N-Com M5 Instruction Manual

EN M5
M5 - 29/02/2016 09:25:00
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product.
N-Com M5 was made using the most advanced technologies and the best
materials. Long-running tests and thorough system development have allowed
the highest audio quality to be achieved.
For additional information about M5 visit the website www.n-com.it
Firmware Version: 1.0x
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table below:
M5
The Bluetooth system complies with the main safety requirements and
other applicable provisions of Directive 99/5/CE, Directive 2009/65/EC,
Directive 2011/65/CE, Directive 2012/19/EU
Battery
charger
Directive 2006/95, 2004/108, 2009/65/EC, 2011/65/CE, 2012/19/EU,
2009/125/CE
Battery Directive 2006/66
The Declarations of Compliance can be downloaded from the website www.n-com.it
(Download section).
Model: M5 FccID: Y6MNCOM9 R-NZ
Model: WRC FccID: Y6MNCOM11 R-NZ
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.

Contents
1. WARNINGS AND SAFETY.................................................................................................4
1.1.Road safety ................................................................................................................................................................4
1.2.Switching on the system in safe environments ......................................................................................... 4
1.3.Interferences..............................................................................................................................................................4
1.4.Appropriate use ....................................................................................................................................................... 4
1.5.Qualified personnel................................................................................................................................................ 5
1.6.Accessories and batteries.................................................................................................................................... 5
1.7. Disposal ..................................................................................................................................................................... 5
2. CONTENT OF THE PACKAGING ......................................................................................6
3. INSTALLATION....................................................................................................................7
3.1.Positioning the speakers and the microphone.......................................................................................... 7
3.2.Installing the e-box ................................................................................................................................................ 8
3.3.Positioning the Bluetooth keypad.................................................................................................................11
3.4.Operating of the Bluetooth keyboard .........................................................................................................11
4. FUNCTION KEYS...............................................................................................................11
5. BASIC FUNCTIONS...........................................................................................................12
5.1.Auto On / Off Function.......................................................................................................................................12
5.2.N-Com Wizard and N-Com App....................................................................................................................12
5.3.Pairing up with Bluetooth devices.................................................................................................................12
6. MOBILE PHONE................................................................................................................13
6.1.Friend Number .......................................................................................................................................................13
6.2.Managing two mobile phones (or Bluetooth devices).........................................................................14
7. MUSIC VIA BLUETOOTH – A2DP BLUETOOTH PROTOCOL ....................................14
8. MUSIC VIA CABLE ............................................................................................................14
9. SATELLITE NAVIGATOR FOR MOTORCYCLES ............................................................15
9.1.Navigators on Smartphone (Smart Navi System)...................................................................................15
10. FM RADIO..........................................................................................................................15
11. EMERGENCY STOP SIGNAL (ESS)..................................................................................16
12. RIDER-PASSENGER INTERCOM.....................................................................................16
12.1.Rider-Passenger intercom pairing up .......................................................................................................16
12.2.Rider-Passenger intercom function............................................................................................................16
13. BIKE-TO-BIKE INTERCOM...............................................................................................17
13.1.Bike-to-Bike Intercom Affiliation (Standard configuration) ............................................................17
13.2.Bike-to-Bike intercom function ....................................................................................................................18
14. SETTING MODE ................................................................................................................19
15. BATTERY AND RECHARGE..............................................................................................19
15.1.Low battery signal ..............................................................................................................................................19
15.2.Charging the system .........................................................................................................................................19
16. SUMMARY TABLE OF CONTROLS – STANDARD CONFIGURATION .....................20
17. LIMITED WARRANTY.......................................................................................................22
17.1.Warranty coverage.............................................................................................................................................22
17.2.Exclusions and limitations of the coverage ............................................................................................22
17.3.Validity of this limited warranty ...................................................................................................................22
17.4.Procedure for the forwarding of claims ...................................................................................................23
17.5.Product identification .......................................................................................................................................23
18. WARRANTY REGISTRATION FORM..............................................................................24

EN
4
1. WARNINGS AND SAFETY
Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead
to dangerous situations.
Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and
the like.
Caution: Installation of the N-Com M5 system results in a weight increase of approximately 100 g, which is added to
the weight of the helmet and of the other accessories.
Warning: The electronic components of the N-Com system mounted inside the helmet are not waterproof.
Consequently, make sure the inside of the helmet, including the comfort padding, does not get wet in order to
avoid damage to the system. If it does, remove the N-Com system and the helmet comfort padding and let it
air dry. Disconnect the battery connector and let it dry as well.
1.1. Road safety
Always obey all Traffic Regulations in force. While riding the motorcycle, your hands should always be engaged in
actually riding the vehicle. Any operation to the N-Com system must be carried out with the vehicle stopped.
Specifically:
Set your cell phone on automatic answer (see the cell phone instructions to do this).
If your cell phone is not equipped with this function, first stop your vehicle in a safe area, in compliance with
Traffic Regulations and then answer the call.
Do not make any calls while riding. Stop your vehicle in a safe place in compliance with Traffic Regulations,
and then make the call.
Adjust the volume so that it does not cause a disturbance or distraction while riding and at the same time
allows you to distinctively hear background noises.
Do not operate your cell phone or other devices connected to N-Com while riding your motorcycle.
In all cases, obey the Traffic Regulations and remember that riding the motorcycle has absolute priority over
any other maneuver.
The M5 system is equipped with an emergency brake light (ESS – Emergency Stop Signal). The ESS system IS
NOT intended to replace the stop or brake lights fitted on the motorcycle, consequently its operation alone is
not enough for proper brake signaling.
Make sure that the use of the emergency brake light (ESS – Emergency Stop Signal) is not in conflict with the
regulations in force in the country where you will be travelling.
1.2. Switching on the system in safe environments
When using the N-Com system, comply with all limitations and instructions related to the use of cell phones.
Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when the devices
can cause interference or dangerous situations.
Turn off while refueling. Do not use the N-Com system in filling stations. Do not use the device near
combustible materials or chemical products.
Turn off in proximity to explosive materials.
1.3. Interferences
All phones and devices with wireless signal transmission are subject to interferences that may affect the
performance of the device connected to them. These interferences are not ascribable to a defect of the N-Com
system.
1.4. Appropriate use
Use the device only in the normal position, as described in the product documentation. Do not attempt to
disassemble, tamper with or modify any part of the N-Com system.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before
you use the system on the road.
Caution: Adjusting the volume to very high levels may cause damage to your hearing.

M5
5
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to
avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your
hearing.
Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of
the helmet itself, thus creating dangerous conditions. Install the N-Com system according to the instructions
provided in the product documentation. In case of doubt, please contact your local N-Com dealer.
Warning: Listening to other equipment should not interfere with driving the vehicle, which must be the top priority
at all times. Carry out all operations on the electronic equipment and on the N-Com system with the vehicle
stopped, in compliance with Traffic Regulations.
Caution: The N-Com system allows reception of the FM radio signal. Any radio license fees are to the user’s charge.
1.5. Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always
turn to your local dealer.
The helmet is a safety device. Tampering with it and/or with the electronic system inside the helmet, in
addition to invalidating the product warranty, can also lead to dangerous situations.
1.6. Accessories and batteries
Only use the type of batteries, battery chargers and accessories approved by Nolan for the specific model.
The use of a battery type different from the recommended one may lead to dangerous situations and
invalidate the warranty.
Contact your local dealer to see about the availability of approved accessories.
When disconnecting the power supply cable of any accessory or of the battery charger, always grab and pull
the plug not the cable.
Do not use batteries for purposes other than the prescribed ones.
Never use batteries or battery chargers that turn out to be damaged.
Do not short-circuit the battery.
Keep the battery at a temperature between 0° / +32°C (charging); -20° / +55°C (in use).
Danger of fire or explosion: do not throw the batteries into a fire nor expose them to high temperatures!
Do not throw out batteries together with household refuse. The batteries should be disposed of in
compliance with local regulations.
Do not wear the helmet while the battery is recharging.
The helmet should never be left within the reach of unsupervised children in order to prevent damage to
their health caused by access to the batteries.
Wireless keypad battery CR2016
M5 system battery Li-Po 523450P Litio 3,7V – 1000 mAh
Battery charger S-TR-009L 100/240V – 50/60 Hz 5V - 0.5 A
1.7. Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the
system from the helmet. Once the system has been disassembled, dispose of it according to the following
instructions:
The presence of a crossed-out wheelie bin indicates that in the European Union the product is
subject to separate collection at the end of its useful life.
Do not dispose of these products together with undifferentiated urban waste.
The proper disposal of obsolete equipment contributes to preventing possible negative consequences on
people’s health and on the environment.
For more detailed information on the disposal of obsolete equipment, contact your municipality, a waste
disposal service or the store where the product was purchased.

EN
6
2. CONTENT OF THE PACKAGING
The N-Com M5 package contains:
e-box M5 Bluetooth wireless keypad Wiring system
Microphone for
full-face helmets Flexible boom microphone Velcro kit
Fixing feet kit USB battery charger PC connection cable
E-box safety block Microphone windscreen

M5
7
3. INSTALLATION
3.1. Positioning the speakers and the microphone
Fig. 1

Remove the protective film from the Velcro of
the speakers;

Position the speakers near your ears, so that they
stick perfectly to the helmet.
N.B.: If possible, position the speakers
underneath the comfort padding of the helmet.
Install the microphone
Fig. 2
Flexible boom microphone – recommended

Position the swivel part of the microphone with
the Velcro/adhesive part between helmet shell
and the padding, so that the microphone is
properly positioned in front of your mouth.
Caution: make sure that the side of the
microphone support with the writing “N-Com”
is facing inward.
Fig. 3
Wire microphone

In case it is not possible to use the swivel
microphone, install a wire microphone.

Use the Velcro/adhesive to secure the
microphone inside the helmet, so that it is in
front of your mouth.
N.B.: This type of microphone is more
recommended for full-face helmets.

EN
8
Fig. 4 Fig. 5
Connect the microphone with the counterpart on the wiring (Fig. 4).
Pass the wiring e-box connector through, out of the back of the helmet, so that it can be hooked up
to the e-box afterwards (Fig. 5).
3.2. Installing the e-box
Fig. 6
The M5 e-box must be positioned in the back of
the helmet, using the adhesive feet supplied as
standard equipment.

Thoroughly clean the surface of the helmet
where the feet will be applied;

Insert the fixing feet in the device;

Make sure the e-box is properly positioned on
the helmet shell.
If necessary, depending on the different types of helmets, replace one or more thin feet with thicker
ones, until you find the combination that allows the e-box to properly stick to the helmet (Fig. 7-10).
Fig. 7 Fig. 8 Fig. 9 Fig. 10

M5
9
Important: Should you wish to use the emergency brake light (see Chapter 10), you need to position
the M5 e-box so that it is vertical or with an inclination of +/-30° with respect to the vertical axis
while you are riding, so as to allow the triaxial accelerometer to properly measure the motorcycle
deceleration. Based on the type of helmet used and the riding style, choose the combination of
feet (thick-thin) that allows proper positioning.
Important: When positioning the e-box on the helmet, the wiring connector must not stick out from
the edge of the helmet or be twisted (fig. 11 and 12).
Fig. 11 Fig. 12
Fig. 13

Insert the wiring connector all the way inside the
e-box, making sure that it is pointing in the right
direction: the letter “n” must be visible (as
shown in the figure).

EN
10
Position the "safety block" on the wiring, then secure it in the e-box housing (Fig. 14-15-16).
Fig. 14 Fig. 15 Fig. 16
Remove the protective film from the feet and apply the system to the helmet (Fig. 17-18);
Important: If the position is less than perfect, remove the foot from the helmet immediately and try
again.
Fig. 17 Fig. 18
NB: It will take up to 24 hours for the adhesive to stick completely. During this time, do not expose
the helmet to atmospheric agents. During the first 12 hours, do not remove the e-box from the
feet.
Caution: Once the adhesive is applied, it cannot be reused in a different position and will have to be
replaced once removed.

M5
11
3.3. Positioning the Bluetooth keypad
Fig. 19
The Bluetooth wireless keypad can be
positioned as desired, provided it is within a 5-
meter radius from the e-box.
The recommended position is the left side of the
helmet, so that it can be easily used with the left
hand.
Thoroughly clean the surface of the helmet where the keypad will be applied;
Find the best spot where to position the keypad, making sure that the surface of the base sticks
perfectly to the shell.
Remove the protective film and apply the keypad to the helmet;
Important: If the position is less than perfect, remove the foot from the helmet immediately and
try again.
NB: It will take up to 24 hours for the adhesive to stick completely. During this time, do not expose
the helmet to atmospheric agents.
Caution: Once the adhesive is applied, it cannot be reused in a different position and will have to be
replaced once removed.
3.4. Operating of the Bluetooth keyboard
The Bluetooth keyboard comes already paired up with the system, so it is immediately operational.
In case you replace the original keypad with a new one, the new keypad will have to be paired up:
put the system in Setting Mode
press the “n” key and the “ on ” key at the same time
A voice message inside the helmet confirms that the pairing up was successful.
4. FUNCTION KEYS
“BACK”BUTTON
“
▲
”
BUTTON
“
▼
”
BUTTON
“
N
”
BUTTON
“
on
”
BUTTON

EN
12
5. BASIC FUNCTIONS
System ON Briefly press “BACK”, until the LEDs turn on and you hear a beep in the
headset.
System OFF Press “BACK” and keep it pressed for about 2 seconds, until the LEDs
turn off and you hear a beep in the headset.
Increase Volume Briefly press “” to increase the volume. A double tone signals the
highest volume level.
Decrease Volume Briefly press “” to decrease the volume. A double tone signals the
lowest volume level.
5.1. Auto On / Off Function
The system does not have to be turned on and off every time you use the motorcycle: thanks to the
triaxial accelerometer, if the helmet does no move for more than 30 seconds, the M5 system goes
into “deep sleep” mode. The system is completely turned on as soon as movement is detected.
If the system is in “deep sleep” mode for more than 7 days, it turns off completely. To turn it back on,
the “on” key need to be pressed.
5.2. N-Com Wizard and N-Com App
“N-Com Wizard” is the PC application that can be used to manage and configure the M5
system.
The program can be downloaded from the Internet site www.n-com.it, in the “Download”
section. In order to use it, a helmet equipped with M5 must be connected to the PC,
using the USB cable supplied with the system.
The functions that can also be managed from the N-Com Wizard are listed here below
with the specific icon.
The N-Com system is preset to be hooked up to the “N-Com App”, the application
compatible with Android, iPhone and iPad that can be used to configure and operate the
N-Com system directly from a Smartphone.
With the N-Com App, you can carry out most of the functions included in the N-Com
Wizard program or, alternatively, it can be used as a wireless Bluetooth keypad.
The N-Com APP can be downloaded free of charge from Google Play or Apple Store.
For additional details, please visit the website www.n-com.it
The functions that can also be managed from the N-Com Wizard are listed here below
with the specific icon.
5.3. Pairing up with Bluetooth devices
Make sure the M5 is turned off;
Put the system in setting mode: press the “BACK” key and keep it pressed for 4 seconds,
until the red LED starts to flash quickly;
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device;
Select the N-Com device. If a password is requested, enter 0000 (four zeros);
Connection between the two devices is established after a few seconds.
Note: The affiliation is stored in the helmet and in the cell phone and it is not lost when the two
devices are turned off. As a result it needs to be carried out only once.

M5
13
Automatic Connection Once the Bluetooth device has been paired up, connection is automatic
when the system is turned on.
Manual Connection
In case connection is not automatically initiated after a few seconds, you
can connect from the Bluetooth device or by pressing “ on ” and keep it
pressed for about 2 seconds.
6. MOBILE PHONE
Answering a phone call Briefly press any key when you hear the incoming call signal.
Voice call Press “ on ” and keep it pressed for about 2 seconds.
Redial last number Press “ on ” and “n” at the same time.
Dial Friend Number Press “n” and keep it pressed for about 2 seconds.
Hanging up/rejecting a
phone call Press “
on ” and keep it pressed for about 2 seconds.
Transferring a call from
helmet to mobile phone
To transfer an ongoing call from the helmet to the mobile phone, press
both “ on ” and “n” at the same time and keep them pressed for 2
seconds.
Manual phone
connection Press “
on ” and keep it pressed for about 2 seconds.
Manual phone
disconnection Press “” and keep it pressed for about 4 seconds.
Conference call function
When a call comes in on a mobile phone connected via Bluetooth to M5, the Rider-Pillion Passenger
intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet,
simply turn on the intercom manually during the phone call.
Turning on the phone conference call
function During the phone call, briefly press “n”.
Turning off the phone conference call
function During the phone call, briefly press “n”.
N.B.: The Phone Conference Call function can only be used with a Rider-Pillion Passenger intercom
(channel 1) and not with Bike-to-Bike communication (channels 2-6).
6.1. Friend Number
When you use the N-Com Wizard or the N-Com App, you can choose a “Friend
Number”, which you can be call by pressing a speed-dial button.
Calling the Friend
Number Press the “n” key and keep it pressed for 2 second.

EN
14
6.2. Managing two mobile phones (or Bluetooth devices)
The M5 system can be hooked up to two phones (or Bluetooth) devices at the same time.
The second phone (secondary device) can receive calls but not make them.
To pair up the second Bluetooth phone (secondary device):
Make sure the M5 is turned off;
press the “BACK” key and keep it pressed for 4 seconds, until the red LED starts to flash
quickly (setting mode);
Press the “ on ” key and keep it pressed for about 2 seconds.
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device;
Select the N-Com system from the list
7. MUSIC VIA BLUETOOTH – A2DP BLUETOOTH PROTOCOL
Play music (Play) Briefly press “ on ”.
Pause function (Pause) When the player is connected and playing music, briefly press
“ on ”.
Next track (Skip) When the player is playing music, press “” for 2 about seconds.
Previous track (Rew) When the player is playing music, press “” for 2 about seconds.
Turning off the A2DP Press “ on ” and keep it pressed for about 4 seconds.
Turning on the A2DP The A2DP is already active when the system is turned on;
otherwise, press the “ on ” key briefly.
You can also configure these settings through Smartphone Android, iPhone and iPad
thanks to the dedicated N-Com App.
8. MUSIC VIA CABLE
Connect the mini USB connector of the Multimedia Wire (not included) to the helmet and the other
end to the audio device. A colored band on the cable indicates the connector to be hooked up to the
audio device.
Turning on the cable audio Press the “ on ” key three times.
Turning off the cable audio Press the “ on ” key three times.

M5
15
9. SATELLITE NAVIGATOR FOR MOTORCYCLES
M5 system is compatible with the most common satellite navigators for motorcycles. For a list of
compatible models and additional details, visit the website www.n-com.it
To pair up a satellite navigator to the M5 system, follow the same procedure illustrated in Chapter 5.3.
GPS Conference Call Function
The Conference function allows you to keep the “Rider-Pillion Passenger” intercom open even while
the satellite navigator is giving instructions, thus preventing the intercom mode to be turned off every
time the navigator gives instructions. However, if you wish to activate the Conference GPS function,
simply turn on the intercom manually during the GPS directions.
Turning on the GPS Conference
function During the GPS directions, briefly press “n”.
Turning off the GPS Conference
function During the GPS directions, briefly press “n”.
At the end of the GPS communication, the intercom with the second helmet stays open and the
"Conference" setting is stored for future GPS communications.
N.B.: The GPS Conference function can only be used with the Rider-Pillion Passenger intercom
(channel 1) and not with the Bike-to-Bike communication (channels 2-6).
9.1. Navigators on Smartphone (Smart Navi System)
By connecting the M5 system to a Smartphone, all navigator instructions are sent to the helmet
through the A2DP profile. During each navigator communication, the intercom via Bluetooth is
automatically cut off and subsequently restored when the navigator has stopped giving road
instructions (SMART NAVI SYSTEM function).
The Smart Navi System function can be turned off in Setting Mode (see Chapter 14).
10. FM RADIO
Turning on the radio Press the “ on ” key twice
Turning off the radio Press the “ on ” key twice.
New station automatic search Press “” and keep it pressed for 2 seconds.
Pre-setting a radio station (max.
6 stations) Press “” and keep it pressed for 4 seconds.
Changing radio stations (among
the pre-set ones) Press “” and keep it pressed for 2 seconds.
This function can also be turned on through PC using the “N-Com Wizard”
program or through Smartphone Android, iPhone and iPad thanks to the
dedicated N-Com App.

EN
16
11. EMERGENCY STOP SIGNAL (ESS)
The M5 system is equipped with a LED system to assist emergency braking. In case of sudden
braking, the LEDs on the M5 flash for a few seconds.
The braking level can be adjusted through a PC (N-Com Wizard) or Smartphone
Android, iPhone and iPad thanks to the dedicated N-Com App.
Turning on/off the Emergency Stop
Signal (ESS)
Press the BACK key briefly
OR
Press the “” and “” keys and keep them pressed for about
2 seconds.
N.B.: We recommend turning off the Emergency Stop Signal on the Rider’s helmet in case a Pillion
Passenger is riding on the back.
12. RIDER-PASSENGER INTERCOM
12.1. Rider-Passenger intercom pairing up
Make sure the M5 is turned off;
Put both systems in Setting mode (press the “BACK” key and keep it pressed for 4 seconds,
until the red LED starts to flash quickly);
Press the “n” key briefly on one of the systems (Channel 1 pairing up);
A “wait for connection” tone is emitted until the pair up procedure is not completed.
12.2. Rider-Passenger intercom function
After carrying out the proper pair up procedure, turn on the two helmets. To activate the intercom
connection, starting from an N-Com system that has already been turned on, briefly press key "n".
Manual intercom connection With M5 turned on, briefly press “n”.
Manual intercom
disconnection With M5 turned on, briefly press “n”.

M5
17
13. BIKE-TO-BIKE INTERCOM
The N-Com system is used for bike-to-bike communication up to a distance of about 500 m (open
terrain, no obstacles). For proper operation of bike-to-bike communication, you need to open the
antennas of the e-box M5, as shown in the figure.
Fig. 20 Fig. 21
The M5 system entails the use of a default “STANDARD” commands configuration, or the use of a
“FRIENDS” configuration that can be turned on from the N-Com Wizard or dedicated App.
The difference between the two configurations lies in the number of motorcycles that can be hooked
up: the STANDARD configurations allows up to 3 different motorcycles to be hooked up to the M5
system, while the FRIENDS configurations allows up to a total of 6.
Important: If you use the FRIENDS configuration, you need to visit the N-Com website and download
the dedicated commands diagram (section Download/Command Summary Diagram).
N.B.: The range and quality of the communication may vary significantly depending on the presence
of obstacles, weather conditions, magnetic fields.
N.B.: The range of the communication varies depending on the N-Com systems used.
13.1. Bike-to-Bike Intercom Affiliation (Standard configuration)
Make sure the M5 is turned off;
Put both systems A and B in Setting Mode (press the “BACK” key and keep it pressed for 4
seconds, until the red LED starts to flash quickly);
On system A, press the command related to the “setting position” where you wish to store
system B;
Pairing up CHANNEL 1 Briefly press “n”.
Pairing up CHANNEL 2 Press the “n” key twice.
Pairing up CHANNEL 3 Press the “n” key three times.
Pairing up CHANNEL 4 Briefly press “ on ”.
Pairing up CHANNEL 5 Press the “ on ” key twice.
Pairing up CHANNEL Press the “ on ” key three times.
N.B.: Channels 4-5-6 can be paired up and used only by activating the FRIENDS configuration.

EN
18
CHANNEL 1 is typically used for the Rider-Pillion Passenger connection, however it can also be used
for the Bike-to-Bike intercom.
The use of CHANNEL 1 is different from the other channels due to the following specific characteristics:
By pressing key "n", the intercom connection is automatically activated.
The Phone Conference function and the GPS Conference function can be used.
13.2. Bike-to-Bike intercom function
How the Bike-to-Bike call works (Standard Configuration)
Connection CHANNEL 1 Briefly press “n”.
Call CHANNEL 2 Press the “n” key twice.
Call CHANNEL 3 Press the “n” key three times.
Disconnection of active intercom Briefly press “n”.
With FRIENDS CONFIGURATION active:
Call CHANNEL 4 Briefly press “ on ”.
Call CHANNEL 5 Press the “ on ” key twice.
Call CHANNEL 6 Press the “ on ” key three times.
Disconnection of active intercom Briefly press “ on ”.
N.B.: In case the memory setting is empty, or the other helmet cannot be reached, an error tone will
sound in your helmet.
Taking a Bike–to-Bike call
Four calling tones will sound in the helmet receiving the Bike-to-Bike call (channel 2-6), and all open
audio functions will be temporarily cut off (including the Rider – Pillion Passenger intercom, if any).
Answering a Bike-to-Bike phone call Briefly press any key when you hear the incoming call signal.
In case you take the call, communication is automatically established.
In case the call is not answered, the system returns to the situation prior to receiving the call.

M5
19
14. SETTING MODE
All Bluetooth pair ups and other adjustments are carried out in this mode.
To put the system in Setting mode (system turned off), press the “BACK” key and keep it pressed for 4
seconds, until the red LED starts to flash quickly.
n on
N
+
on
▲▼
▲
+
▼
BACK
Turning on/off the RDS x1
Turning on/off the Smart Navi System
2 sec
Pairing up Secondary Phone 2 sec
Pairing up CHANNEL 1 x1
Pairing up CHANNEL 2 x2
Pairing up CHANNEL 3 x3
Pairing up CHANNEL 4 X
Pairing up CHANNEL 5 x2
Pairing up CHANNEL 6 x3
Pairing up the wireless keypad 10 sec
Reset 4 sec
*With Friends Configuration active.
15. BATTERY AND RECHARGE
15.1. Low battery signal
During its operation, the system alerts the user with a voice message when the battery is low. From
the first message, the system has a 1-hour autonomy. Warning is given every 10 minute.
15.2. Charging the system
To charge the system, hook it up to the battery charger or to a USB outlet powered with the USB-mini
USB cable supplied as standard equipment. The charge will take place as follows:
Fig. 22
When you connect the M5 system to the
battery charger, the red LED of the
Emergency Stop Light stars to flash (at a
frequency of 10 seconds).
When the battery is fully charged, the red
LED turns off.
N.B.: If the device has not been charged for a long time (a few months), it may not be possible to turn
on the system during the first few minutes of the charging, as the voltage may drop below the
minimum limit.

EN
20
16. SUMMARY TABLE OF CONTROLS – STANDARD CONFIGURATION
Button
n on
N
+
on


+

BACK
Turning on X
Turning off 2 sec
Increase Volume X
Decrease Volume X
Basic Functions
Turning on/off the
Emergency Stop Signal X
Answer phone call X X X X
Voice call 2 sec
Redial last number X
Dial Friend Number 2 sec
Hang up/reject a phone
call 2 sec
Call transfer 2 sec
Manual Device
Connection 2 sec
Manual Device
Disconnection 4 sec
Turning on the
Conference function X
Bluetooth Devices
Turning off the
Conference function X
Connection CHANNEL 1 X
Disconnection of active
intercom X
Calling CHANNEL 2 x2
Calling CHANNEL 3 x3
Calling CHANNEL 4** X
Calling CHANNEL 5** x2
Intercom
Calling CHANNEL 6** x3