Nags Head Hammocks Single Rope Swing User manual

Single Rope Swing
Congratulations on your purchase. You now have one of Nags
Head Hammocks’ innovative products! If you have any ques-
tions regarding this product, we invite you to call us 7 days a
week at 800-344-6433.
Helpful tips before starting: • Get someone to help you. Some
pieces are heavy and a second pair of hands always helps. •
Do not tighten the bolts completely until the product is fully
assembled. Some pieces are harder to fit in place and this will
help. A hammer or rubber mallet is needed during assembly.
• Do not over-tighten the bolts or screws. • Build your item
close to where it will be used to eliminate difficulty in moving
once completed. • For a uniform look, face all nuts in the same
direction.
Step 1. Set Rollup on flat surface such as a work table. Align holes of Left
Arm with holes located on the side of the Rollup. FIGURE 1
Hardware 8 - 3.5” x ¼Hex Bolt
2 - 4” x ¼” Barrel Bolt
2 - 4.5” x ¼” Barrel Bolt
4- ¾” Barrel Bolt Fasteners
8 - ¼” Locknuts
16 - ¼” Washer
1 - Allen Wrench
2 - Chain Assemblies
2 - Tree Hooks
Step 2. Starting with back hole of Arm, thread 3.5” Bolt through Washer,
through Arm and Rollup. Secure with Washer and Locknut. Repeat
process for holes at front of Arm. Note: This step may require a Mallet to
tap Bolts through. FIGURE 2
Step 3. Repeat Step 2 for Right Arm.
FIGURE 1
FIGURE 2
Parts: Swing Roll-up
Left Arm
Right Arm
Left Upright
Right Upright
Cup
Holder
Front of rollup
Spacer Bar
SUGGESTED TOOLS
(NOT PROVIDED)
• Rubber Mallet
•Standard Phillips Head Screwdriver
•Adjustable Wrench

Care Instruction and Tips: Great care has been put into manufacturing this item. However, it is made of high density resin and some natural esthetic imperfections and
dark spots are normal and should be expected. You can wash the wood and the rope using a hose and some bleach water. You can also brush the wood to help remove
dirt. *These instructions are also available at www.nagsheadhammocks.com/assembly_instructions.asp Warranty: Products of Nags Head Hammocks are guaranteed to
be free of defects in workmanship or material. We will replace defective parts for free. Simply call us and we will see that you get what you need. Prolonged exposure
to weather conditions including snow, rain, and humidity are not covered under the warranty nor is damage caused by normal wear, mildew, improper care including
storage, maintenance, and assembly. Returns: Nags Head Hammocks has a money back guarantee. If you are not satisfied with an item, return it unused in its original
packaging for a complete merchandise refund or exchange. You can return it to any store or to our warehouse, Nags Head Hammocks, 305 Industrial Bd., Greenville,
NC 27834. Please include a copy of your receipt and your contact information. Nags Head Hammocks, PO Box 533, Nags Head, NC 27959
Inst # 5081 Rev 7/16
FIGURE 9
Step 4. Locate Left Upright and place on rollup as shown. Thread 3.5”
hex bolt through washer, Left Arm, Left Upright. Secure loosely with
washer and Locknut. FIGURE 3
FIGURE 3
Step 5. Rotate Left Upright to align with top hole in Left Arm. Thread
4” Barrel Bolt through hole. Secure loosely with Barrel Bolt Fastener.
FIGURE 4
Step 6. Repeat Steps 4-5 for Right Side.
Step 7. Place a 4.5” Barrel in both bottom holes of Rollup and seed into
bottom holes of Uprights. Secure with Barrel Bolt Fasteners. FIGURE 5
FIGURE 4
Step 10. Tip swing onto back and using longest length of chain assembly,
thread bolt through Washer, through left hole at front of Rollup. Secure
using washer and Locknut. FIGURE 7
FIGURE 5
FIGURE 6
FIGURE 7
Step 11. After returning Swing to upright position, locate the Spacer Bar
and thread through holes in remaining chain assembly. FIGURE 8
Step 12. Insert Cup Holder. FIGURE 9
Step 13. Tighten all bolts securely.
Step 14. Hang swing after properly securing with included tree hooks
(Spaced approximately 25” - 30” apart), or from your existing hooks.
Step 15. Enjoy your new Nags Head Hammocks Swing.
Step 8. Using shortest length of chain assembly, thread bolt through
Washer, through upper left hole in Rollup and Upright. Secure using
washer and Locknut. FIGURE 6
Step 9. Repeat Step 8 for right side.
FIGURE 8