming out of vacuum motor.
SOLUTION: Use a low foaming detergent.
PROBLEM: Upholstery tool or wand is clogged with hair, carpet
bers and or debris.
SOLUTION: Clean upholstery tool or oor wand jets.
PROBLEM: Ball oat is not installed correctly.
SOLUTION: Make sure that ball oat is rmly installed on the elbow.
This machine is intended for commercial use. It is
designed to clean carpet and upholstery in an indoor
environment and is not constructed for any other
use. Use only recommended cleaning solutions and
accessory tools.
All operators must read, understand and practice
the following safety precautions.
The following safety alerts symbols are used
throughout this manual as indicated in their description:
WARNING: To warn of hazards or unsafe practices
which could result in severe personal injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
The following information signal potentially dangerous
conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
• Unless trained and authorized.
• Unless operator manual has been read and
understood.
• In ammable or explosive areas.
• Unless cord is properly grounded.
• With damaged cord or plug.
• If not in proper operating condition.
• In outdoor areas.
• In standing water.
2. Before operating machine:
• Make sure all safety devices are in place and
operate properly.
3. When using machine:
• Do not run machine over cord.
• Do not pull machine by plug or cord.
• Do not pull cord around sharp edges or
corners
• Do not unplug by pulling on cord.
• Do not stretch cord.
• Do not handle plug with wet hands.
• Keep cord away from heated surfaces.
• Report machine damage or faulty operation
immediately to your distributor.
• Follow mixing and handling instructions on
chemical containers.
4. Before leaving or servicing machine:
• Turn off machine.
• Unplug cord from wall outlet.
5. When servicing machine:
• Unplug cord from wall outlet.
• Avoid moving parts.
• Do not wear loose jackets, shirts, or sleeves.
• Use manufacturer supplied or approved
replacement parts.
SAFETY PRECAUTIONS Machine must be grounded.
If it should malfunction
or breakdown, grounding
provides a path of least
resistance for electrical
shock. This machine is
equipped with a cord having
an equipment-grounding
conductor and grounding
plug. The plug must be
plugged into an appropriate
outlet that is properly
installed in accordance
with all local code and
ordinances. Do not remove
ground pin; if missing,
replace plug before use.
WARNING:
Hazardous Voltage. Shock
or electrocution can result.
Always unplug machine
before servicing.
WARNING:
Flammable materials can
cause an explosion or
re. Do not use ammable
materials in tank(s).
WARNING:
Flammable materials or
reactive metals can cause
an explosion or re.
!
!
!
!
45º Elbow
HEATER
VACUUM
STEP 1
STEP 10
STEP 9
STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8
STEP 17
STEP 20
STEP 19
STEP 18
STEP 11 STEP 12 STEP 13 STEP 14 STEP 15 STEP 16
WHEN WORK
IS COMPLETE,
UNPLUG CORDS
AND HOSES.
WRAP AND CLEAN
HOSES. CLEAN
ALL TANKS.
WHEN FLOAT
SHUTS OFF
VACUUM, EMPTY
TANKS.
TO CLEAN HEAVILY
SOILED AREAS,
REPEAT CLEANING
FROM DIFFERENT
DIRECTION.
WAIT 8 - 10
MINUTES FOR
UNIT TO PRE-HEAT.
RE-KEY
UPHOLSTERY TOOL
UNTIL HOT WATER
BEGINS FLOWING.
ONCE HOT WATER IS
FLOWING, RELEASE
TRIGGER AND PRE-
HEAT AN ADDITIONAL
4-5 MINUTES.
TURN ON THE
VACUUM MOTOR.
WORK AWAY
FROM CORDS
TO AVOID
DAMAGE.
FOR FLOOR
CLEANING,
UNPLUG
TOOL AND
ATTACH
FLOOR
WAND.
BEGIN CLEANING.
MAKE TWO DRY
PASSES TO EVERY
WET PASS.
USE A
DEFOAMER
IN YOUR
RECOVERY
TANK.
TURN ON PUMP.
KEY TOOL UNTIL
YOU HAVE A
STEADY FLOW.
RELEASE TOOL
TRIGGER. TURN
ON HEATER.
PLUG UNIT
INTO A 20 AMP
GROUNDED
OUTLET.
ATTACH HOSES
TO UPHOLSTERY
TOOL.
ATTACH HOSES.FILL
SOLUTION
TANK.
FAQ’S FOR HP100 GRAND PRIX
Q: How much does the HP100 weigh and
what are the shipping dimensions?
A: 90 Pounds - Box dimensions are
30”x20”x48”. Must ship motor freight.
Q: What comes standard with the HP100?
A: The HP100 comes with two hose hangers
(H375), a 25’ 12/3 Yellow Safety Cord, 15’ 1-1/4”
Vacuum/Solution Hose (8501), 25’ Blower Hose
(H234), Exterior Blower Attachment (A919),
Interior Blower Attachment (PC88), and
a 3” Stainless Steel Upholstery Tool (8400).
Please see owner’s manual for breakdown.
Q: Does Mytee recommend a tool for the
machine?
A: A variety of tools can be used with the unit,
including our 8390 wand, 8700 crevice tool, and
8400 upholstery tool.
Q: Where do I plug the machine in?
A: The HP100 requires a 20A grounded circuit.
Please note: GFI outlets may trip before the
breaker setting.
Q: What is the proper pre heat cycle for the HP100?
A Turn pump switch to the on position and prime
pump through the solution hose and the tool.
Then turn the heater switch to the on position.
Let the machine sit idle for 8-10 minutes. Spray
tool until you feel the hot water from the jet. Let
machine sit idle for 3-5 minutes. This will insure
the water in the heater and hoses will be at the
hottest point to start cleaning.
Q: Are the pumps re-buildable for the HP100?
A: Yes, both the seals and the pistons have repair
kits available. Please see the pump manual that
shipped with your machine for the maintenance
schedule.
Q: Is there anything I can do to increase the
expected life of my machine?
A: Running the vacuum motors with the tank empty
and lid off will allow excess moisture in the
vacs to dry off. You should also run a System
Maintainer through the system to keep the hoses,
pump, and heater clean and free of debris.
System Maintainer
(3601)
10” Single
Jet, Two Piece
Floor Wand.
(8390)
Auto Vac
Allows dry Vacuuming
with your Extractor
(AV1)
Tradewind™ Airmover
(3000)
Mytee-Dry™
(2700)
FOR BEST
RESULTS, FILL
WITH WARM
WATER (140OF)
FOR DRY
VACUUMING,
ATTACH AUTO
VAC (AVI).