Nags Head Hammocks CUMARU User manual

STEP 1. Use (2) 2.5” hex bolts, (4) washers and (2) lock nuts secure
swing body.
CUMARU HANGING
HAMMOCK CHAIR
INSTRUCTIONS
• SWING BODY
• MALLET
(2) 2.5” HEX BOLT
(4) WASHERS
HARDWARE PACK
SWING PARTS
SUGGESTED TOOLS
ASSEMBLY
SWING BODYSWING BODY
2.5” HEX BOLT2.5” HEX BOLT
WASHERWASHER
(2) LOCK NUTS
• SPREADER BAR
• 7/16” WRENCH
• (1) EXTENSION CHAIN
• (1) QUICK LINK
LOCK NUTLOCK NUT
Hardware Pack Weight: 1 lb 4.2 oz.
0QUICK LINKQUICK LINK
EXTENSION CHAINEXTENSION CHAIN
SPREADERSPREADER
BARBAR
STEP 2. Run remaining end
through spreader bar hole and
attach to quick link. Repeat
for other side. (Rope not
pictured.)

Congratulations on purchasing this Original Cumaru Captain’s Chair. QUESTIONS
REGARDING THIS PRODUCT? Call our customer service team,
252-295-0405.
MAINTENANCE - Sunwax Penetrating Wood FeederTM is recommended as an added
protection for wood from insects and weather. It is ideal for cumaru, revitalizes the
look of older wood and helps maintain wood’s original hue. To clean rope use soap,
detergent or a mild bleach solution. Use a soft bristled scrub brush to work on any
stains. Be sure to rinse the ropes thoroughly after cleaning.
Periodically check bolts after assembly and re-tighten when necessary.
WARRANTY & RETURNS - Nags Head Hammocks products are guaranteed to be free of
defects in both workmanship and material. Prolonged exposure to weather conditions
including snow, rain, and humidity are not covered under the warranty, nor is damaged
caused by normal wear, mildew, or improper care, including storage, maintenance, and
assembly. If you are not satisfied with an item, return it unused in its original packaging
for a complete refund or exchange. You can return it to any of our stores or to our
warehouse, Nags Head hammocks, 305 Industrial Blvd., Greenville, NC 27834. Please
include a copy of your receipt and your contact information.
5060NH
HANGING YOUR SWING
FROM A WOODEN BEAM
STEP 1. Choose a hanging location for your swing 6.5-8.5
feet above ground/floor level that will safely support
350 pounds. Note that hanging it much higher will
require additional hardware not included with the swing.
The hanging bracket should ONLY be used with wood;
it’s NOT safe or approved for use with concrete or steel
surfaces, plastic construction, particle board or other
composite material, or vinyl siding. For installing in any other surface but wood,
consult a building expert for advice on proper installation, including questions
about weight capacity of a potential installation surface. Hatteras Hammocks is
not responsible for improper installation.
STEP 2. Position the hanging bracket along the center of your chosen wood
beam. Mark drill holes on the beam using a pencil through the bracket’s two bolt
holes.
STEP 3. Drill approximately 2.5 inches deep at the spots marked through the
bolt holes.
STEP 4. Fit the narrow end of the S-Hook onto the hanging bracket
BEFORE bracket installation; the S-Hook will NOT fit onto the bracket once
the bracket is installed. Next, position the bracket holes over the drill holes,
and install the two bolts by hand. Tighten the bolts with a 7/16” wrench or
socket, or adjustable wrench. Do not over tighten, as bolts can strip the wood,
compromising the swing’s weight capacity.
STEP 5. To now hang your swing, hook one link of the Extension Chain to the
bottom of the S-Hook on the Hanging Bracket Assembly.
STEP 6. When sitting in your swing, your feet should touch the ground with
your knees slightly bent. Fine-adjust the height of your swing by changing the
link of Extension Chain you use for hanging.
INSTALLED
BRACKET,
S-HOOK