Nags Head Hammocks Double deluxe swing User manual

DOUBLE DELUXE SWING
INSTRUCTIONS
• Rubber Mallet
• Adjustable Wrench • Phillips Head Screwdriver
(6) Barrel Nuts
(15) Locknuts
(1) Allen Wrench
(30) Washers
(7) 5” Hex Bolts
(8) 3.5” Hex Bolts
(2) Tree Hooks and
chain sets
(4) 4.5” Barrel Bolts
(2) 4” Barrel Bolts
• CHAIN SETS: (2)
Eye Bolts, nuts, and washers attached
HARDWARE PACK
CHAIN SET SUGGESTED TOOLS
LONGLONG
CHAINCHAIN
FRONTFRONT
SHORTSHORT
CHAINCHAIN
FRONTFRONT
5.5” EYE5.5” EYE
BOLTBOLT
4” EYE4” EYE
BOLTBOLT
NOTE. Add chains after
completeing assembly.
NOTE. Instructions not to scale.
ASSEMBLY
STEP 1. Align left arm with swing body. Insert 3.5” Hex Bolt through
washer, arm and swing body. Secure using washer and lock nut, repeat
this process for all 3 holes both left and right side.
NOTE. do not tighten bolts until Step 4.
3.5” Hex Bolt
Lock Nut

ASSEMBLY
STEP 2. Position an upright as shown and secure it with (2) 3.5” Hex bolts
and a washer on each side of the material. Repeat for the other side.
STEP 3. Attach front and rear table legs to the center table
using (2) 5” Hex Bolts, a washer on each side of the material
and a lock nut as shown.
Note : Rear legs are longer than the front.
STEP 4. Place the center table in the frame as shown, use (3) 5” Hex
bolts, a washer on each side of the material and a lock nut to secure the
front and rear legs to the center frame.
STEP 5. Attach center upright with (2) 5” Hex Bolts with a washer on
each side of the material and secure with a locknut.
Barrel Nut
Lock Nut
Lock Nut
Lock Nut
Lock Nut
3.5” Hex Bolt
4” Barrel Bolt
5” Hex Bolt
5” Hex Bolt
5” Hex Bolt

ASSEMBLY
STEP 6. Position rollup as shown and secure it with (4) 4.5”
Barrel Bolts, starting with the center upright.
STEP 7. Attach long bolt of Chain Assembly in the hole on the top of the
rollup, by first unscrewing the nut and removing 1 washer. Thread bolt
with one washer through the frame and secure with washer and locknut.
Repeat for the right side, then repeat for the front using holes in the
frame as shown. Insert plastic drink holders.
Make sure to tighten all bolts then hang the swing using the included
tree hooks or two other properly installed hooks - spacing hooks
approximately 50-54” apart.
Enjoy your new Nag’s Head Deluxe Double Swing!
Congratulations on purchasing this Original Nag’s Head Deluxe Double Swing. QUESTIONS REGARDING THIS PRODUCT? Call our customer service team, 252-295-0405.
INSTALLATION - Get somebody to help you, some pieces are heavy and a second pair of hands is always helpful. Do not tighten bolts until the product is fully assembled. Some pieces are harder to fit in place and this will help. A hammer
or rubber mallet is needed during assembly. Do not over-tighten the bolts or screws. Build your item close to where it will be used to eliminate diculty in moving once completed. For a uniform look, face all nuts in the same direction.
MAINTENANCE - Great care has been put into manufacturing this item. However, it is made of high density resin and some natural esthetic imperfections and dark spots are normal and should be expected. You can wash the wood and
the rope using a hose and some bleach water. You can also brush the wood to help remove dirt.
WARRANTY & RETURNS - Nags Head Hammocks products are guaranteed to be free of defects in both workmanship and material. Prolonged exposure to weather conditions including snow, rain, and humidity are not covered under the
warranty, nor is damaged caused by normal wear, mildew, or improper care, including storage, maintenance, and assembly. If you are not satisfied with an item, return it unused in its original packaging for a complete refund or exchange.
You can return it to any of our stores or to our warehouse, Nags Head hammocks, 305 Industrial Blvd., Greenville, NC 27834. Please include a copy of your receipt and your contact information.
Barrel Nut
4.5” Barrel Bolt
Lock Nut
#5113NHR1
5.5” EYE5.5” EYE
BOLTBOLT
4” EYE4” EYE
BOLTBOLT