Napoleon High Country NZ7000 User manual

EN
W415-1277 / 08.12.15
FR
PG
45
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
1.44A
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.napoleonfireplaces.com •[email protected]
SAFETY INFORMATION
If the information in these instructions are not followed
exactly, a fire or explosion may result causing property
damage, personal injury or death.
Please read entire manual before you install and use your
fireplace.
This fireplace has not been tested with an unvented gas log
set. To reduce risk of fire or injury, do not install an unvented
gas log set into the appliance.
- This appliance can be very hot when burning.
- Combustible materials such as firewood, wet clothing, etc.
placed too close can catch fire.
- Children and pets must be kept from touching the appliance
when it is hot.
- The chimney must be sound and free of cracks. Before
installing this unit, contact the local building or fire authority
and follow their guidelines.
- Burn wood behind the log retainer directly on the firebricks.
- Do not use an elevated grate or otherwise raise the fire.
- This appliance is designed to burn natural wood only. Lower
emissions generally result when burning air dried seasoned
hardwoods, as compared to softwoods or to green or freshly cut
hardwoods.
- Do not start a fire with chemicals or fluids such as gasoline,
engine oil, etc.
- Do not burn treated wood, coal, charcoal, coloured paper,
cardboard, solvents or garbage.
- Do not let the appliance become hot enough for any part to
glow red.
$10.00
!WARNING
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
NZ7000 / NZ8000
QUALIFIED CLEAN BURNING
DECORATIVE FIREPLACE
THIS APPLIANCE HAS BEEN SAFETY TESTEDAND LISTED BY INTERTEK TESTING SERVICES LTD. AS PER THE STANDARDS: ULC S610, UL 127 U.S. EPA LOW
MASS WOOD-BURNING FIREPLACE VOLUNTARY PROGRAM PHASE 2 EMISSION LEVELQUALIFIED MODEL.
NZ8000 ILLUSTRATED

W415-1277 / 08.12.15
2
EN
TABLE OF CONTENTS
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 GENERAL INSTRUCTIONS 6
2.3 GENERAL INFORMATION 8
2.3.1 FEATURES 8
2.3.2 THIS CORDWOOD FUEL FIREPLACE 8
2.3.3 PACKING LIST 8
2.4 RATING PLATE INFORMATION 9
3.0 INSTALLATION PLANNING 10
3.1 LOCATION AND CLEARANCES 11
3.1.1 VENTILATION OPENINGS 11
3.2 OUTSIDE COMBUSTION AIR 12
3.3 FLOOR PROTECTION 13
3.3.1 EMBER STRIPAND HEARTH EXTENSIONS 13
3.3.2 HEARTH EXTENSION 14
3.3.3 HEARTH EXAMPLES 15
4.0 INSTALLATION 16
4.1 CHIMNEY 16
4.2 TYPICAL CHIMNEY INSTALLATION 17
4.3 ADDING CHIMNEY SECTIONS 18
4.4 OFFSETCHIMNEYINSTALLATION 19
4.5 INSTALLING FLASHINGAND STORM COLLAR 20
4.6 AIR COOLED CHIMNEY INSTALLATION 20
5.0 FRAMING 21
5.2 FINISHING MATERIAL 22
5.3 MINIMUM CLEARANCE TO COMBUSTIBLES 23
5.4 MINIMUM ENCLOSURE CLEARANCES 23
5.6 MINIMUM MANTEL CLEARANCES 24
6.0 FINISHING 25
6.1 DOOR & SCREEN OPERATION 25
6.3 DOOR GLASS REPLACEMENT 26
6.4 SCREEN REPLACEMENT 26
6.5 BALANCE WEIGHTADJUSTMENT 27
6.6 FIREBRICK INSTALLATION AND DAMPER OPERATION 28
7.0 SELECTING WOOD 29
8.0 OPERATION 30
8.1 OPERATING SOUNDS AND SMELLS 30
8.2 STARTING THE FIRE 31
8.3 FIRE EXTINGUISHERS AND SMOKE DETECTORS 32
8.4 FUEL LOADINGAND BURN CYCLE 32
8.5 STARTING THE FIRE (DAMPER OPEN) 33
8.6 SMOKING 34
8.7 RELOADING THE APPLIANCE 34
9.0 MAINTENANCE 34
9.1 ASH REMOVAL PROCEDURES 34
9.2 CREOSOTE FORMATION AND REMOVAL 34
9.3 RUN-AWAY OR CHIMNEY FIRE 35
9.4 CHIMNEY CLEANING 36
9.5` CARE OF GLASS 36
10.0 REPLACEMENTS 37
11.0 TROUBLESHOOTING 42
12.0 WARRANTY 43

W415-1277 / 08.12.15
3
EN
1.0 INSTALLATION OVERVIEW
THIS APPLIANCE AND ITS COMPONENTS ARE DESIGNED TO BE INSTALLED AND OPERATED
AS A SYSTEM. ANY ALTERATION TO OR SUBSTITUTION FOR ITEMS IN THIS SYSTEM, UNLESS
ALLOWED BY THESE INSTALLATION INSTRUCTIONS, WILL VOID THE ETL LISTING AND MAY VOID
THE PRODUCT WARRANTY. IT MAY ALSO CREATE A HAZARDOUS INSTALLATION. READ THROUGH
THESE INSTRUCTIONS THOROUGHLY BEFORE STARTING YOUR INSTALLATION AND FOLLOW
THEM CAREFULLY THROUGHOUT YOUR PROJECT.
Hearth, see “HEARTH
EXTENSION” section
Rating plate, see “RATING
PLATE INFORMATION”
section
Firebrick, see “FIREBRICK
INSTALLATION” section
Framing, see “FRAMING”
section
Chimney, see “CHIMNEY
INSTALLATION” section
Mantel, see “MINIMUM
MANTEL CLEARANCES”
section

W415-1277 / 08.12.15
4
EN
3.17E
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND
IS PROHIBITED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
according to operating instructions could cause fire or injury.
• Before installing this appliance, contact the local building or fire authority and follow their guidelines.
• This appliance must be installed by a qualified installer.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not operate without fully assembling all components.
• Do not let the appliance become hot enough for any part to glow red.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges
may be sharp.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid
burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if
there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety
gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance. Objects placed in front of
the appliance must be kept a minimum of 48” (1219.2mm) away from the front face of the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot
surfaces. These screens and guards must be fastened to the floor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe servicing a separate solid fuel burning appliance.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should
be done by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• Only doors / optional fronts certified with the unit are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all
plastic bags, these are not toys and should be kept away from children and infants.
• If the appliance is not properly installed, a house fire may result. Do not expose the appliance to the elements
(ex. rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when the appliance
is used.
• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.
• Do not start a fire with chemicals or fluids such as gasoline, engine oil, etc.
• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to
smoke spillage in your home.
• Lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or too
green or freshly cut hardwoods. Burning wet unseasoned wood can cause excessive creosote accumulation.
When this is ignited it can cause a chimney fire that may result in a serious house fire.
• This appliance is designed to burn natural wood only. Do not burn trash or garbage, lawn clippings / waste,
rubber, waste petroleum products, paints or paint thinners / solvents, plastic, materials containing asbestos,
construction debris, railroad ties or treated wood, manure or animal remains, salt water driftwood or salted
materials, unseasoned wood, coal, charcoal, coloured paper, cardboard, plywood or particleboard. Burning
these materials may result in release of toxic fumes or render the appliance ineffective and cause smoke.
• Burn wood directly on the firebricks. Do not elevate grate or otherwise raise the fire.
• Do not store wood within appliance installation clearances or within the space required for re-fueling and ash
removal.
• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away
from the home or structure until completely cool.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or
damage to decorations, a T.V. or other electronic components.
2.0 INTRODUCTION

W415-1277 / 08.12.15
5
EN
2.1 DIMENSIONS
40 1/8"
1020mm
14 3/8" 365mm
4 7/8"
124mm
Ø8" 203mm
59 5/8" 1514mm
NZ8000 ILLUSTRATED
78 3/4"
2000mm
80 3/4"
2053mm
31 1/8"
791mm
29 1/16" 738mm
14 3/8" 365mm
Ø8" 203mm
46 3/8" 1178mm
59 5/8" 1514mm
NZ7000 ILLUSTRATED
4 7/8"
124mm
46 3/8" 1178mm
29 1/16" 738mm
5"
127mm
*
*
*
*
**
**
**
**
** SCREWS MUST NOT PENETRATE MORE
THAN 1/2" IN LENGTH IN THIS AREA
NO SCREWS IN THIS AREA
*
**SCREWS MUST NOT PENETRATE MORE
THAN 1/2" IN LENGTH IN THIS AREA
NO SCREWS IN THIS AREA
*
*
*
**
**
**
**
*
*
*
*
*
*
80 3/4"
2053mm
78 3/4"
2000mm
5"
127mm
61 7/8" 1572mm
61 7/8" 1572mm
31 5/16" 795mm
31 5/16" 795mm
*
**SCREWS MUST NOT
PENETRATE MORE THAN 1/2"
IN LENGTH IN THIS AREA
NO SCREWS IN THIS AREA
NZ8000 ILLUSTRATED
**
**
** *
*
*
*
*
*

W415-1277 / 08.12.15
6
EN
2.2 GENERAL INSTRUCTIONS
BEFORE INSTALLING THIS APPLIANCE, CONTACT THE LOCAL BUILDING OR FIRE AUTHORITY AND
FOLLOW THEIR GUIDELINES.
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. FOLLOW THE INSTALLATION
DIRECTIONS. DO NOT OPERATE WITHOUT FULLY ASSEMBLING ALL COMPONENTS.
IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT.
DO NOT EXPOSE THE APPLIANCE TO THE ELEMENTS (EX. RAIN, ETC.) AND KEEP THE APPLIANCE
DRY AT ALL TIMES. WET INSULATION WILL PRODUCE AN ODOUR WHEN THE APPLIANCE IS USED.
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
CHILDREN AND PETS MUST BE KEPT FROM TOUCHING THE APPLIANCE WHEN IT IS HOT. CON-
TACT YOUR LOCAL AUTHORIZED DEALER / DISTRIBUTOR FOR SAFETY SCREENS THAT MAY BE
AVAILABLE FOR THIS PRODUCT.
COMBUSTIBLE MATERIAL SUCH AS FIREWOOD, WET CLOTHING, ETC. PLACED TOO CLOSE CAN
CATCH FIRE. OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48"
(1219.2MM) FROM THE FRONT OF THE APPLIANCE.
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE
WITH LOCAL CODES AND WITH THE NATIONAL ELECTRIC CODE ANSI/NF NO. 70-CURRENT (IN THE
UNITED STATES), OR WITH THE CURRENT CSA C22.1 CANADIAN ELECTRIC CODE (IN CANADA).
NOTE: It is recommended to test the listed components below before installation:
- Doors
- Balance weights
- Louvre for air intake
All components should be in good operating condition before the unit is installed.

W415-1277 / 08.12.15
7
EN
2
3
3
1
1. Combustion air is brought into the appliance through the slots and around the glass door or through
the screen.
2. A single air control regulates the amount of the outside air introduced to the unit.
3. Inside the firebox combustion takes place and exhausts out the chimney.

W415-1277 / 08.12.15
8
EN
2.3 GENERAL INFORMATION
2.3.1 FEATURES
Shipped with appliance:
Installation manual
Ember Strip
Approximate Heating Capacity up to 1,000 square feet (92 square meters).
CALIFORNIA PROP 65 WARNING:
Use of this product may produce smoke which contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
Do not use makeshift compromises during installation.
Do not block or restrict air, grille or louvre openings! Do
not add a hood.
Burning your appliance with the door open or ajar creates a fire hazard that may result in a house and/or
chimney fire.
All venting connections must be in compliance with the chimney manufacturers installation instructions.
Clearances referred to throughout this manual are the minimum requirements.
Your appliance must be installed in accordance with all national and local building code standards and
the standard of Chimney and Appliances, Vents and Solid Fuel Burning Appliances NFPA #211. Consult
the authority having jurisdiction (such as municipal building department, fire department, fire prevention
bureau, etc.) to determine the need to obtain a permit. If you are in doubt about the proper installation for
your situation, contact your dealer or local building or fire official. The manufacturer does not guarantee
that this appliance and its options will completely heat your entire home.
Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.
It is recommended that in all cases, the appliance be secured to the floor. Use the pallet packing brackets
to accomplish this.
THISAPPLIANCE HAS BEEN EPA QUALIFIED.
• Depending on the loading method and size of log,
maximum length of 32" (813mm).
• Large glass door for maximum visibility.
• Fully refractory lined firebox.
• Closable outside air for combustion.
• Closable damper.
• Shipping weight 1150lbs (521kg).
• Flue outlet diameter 8" (203mm).
• Max fuel load 60lbs (27kg).
• Max fuel height, halfway or top of the first firebrick.
DO NOT LET THE APPLIANCE BECOME HOT ENOUGH FOR ANY PART TO GLOW RED.
2.3.2 THIS CORDWOOD FUEL FIREPLACE
2.3.3 PACKING LIST

W415-1277 / 08.12.15
9
EN
2.4 RATING PLATE INFORMATION
Rating plate is located behind the faceplate door. Hardware on the right.
This illustration is for reference only. Refer to the rating plate on the
appliance for accurate information.
RATING
PLATE
LOCATION
CERTIFIED TO / CERTIFIÉ SELON: ASTM E2515,ASTM E2558, UL S610, UL-127
9700539 (WSL)
4001657 (NGZ)
4001658 (NAC)
4001659 (WUSA)
MODEL NO.NZ7000 / NZ8000 /
LISTED FACTORY BUILT FIREPLACE MODEL. PHASE 2 EMISSION LEVEL QUALIFIED. /
FOYER PRÉFABRIQUÉ HOMOLOGUÉ. LA PHASE 2 NIVEAU QUALIFIÉ D'ÉMISSION
NZ7000
N° DE MODÈLE NZ7000 / NZ8000
INSTALL AND USE ONLY IN ACCORDANCE WITH WOLF STEEL LTD. INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL. CONTACT LOCAL BUILDING OR FIRE OFFICIALSABOUT RESTRICTIONS
AND INSTALLATION INSPECTION IN YOURAREA. DO NOT CONNECT THIS UNIT TOA CHIMNEY
SERVING ANOTHER APPLIANCE.
POUR INSTALLATION ET UTILISATION CONFORMÉMENT AUX MANUEL WOLF STEEL LTD.
RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES DU BÂTIMENT OU DU SERVICE DES
INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS D'INSTALLATION DANS VOTRE
RÉGION. NE PAS RACCORDER À LA CHEMINÉE D'UNAUTRE APPAREIL.
24 NAPOLEON ROAD. BARRIE, ONTRAIO L4M 0G8 CANADA
COMPONENTS REQUIRED FOR INSTALLATION:
CHIMNEY REQUIREMENTS (see installation manual):
SHIPPED WITH THE FIREPLACE:
INSTALLATION MANUAL
EMBER STRIP
Chimney must be certified to one of the following standards ULC S629 for Canada or UL 103HT for the
United States. Masonry chimney installation: Stainless steel liner must be certified to ULC S640 M92 or ULC
639 for Canada or UL 1777 for the United States.
Air cooled chimney: Use only DuraVent DuraPlus
MINIMUM CHIMNEY HEIGHT 15 ft (4.57 m) MAXIMUM # OF ELBOWS 4
MAXIMUM CHIMNEY HEIGHT 40 ft (10.36 m) FLUE COLLAR 8"ø
MAXIMUM OFFSETANGLE 30º US - 45º CANADA
W385-1929
COMPOSANTS REQUIS POUR L'INSTALLATION:
EXIGENCES POUR LA CHEMINÉE (voir le manuel d'instructions)
La cheminée doit être certifiée selon l'une des normes suivantes : ULC S629 pour le Canada ou selon les
normes UL 103HT pour les États-Unis. Installation de la cheminée de maçonnerie: revêtement en acier
inoxydable doit être certifié à la norme ULC S640 M92 ou ULC 639 pour le Canada ou UL 1777 pour les
États-Unis. Cheminée refroidie à l'air:
Utilisez seulement DuraVent DuraPlus.
LIVRÉ AVEC LE FOYER:
MANUEL D'INSTRUCTIONS
PARE-BRAISES
HAUTEUR MINIMALE DE LA CHEMINÉE 15 pi (4.57 m) # MAXIMAL DE COUDES: 4
HAUTEUR MAXIMALE DE LA CHEMINÉE 34 pi (10.36 m) BUSE D'ÉVACUATION: 8"ø
ANGLE DE DÉVIATION MAXIMAL 30º US - 45º CANADA
PREVENT CREOSOTE FIRE: INSPECT CHIMNEYAND
CHIMNEY CONNECTOR, IFAPPLICABLE, TWICE MONTHLY
AND CLEAN IF NECESSARY. DO NOT OVERFIRE: IF
EXTERIOR OF UNIT GLOWS RED, YOUARE OVERFIRING.
KEEP FURNISHINGSAND OTHER COMBUSTIBLE MATERIALS
A CONSIDERABLE DISTANCE AWAY FROM APPLIANCE. TYPE
OF FUEL: SOLID WOOD ONLY./PREVENIR LES FEUX DE
CREOSOTE: INSPECTEZ LA CHEMINEE OU LE RACCORD DE
CHEMINEE, SI APPLICABLE, DEUX FOIS PAR MOIS ET
NETTOYEZ SI NECESSAIRE. NE SURCHAUFFEZ PAS: SI
L'EXTERIEUR DE L'UNITE DEVIENT ROUGE, VOUS
SURCHAUFFEZ. GARDEZ LES MEUBLES ETAUTRES
MATERIELS COMUSTIBLES AUNE DISTANCE
CONSIDERABLE DE L'APPAREIL DE CHAUFFAGE. TYPE DE
COMBUSTIBLE: SOLIDE BOIS SEULEMENT.
IMPORTANT: BEFORE COMMENCING INSTALLATION
REFER TO THE LABEL LOCATED BEHIND THE
FACEPLATE AND TO THE MANUFACTURER'S
INSTALLATION INSTRUCTIONS PACKAGED TOGETHER
WITH THIS UNIT. THE INSTALLATION MUST BE
APPROVED BY THEAUTHORITY HAVING JURISDICTION./
AVANT DE COMMENCER L'INSTALLATION,
REFEREZ-VOUS À L'ÉTIQUETTE QUI SE TROUVE
DERRIÈRE LA FAÇADE AINSI QU'AUX INSTRUCTIONS
D'INSTALLATION DU MANUFACTURIER FOURNIES AVEC
L'UNITÉ. L'INSTALLATION DOIT ÊTRE APPROUVÉE PAR
L'AUTORITÉ COMPÉTENTE.
NZ8000
NZ7000 AVERAGE
EMISSION / EMISSION
MOYENNE 3.1 g/kg
AVERTISSEMENT:
3RXUXQHXWLOLVDWLRQDYHF
les portes complètement
ouvertes et complètement
fermées. Remplacer verre
céramique seulement
uniquement avec verre
céramique obtenue auprès
du concessionnaire et
certifiés pour une
utilisation avec cet
appareil.
1HSHXWrWUHLQVWDOOpGDQV
une maison mobile.
WARNING:
)RUXVHZLWKGRRUVIXOO\
opened and doors fully
closed. Replace ceramic
glass only with ceramic
glass obtained from the
dealer and certified for
use with this appliance.
1RWIRUXVHLQD0RELOH
Home.
NZ8000 AVERAGE
EMISSION / EMISSION
MOYENNE 2.2 g/kg
This model meets the U.S. EPA Wood-burning Fireplace Program Phase 2 emission level. To minimize smoke, always operate
your fireplace in accordance with the manufacturer’s instructions found in the owner’s manual.Additional information about
EPA’s Program is available at www.epa.gov/burnwise/index.html / Ce modèle répond à la Cheminée programme de phase de
niveau 2 des émissions États Unis EPA à bois. Pour minimiser la fumée, toujours fonctionner votre foyer conformément aux
instructions du fabricant figurant dans le manuel du propriétaire. Des renseignements supplémentaires sur le programme de
l'EPA est disponible à www.epa.gov/burnwise/index.html
NE LIVRÉ AVEC LE FOYER:
BRIQUE RÉFRACTAIRE
NZ7000 / NZ8000
QUALIFIED EPA PHASE 2 MODEL UNTIL MAY 2017 /
QUALIFIÉ EPA PHASE 2 MODÈLE JUSQU'À MAI 2017.
2017
Apr/Avr. Jul/Juill. Oct/Oct.
May/Mai Aug/Août. Nov/Nov.
Jun/Juin Sep/Sept. Dec/Déc.
MODEL CERTIFCATION DATE / DATE DE CERTIFICATION DU MODÈLE:
Jan./Jan.
Feb./Fév.
Mar./Mars.
2015 2016
NOT SHIPPED WITH THE FIREPLACE:
REFRACTORY BRICKS
WARNING:THISAPPLIANCE HAS NOT BEEN TESTED WITH
AN UNVENTED GAS LOG SET. TO REDUCE RISK OF FIRE
OR INJURY, DO NOT INSTALL AN UNVENTED GAS LOG SET
INTO APPLIANCE. / AVERTISSEMENT: CET APPAREIL N'A
PAS ÉTÉ TESTÉ AVEC DES BÛCHES À GAZ. POUR
RÉDUIRE LES RISQUES D'INCENDIE OU DE BLESSURES,
NE PAS INSTALLER UN BÛCHES À GAZ ENAPPAREIL.
Use Solid wood, processed solid fuel fire logs (or other specified type) fuel only. / Utilisez du bois massif,
transformés solides bûches de combustible (ou un autre type spécifié) combustible seulement.
04 / 23 / 14
Do not use a fireplace insert or other products not specified for use with this product.
Ne utiliser pas un insert de cheminée ou d'autres produits non spécifiées pour l'utilisation avec ce produit.
SAMPLE
SAMPLE
T
ESTRESTR
TO A CHIMNO A CHIM
F STEEL LTD.F STEEL LTD.
OU DU SERVICE DESU DU SERVICE DES
STALLATION DANS VOTRETALLATION DANS VOTRE
EIL.
LE
MP
P
COMPONENTS REQUIREDCOMPONENTS REQUIRED
CHIMNEY REQUIREMECHIMNEY REQUIREM
TH THE FIREPLACE:FIREPLACE:
ION MANUALL
STRIPS
imney must be certified to one of the folmney must be certified to one of the f
ted States. Masonry chimney installatiod States. Masonry chimney installatio
639 for Ca639 for Ca
Air cooleAir coo
MINIMUM CHIMNEY HEIGHTMUM CHIMNEY HEIGHT
MAXIMUM CHIMNEY HEIGHTUM CHIMNEY HEIGHT
MAXIMUM OFFSETANGLEUM OFFSETA
C
EX
La cheminéeheminé
normes ULnormes U
inoxydabinoxydab
LIVRÉ AVEC LE FOYERLIVRÉ AVEC LE FOYE
MANUEL D'INSTRUCMANUEL D'INSTRUC
PARE-BRAI
S
E
SPARE-BRAISES
HA
SA
AVERTISSEMETISSEME
3RXUXQHXWLOLVDWUXQHXWLOLVD
les portes comportes co
ouvertes et couvertes et
fermées.fermées.
céramicéram
uniquniq
céc
WARNING:WARNIN
RUXVHZLWKGRRUVIXOO\XVHZLWKGRR
opened and doors fullyd and doors ful
c
losed. Replace ceramic
closed. Replace ceramic
g
lass onl
y
with ceramic
glass only with ceramic
g
lass obtained
f
rom the
glass obtained from the
dea
l
e
r
a
n
d
ce
rti
f
i
ed
fo
r
dealer and certified for
u
se with this appliance.
e with this appliance.
1RWIRUXVHLQD0RELOH1RWIRUX
Ho
m
e
.
Home.
M
LE
Nov.Nov.
ec/Déc.ec/Déc.
E
STED WITHSTED WITH
ISK OF FIREOF FIRE
ED GAS LOG SETED GAS LOG SET
ET APPAREIL N'AET APPAREIL N'A
À GAZ. POURÀ GAZ. POUR
IE OU DE BLESSURES,E OU DE BLESSUR
À GAZ EN APPAREIL.AZ EN APPAREIL.
fuel only. / Utilisez du bois massif,ez du bois massif,
spécifié) combustible seulement.seulement.
MP
fireplace insert or other products not spfireplace insert or other products not sp
ert de cheminée ou d'autres produits noert de cheminée ou d'autres produits
NOTE: The rating plate must
remain with the appliance at all
times. It must not be removed.

W415-1277 / 08.12.15
10
EN
3.0 INSTALLATION PLANNING
68.3B
!
WARNING
WEAR GLOVES AND SAFETY GLASSES FOR PROTECTION.
CAREFULLY FOLLOW THE INSTRUCTIONS FOR ASSEMBLY OF THE PIPE AND OTHER PARTS NEEDED TO INSTALL
THE APPLIANCE. FAILURE TO DO SO MAY RESULT IN A FIRE, ESPECIALLY IF COMBUSTIBLES ARE TOO CLOSE TO
THE APPLIANCE OR CHIMNEY AND AIR SPACES ARE BLOCKED, PREVENTING THE FREE MOVEMENT OF COOLING
AIR.
DO NOT DRAW OUTSIDE AIR FROM GARAGE SPACES. EXHAUST PRODUCTS OF GASOLINE ENGINES ARE
HAZARDOUS.
DO NOT INSTALL OUTSIDE AIR DUCTS SUCH THAT THE AIR MAY BE DRAWN FROM ATTIC SPACES, BASEMENTS
OR ABOVE THE ROOFING WHERE OTHER HEATING APPLIANCES OR FANS AND CHIMNEYS EXHAUST OR UTILIZE
AIR. THESE PRECAUTIONS WILL REDUCE THE POSSIBILITY OF APPLIANCE SMOKING OR AIR FLOW REVERSAL.
THE OUTSIDE AIR INLET MUST REMAIN CLEAR OF LEAVES, DEBRIS ICE AND/OR SNOW. IT MUST BE UNRE-
STRICTED WHILE APPLIANCE IS IN USE TO PREVENT ROOM AIR STARVATION WHICH CAN CAUSE SMOKE SPILL-
AGE AND AN INABILITY TO MAINTAIN A FIRE. SMOKE SPILLAGE CAN ALSO SET OFF SMOKE ALARMS.
NEGATIVE PRESSURE WITHIN YOUR HOME MAY INADVERTENTLY AFFECT YOUR APPLIANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE APPLIANCE MUST NOT BE INSTALLED
AGAINST VAPOUR BARRIERS OR EXPOSED INSULATION. LOCALIZED OVERHEATING COULD OCCUR AND A FIRE
COULD RESULT.
DO NOT USE MAKESHIFT COMPROMISES DURING INSTALLATION. DO NOT BLOCK OR RESTRICT AIR, GRILLE OR
LOUVRE OPENINGS. DO NOT ADD A HOOD.
KEEP HAND TOOLS IN GOOD CONDITION, SHARPEN CUTTING EDGES AND MAKE SURE TOOL HANDLES ARE
SECURE.
ALWAYS MAINTAIN THE MINIMUM AIR SPACE REQUIRED TO THE ENCLOSURE TO PREVENT FIRES.
THIS FIREPLACE IS NOT MEANT FOR ANY FIREPLACE INSERT OR OTHER PRODUCTS NOT
SPECIFIED FOR USE WITH THIS FIREPLACE.
USE ONLY NONCOMBUSTIBLE MATERIAL TO FINISH THE FACE OF THE FIREPLACE
ONLY USE MATERIAL LISTED IN THE REPLACEMENT PARTS SECTION.
KEEP FLAMMABLE LIQUIDS SUCH AS GASOLINE, KEROSENE LIGHTER FLUIDS OR OTHER SIMIALR LIQUIDS
AWAY FROM THE FIREPLACE.

W415-1277 / 08.12.15
11
EN
TABS
3.1 LOCATION AND CLEARANCES
IMPORTANT
This appliance, fully dressed, weighs 1400lbs (635kg). Ensure there is adequate floor support for the
appliance, chimney and facing material. Some material could weigh thousands of pounds.
DO NOT INSTALL INTO ANY AREA HAVING A HEIGHT LESS THAN 8 FEET (2.4M) (CEILING OF
ENCLOSURE TO APPLIANCE BOTTOM, EXCLUDING HEARTH HEIGHT).
We recommend that the appliance be secured to the floor in all cases.
Using the door opening as a datum, level the appliance by shimming underneath the appliance. Bend the tabs
down and secure the appliance to the floor.
3.1.1 VENTILATION OPENINGS
The appliance enclosure should be provided with sufficient air circulation to avoid a fire hazard. Install
ventilation grilles (minimum openings of 40 sq. inches (0.03 sq. meters)) at both floor and ceiling levels of the
enclosure. These grilles must not restrict the flow of heat by more than 25%. Do not install into any area having
a height less than 8 ft (2.4m) (ceiling of enclosure to appliance bottom, excluding hearth height). The location
of windows, doors and the traffic flow in the room where the stove is to be located should be considered. If
possible, you should choose a location where the chimney will pass through the house without cutting a floor
or roof joist.

W415-1277 / 08.12.15
12
EN Insulating the intake liner is recommended in colder
climates to prevent condensation from occurring.
The Napoleon Model NZ8000 takes outside air directly
into the appliance through the opening on the left side.
The fresh air inlet duct and hood must be installed lower
than the firebox. Secure and seal the intake liner to the
collar using 3 sheet metal screws, and high temperature
sealant.
3.2 OUTSIDE COMBUSTION AIR
The duct inlet must be located so they can not be blocked (i.e. snowdrifts). 12" (305mm) above grade is
recommended. Make a 4 ½" (114mm) inch hole to suit in an outside wall of the house. From outside, place the
fresh air hood into the hole, open side down. Seal with caulking and secure.

W415-1277 / 08.12.15
13
EN
An acceptable 70" (1778mm) x 20" (508mm) non-combustible (ie:
brick, stone or ceramic tile) hearth extension must be installed. Hearth
must extend 20" (508mm) in front of the faceplate when it is not
elevated (see local building codes). Hearth must extend a minimum of
12" (305mm) to both sides of the appliance door opening.
The hearth must extend a minimum 20" (508mm) in front of the appliance
although if raised a minimum of 6 1/2" (165mm) the 20" (508mm) may be
reduced to a minimum of 18" (0.45m).
The hearth must be a minimum of 1" (25mm) thick cement board (or
equivalent) plus ¼" (6.4mm) ceramic tile.
Ensure that the gap between the appliance and a non-combustible
hearth extension is sealed with sand/cement grout or covered with
an ember strip (or both) to prevent sparks and embers from falling
into this area.
Raised hearths must be constructed of non-combustible materials such
as cement blocks or bricks.
While the appliance can be installed directly on the floor, a non-combustible hearth extension is required in
front of the appliance, that must not be built higher than the bottom of the appliance faceplate. It may therefore
be advisable to build the appliance on a raised platform.
A raised hearth together with the appliance built on a raised platform is recommended for easier wood loading and
fire viewing.
EMBER STRIP
(See “HEARTH
EXAMPLES” Section)
HEARTH EXTENSIONS ARE TO BE INSTALLED ONLY AS DESCRIBED TO PREVENT HIGH
TEMPERATURES FROM OCCURRING ON CONCEALED COMBUSTIBLE MATERIALS. HEARTH
EMBER STRIPS PREVENT BURNING OR HOT PARTICLES FROM INADVERTENTLY FALLING
DIRECTLY ON COMBUSTIBLE SURFACES IN THE EVENT THE BUILDING SHOULD SETTLE AND
DISTURB THE ORIGINAL CONSTRUCTION.
3.3 FLOOR PROTECTION
3.3.1 EMBER STRIP AND HEARTH EXTENSIONS

W415-1277 / 08.12.15
14
EN
3.3.2 HEARTH EXTENSION
18" (457mm)
6 1/2"
(165mm)
70"
(1778mm)
70"
(1778mm)
20" (508mm)
12"
(305mm)
An acceptable 61½" (1562mm) x 20" (508mm) non-combustible
(ie: brick, stone or ceramic tile) hearth extension must be installed.
Hearth must extend 20" (508mm) in front of the faceplate when
it is not elevated (see local building codes). Hearth must extend
a minimum of 12" (305mm) to both sides of the appliance [70"
(1778mm)].
Hearth must be a minimum of 1" (25mm) thick cement board (or
equivalent) plus ¼" (6.4mm) ceramic tile.
Ensure that the gap between the appliance and a combustible
hearth extension is sealed with sand/cement grout or covered with
a metal strip (or both) to prevent sparks and embers from falling
into this area.
HEARTH EXTENSION
Elevated hearths must be constructed of noncombustible materials
such as cement blocks or bricks.
While the appliance can be installed directly on the floor, a non-
combustible hearth extension is required in front of the appliance,
that must not be built higher than the bottom of the appliance
faceplate. It may therefore be advisable to build the appliance on a raised platform.
Hearths raised minimum 6 ½" (165mm) must extend a minimum of 18" (457mm).
EMBER STRIP
SEE
HEARTH
EXAMPLES

W415-1277 / 08.12.15
15
EN
NON-COMBUSTIBLE MATERIALS
SUCH AS CEMENT
BLOCKS OR BRICKS
COMBUSTIBLE FRAMING
PLYWOOD INCREASE
HEADER HEIGHT
THIS DIMENSION
See “Framing” section
RAISED
APPLIANCE
COMBUSTIBLE FRAMING
NON-COMBUSTIBLE
MATERIALS SUCH
AS CEMENT BLOCKS
OR BRICKS
PLYWOOD INCREASE
HEADER HEIGHT
THIS DIMENSION
See “Framing” section
RAISED
HEARTH
RAISED
APPLIANCE
COMBUSTIBLE FLOOR
EMBER STRIP
EMBER STRIP
EMBER STRIP
EMBER STRIP
COMBUSTIBLE FLOOR
MIN. 1/4” (6.4mm)
TILE OR MARBLE 20” MIN.
(508mm)
MIN. 1” (25mm) CEMENT BOARD
6
1/2
”
(165mm)
18” MIN.
(457mm)
MIN. 1/4” (6.4mm)
TILE OR MARBLE
MIN. 1” (25mm)
CEMENT BOARD
MIN. 1/4” (6.4mm)
MARBLE OR STONE
18” MIN.
(457mm)
18” MIN.
(457mm)
3.3.3 HEARTH EXAMPLES
FLUSH HEARTH
RAISED HEARTH
RAISED APPLIANCE
RAISED HEARTH AND APPLIANCE
6”
(152mm)

W415-1277 / 08.12.15
16
EN
4.0 INSTALLATION
NOTE: All venting connections must be in compliance with the chimney manufacturers installation
instructions.
This appliance was tested to CAN/ULC S610 and UL 127 Factory Built Fireplace Standards. This appliance
has met the test criteria for Zero Clearance Installation to Combustible Surfaces and Certified to burn firewood
only.
A
ny 8” (203.2mm) diameter chimney listed to these standards may be installed. In accordance with these
standards, the appliance may also be connected to any chimney listed to CAN/ULC-S604 and CAN/ULC-S629
for Canada or UL-103HT for the United states.
Installation of all types of factory-built chimney systems is to
be in accordance with the chimney manufacturers installation
instructions. An appropriate chimney manufacturers anchor base
plate and anchor base plate gasket is required in order to initiate
their system. Use the high temperature gasket, supplied, to
seal between the anchor plate and the appliance top. Air cooled
chimney systems are not recommended in colder climates.
Complete installation instructions for Selkirk Ultra Temp Chimney
for Canada and Ultra Temp Platinum Chimney for USA, refer to:
www.selkirkinc.com/products/chimney.aspx
A
chimney venting the appliance shall not vent any other
appliance. The minimum overall chimney height from the top of the
appliance is 15ft (4.6m). The maximum overall chimney height from the top of the appliance is 34ft (10.4m).
Factory-built chimney systems for use in dwellings constructed for three or more families must be enclosed
above the room in which the appliance is located. This enclosure must have a fire resistance rating equal to or
greater than that of the floor or roof assembly through which they pass.
The chimney should not be built with an offset angle in excess of 45° in Canada and 30° in USA.
Ensure that minimum clearances are maintained.
Portions of the chimney that extend through accessible spaces must always be encased to avoid personal
contact with the chimney and thereby avoid damage to the chimney.
The chimney must be supported at a maximum of 20ft (6.1m) intervals [approx. 200 lbs/20 FT (90.7kg/6.1m)].
63.2A
ANCHOR PLATE
ANCHOR PLATE GASKET
APPLIANCE TOP
ANCHOR PLATE FOR A FACTORY
BUILT CHIMNEY
NEVER INSTALL A SINGLE WALL SLIP SECTION OR SMOKE PIPE IN A CHASE STRUCTURE.
THE HIGHER TEMPERATURE OF THIS SINGLE WALL PIPE MAY RADIATE SUFFICIENT HEAT TO
COMBUSTIBLE CHASE MATERIALS TO CAUSE A FIRE.
TO AVOID DANGER OF FIRE, ALL INSTRUCTIONS MUST BE STRICTLY FOLLOWED, INCLUDING
THE PROVISION OF AIR SPACE CLEARANCE BETWEEN CHIMNEY SYSTEM AND ENCLOSURE. TO
PROTECT AGAINST THE EFFECTS OF CORROSION ON THOSE PARTS EXPOSED TO THE WEATHER,
WE RECOMMEND THAT THE CHASE TOP BE PAINTED WITH A RUST-RESISTANT PAINT.
MAINTAIN A MINIMUM 2" (51mm) AIR CLEARANCE TO ALL PARTS OF THE CHIMNEY SYSTEM AT ALL
TIMES. FAILURE TO MAINTAIN THIS 2" (50.8mm) AIR CLEARANCE WILL CAUSE A STRUCTURE FIRE.
DETAILED INSTRUCTIONS FOR INSTALLATION OF THE CHASE TOP, STORM COLLAR AND
TERMINATION CAP ARE PACKAGED WITH THESE PARTS.
FIRESTOP SPACERS MUST BE USED WHENEVER THE CHIMNEY PENETRATES A CEILING/FLOOR
AREA.
THE CHIMNEY MUST BE SOUNDAND FREE OF CRACKS. CLEAN YOUR CHIMNEYAMINIMUM OF TWICE A
YEAR AND AS REQUIRED.
A raised hearth together with the appliance built on a raised platform is recommended for easier wood loading
and fire viewing.
4.1 CHIMNEY

W415-1277 / 08.12.15
17
EN
* The first flue offset closest to the top of the appliance must be a minimum distance of 12” (304.8mm)
from the top of the appliance.
1. Move the appliance into position. Try to center the exhaust flue of the appliance,
midpoint between two joists to prevent having to cut them. Use a plumb bob to
line up the centre.
2. Cut and frame an opening in the ceiling to provide a
minimum clearance of 2” (50.8mm) between the
outside of the chimney and any combustible material.
DO NOT FILL THIS SPACE WITH ANY TYPE OF
MATERIAL! Nail headers between the joists for extra
support. Firestop spacers must be placed on each
framed opening in any floor or ceiling that the chim-
ney passes through.
3. Hold a plumb bob from the underside of the roof
to determine where the opening in the roof should
be. Cut and frame the roof opening maintaining
proper 2” (50.8mm) clearances.
NOTE: 30° or 45° offsets may be installed back to
back.
63.5A
15 FT
(4.6m)
MINIMUM
34 FT
(10.4m)
MAXIMUM
RAIN CAP RAIN CAP
RAIN CAP
STORM COLLAR
ROOF FLASHING STORM COLLAR
ROOF FLASHING
STORM COLLAR
ROOF FLASHING
ATTIC INSULATION
SHIELD
ATTIC INSULATION
SHIELD ATTIC INSULATION
SHIELD
CEILING RADIATION
SHIELD
OFFSET
SUPPORT
OFFSET
SUPPORT
FIRESTOP FIRESTOP
12” (304.8mm)
MIN*
15 FT
(4.6m)
MINIMUM
34 FT
(10.4m)
MAXIMUM
12” (304.8mm)
MIN*
15 FT
(4.6m)
MINIMUM
34 FT
(10.4m)
MAXIMUM
2"
(50.8mm)
Min.
TypicalRoofJoist FramingTypical Joist Framing
2"
(50.8mm)
Min.
2" (50.8mm)
Min.
2"
(50.8mm)
Min.
STRAIGHT CHIMNEY SINGLE OFFSET
CHIMNEY DOUBLE OFFSET CHIMNEY
HEADERS
FIRESTOP SPACER -
UNDERSIDE OF JOIST
4.2 TYPICAL CHIMNEY INSTALLATION

W415-1277 / 08.12.15
18
EN
4.3 ADDING CHIMNEY SECTIONS
A
dd chimney sections, securely, to the required height.
If the chimney system is enclosed within the attic area, a rafter
radiation shield is required.
The chimney must extend at least 3ft (0.9m) above its point of
contact with the roof and at least 2ft (0.6m) higher than any wall,
roof or building within 10ft (3.1m).
If the chimney extends more than 5ft (1.5m) above the roof,
it must be secured using a roof brace or guide wires.
A
raincap must be installed to avoid internal damage and
corrosion.
Floor, Ceiling
Joist
LIVINGSPACE
Framed
Enclosure
2” (50.8mm)
clearance from
chimney to
combustible wall
Chimney Lengths
CeilingJoist
Chimney must be
totally enclosed
when passing
through living space
with a minimum 2”
(50.8mm) clearance
to combustibles.
3 ft.
(0.9m)
MIN.
2ft.
(0.6m)
59.2A
3 ft. (0.9m)
MIN. 2ft.
(0.6m)
10ft.
(3.1m)

W415-1277 / 08.12.15
19
EN
The first flue offset closest to the top of the unit must
be a minimum distance of 12" (304.8mm) from the top
of the appliance.
Attach an elbow to the chimney section, angled toward
the offset. Secure with 3 sheet metal screws.
To achieve the minimum offset, attach and secure a
second elbow. To achieve longer offsets, you may
install any available length of chimney pipe between
the elbows. Supports must be used on the first vertical
chimney section after a return elbow.
!
WARNING
CHIMNEY SECTIONS INSTALLED BETWEEN AN OFFSET AND RETURN REQUIRE STRUCTURAL
SUPPORT TO REDUCE OFF-CENTER LOADING AND TO PREVENT CHIMNEY SECTIONS FROM
SEPARATING AT THE CHIMNEY JOISTS.
THE CHIMNEY SHOULD NOT BE BUILT WITH AN OFFSET ANGLE IN EXCESS OF 45° IN CANADA AND
30° IN USA. DO NOT COMBINE OFFSET CHIMNEY COMPONENTS TO EXCEED THESE ANGLES.
Attic Insulation
Shield
StormCollar
Elbow
Elbow Support
Straps
Elbow
Roof
Flashing
Rain Cap
Elbow Support
Band
Roof Joist
Chimney Section
Floor , Ceiling Joist
If the offset length is
more than 36”
(914.4mm), an
intermediate support
must be employed.
To achieve longer
offsets, you may
install any available
length of chimney
pipe between the
elbows.The
intermediate support
must be used in
conjunction with an
offset support.
Firestop
63.6A
4.4 OFFSET CHIMNEY INSTALLATION

W415-1277 / 08.12.15
20
EN
4.5 INSTALLING FLASHING AND STORM COLLAR
88.1A
Remove the nails from the shingles above and to the sides of
the chimney. Place the flashing over the chimney pipe and slide
underneath the sides and upper edge of the shingles. Ensure that
the chimney pipe is properly centered within the flashing, giving
a 3/4” (19.1mm) margin all around. Fasten to the roof on the top
and sides. DO NOT NAIL through the lower portion of the flashing.
Make weather-tight by sealing with caulking. Where possible, cover
the sides and top edges of the flashing with roofing material. Apply
waterproof caulking, provided with the flashing, around the chimney,
1” (25.4mm) above the top of the flashing and push the storm collar
down into the caulking. Insert a rain cap onto the top of the last
chimney section.
RAIN CAP
CAULKING
STORM COLLAR
WEATHER
SEALANT
FLASHING
4.6 AIR COOLED CHIMNEY INSTALLATION
A. Install the base plate starter collar. Affix using the four
screws.
B. Install air housing to the appliance and connect to liner.
C. Follow the chimney manufacturer's instructions for
installing the chimney.
AIR HOUSING
Use only the DuraVent DuraPlus brand of air cooled chimney.
CHIMNEY COMPONENTS DuraPlus
12" (305mm) Chimney Section 8DP-12
24" (610mm) Chimney Section 8DP-24
36" (914mm) Chimney Section 8DP-36
15° Elbow 8DP-E15K
Flashing 8DP-FF or 8DP-F6
Chimney Cap 8DP-VC
Firestop / Radiation Shield 8DP-FRS
CHIMNEY COMPONENTS WOLF STEEL
Air Housing NZAC8KT
Base Plate 8DP-BP
NOTE: Only M&G DuraVent DuraPlus chimney
is allowed for use on this product.
AIR HOUSING
4" (102mm)
LINER
NOTE: Follow the chimney
manufacturer's instructions
for installing the chimney.