Napoleon GD25-N User manual

WS-415-099/03.16.99
LISTED DIRECT VENT MILLIVOLLISTED DIRECT VENT MILLIVOL
LISTED DIRECT VENT MILLIVOLLISTED DIRECT VENT MILLIVOL
LISTED DIRECT VENT MILLIVOLTT
TT
T
GAS-FIRED WALL FURNACEGAS-FIRED WALL FURNACE
GAS-FIRED WALL FURNACEGAS-FIRED WALL FURNACE
GAS-FIRED WALL FURNACE
INSTINST
INSTINST
INSTALLAALLA
ALLAALLA
ALLATION AND OPERATION AND OPERA
TION AND OPERATION AND OPERA
TION AND OPERATION INSTRUCTIONS FOR:TION INSTRUCTIONS FOR:
TION INSTRUCTIONS FOR:TION INSTRUCTIONS FOR:
TION INSTRUCTIONS FOR:
NATURAL GAS MODEL
GD25 - NGD25 - N
GD25 - NGD25 - N
GD25 - N
PROPANE GAS MODEL
GD25 - PGD25 - P
GD25 - PGD25 - P
GD25 - P
CERTIFIEDFORCANADA ANDUNITED STATESUSING ANSI/ AGA/ CGAMETHODS
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
CERTIFIEDUNDERCANADIAN AND AMERICANNATIONALSTANDARDS,
CSA2.33, ANDANSIZ21.88 RESPECTIVELYFOR VENTED GAS-FIREDSPACEHEATING APPLIANCES.
Wolf Steel Ltd., RR#1, 9 Napoleon Rd.,
Barrie, On., Canada L4M 4Y8 [phone]
• Immediately call your gas supplier from
a neighbour's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
WW
WW
WARNING:ARNING:
ARNING:ARNING:
ARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
FOR YOUR SAFETYFOR YOUR SAFETY
FOR YOUR SAFETYFOR YOUR SAFETY
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of
this or any other appliance.
WHAWHA
WHAWHA
WHATT
TT
TTT
TT
TO DO IF YOU SMELLO DO IF YOU SMELL
O DO IF YOU SMELLO DO IF YOU SMELL
O DO IF YOU SMELL GAS:GAS:
GAS:GAS:
GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
R-2000
Fax:[phone] Email:[email protected]
Web:www.napoleon.on.ca

2
WS-415-099/03.16.99
NAPOLEON gas fireplaces are manufactured under the strict Standard of the world recognized
ISO9002 Quality Assurance Certificate.
NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen
who take great pride in their work. The burner and valve assembly are leak and test-fired at a quality test
station.TThecompletefireplaceisthoroughlyinspectedbyaqualifiedtechnicianbeforepackagingtoensurethat
you, the customer, receives the quality product that you expect from NAPOLEON.
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTYNAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTYNAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
NAPOLEON GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY
The following materials and workmanship in your newThe following materials and workmanship in your new
The following materials and workmanship in your newThe following materials and workmanship in your new
The following materials and workmanship in your new NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON gas fireplace aregas fireplace are
gas fireplace aregas fireplace are
gas fireplace are
warranted against defects for as long as you own the fireplace. This covers: combustionwarranted against defects for as long as you own the fireplace. This covers: combustion
warranted against defects for as long as you own the fireplace. This covers: combustionwarranted against defects for as long as you own the fireplace. This covers: combustion
warranted against defects for as long as you own the fireplace. This covers: combustion
chamber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glasschamber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass
chamber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glasschamber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass
chamber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass
(thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled com-(thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled com-
(thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled com-(thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled com-
(thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled com-
ponents and aluminum extrusion trims.ponents and aluminum extrusion trims.
ponents and aluminum extrusion trims.ponents and aluminum extrusion trims.
ponents and aluminum extrusion trims.
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
thermal switch, switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are
covered andcovered and
covered andcovered and
covered and NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON will provide replacement parts free of charge during the first yearwill provide replacement parts free of charge during the first year
will provide replacement parts free of charge during the first yearwill provide replacement parts free of charge during the first year
will provide replacement parts free of charge during the first year
of the limited warranty.of the limited warranty.
of the limited warranty.of the limited warranty.
of the limited warranty.
Labour related to warranty repair is covered free of charge during the first year. RepairLabour related to warranty repair is covered free of charge during the first year. Repair
Labour related to warranty repair is covered free of charge during the first year. RepairLabour related to warranty repair is covered free of charge during the first year. Repair
Labour related to warranty repair is covered free of charge during the first year. Repair
work, however, requires the prior approval of an authorized company official. Labour costswork, however, requires the prior approval of an authorized company official. Labour costs
work, however, requires the prior approval of an authorized company official. Labour costswork, however, requires the prior approval of an authorized company official. Labour costs
work, however, requires the prior approval of an authorized company official. Labour costs
to the account ofto the account of
to the account ofto the account of
to the account of NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON are based on a predetermined rate schedule and any repairare based on a predetermined rate schedule and any repair
are based on a predetermined rate schedule and any repairare based on a predetermined rate schedule and any repair
are based on a predetermined rate schedule and any repair
work must be done through an authorizedwork must be done through an authorized
work must be done through an authorizedwork must be done through an authorized
work must be done through an authorized NAPOLEONNAPOLEON
NAPOLEONNAPOLEON
NAPOLEON dealer.dealer.
dealer.dealer.
dealer.
CONDITIONS AND LIMITCONDITIONS AND LIMIT
CONDITIONS AND LIMITCONDITIONS AND LIMIT
CONDITIONS AND LIMITAA
AA
ATIONSTIONS
TIONSTIONS
TIONS
NAPOLEONwarrants itsproducts againstmanufacturing defectsto the original purchaser only -- i.e.,the individualor legalentity (registeredcustomer) whosename appears on the
warrantyregistrationcard filed withNAPOLEON -- providedthatthepurchase was madethroughan authorized NAPOLEONdealer and issubjectto the followingconditionsandlimitations:
Thisfactory warrantyis nontransferableand may not be extended whatsoever byany ofour representatives.
Thegas fireplace mustbe installedbya licenced,authorized service technicianor contractor. Installationmust be donein accordance withthe installationinstructionsincluded withthe
productand alllocal and national building andfire codes.
Thislimited warrantydoes not cover damages causedby misuse,lack ofmaintenance, accident, alterations,abuse orneglect andparts installed from other manufacturerswill nullify
this warranty.
Thislimited warranty furtherdoesnot coveranyscratches, dents, corrosionordiscolouring causedbyexcessive heat, abrasiveand chemical cleanersnorchipping onporcelainenamel
parts,mechanical breakageof PHAZER™logs andembers, nor any venting componentsused inthe installationof thefireplace.
NAPOLEONwarrants itsstainlesssteelburners againstdefectsin workmanship andmaterialfor life, subjecttothe following conditions:During the first10yearsNAPOLEONwillreplace
or repair the defective parts at our option free of charge. From 10 years to life, NAPOLEON will provide replacement burners at 50% of the current retail price.
Inthe firstyear only,thiswarranty extendsto the repairor replacementof warranted partswhich are defectivein materialor workmanshipprovided that theproduct hasbeen operated
inaccordance withthe operationinstructions and under normal conditions.
Afterthe firstyear, withrespect to thisPresident's LimitedLifetime Warranty,NAPOLEON may, at itsdiscretion, fullydischarge all obligationswith respectto this warrantyby refunding
tothe originalwarranted purchaserthe wholesaleprice ofany warrantedbut defectivepart(s).
Afterthe first year, NAPOLEON willnot beresponsiblefor installation,labour or anyother costs orexpenses related tothe reinstallationofa warrantedpart, and suchexpenses are not
coveredby thiswarranty.
Notwithstandingany provisions containedin this President'sLimited Lifetime Warranty,NAPOLEON’S responsibilityunderthis warrantyisdefined asaboveand itshallnot in anyevent
extendto anyincidental,consequential orindirect damages.
Thiswarranty defines theobligationsand liability ofNAPOLEONwithrespect to theNAPOLEON gas fireplaceandany other warrantiesexpressed or impliedwithrespect to thisproduct,
itscomponents oraccessories areexcluded.
NAPOLEON neither assumes, norauthorizes anythird partyto assume, onits behalf,any other liabilitieswith respectto thesale of this product. NAPOLEONwill not be responsible
for:over-firing, downdrafts,spillage causedby environmental conditions such as rooftops, buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting
configurations,insufficient makeup air, or negative air pressures which may or maynot becaused bymechanical systemssuch asexhaust fans,furnaces, clothes dryers, etc.
Anydamages tofireplace, combustion chamber,heat exchanger,brass trimor other component dueto water,weather damage, longperiods ofdampness, condensation, damaging
chemicals or cleaners will not be the responsibility of NAPOLEON.
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. The warranty registration
cardmust bereturned withinfourteen daysto registerthe warranty.
NAPOLEONreserves theright tohave itsrepresentative inspectany productor partthereof priorto honouringany warrantyclaim.
ALLSPECIFICATIONS AND DESIGNS ARE SUBJECTTO CHANGE WITHOUT PRIOR NOTICEDUE TOON-GOING PRODUCTIMPROVEMENTS. NAPOLEON®IS A REGISTERED
TRADEMARK OF WOLF STEEL LTD. PATENTS U.S. 5.303.693.801 - CAN. 2.073.411, 2.082.915. © WOLF STEEL LTD.

3
WS-415-099/03.16.99
PLEASE RETPLEASE RET
PLEASE RETPLEASE RET
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCEAIN THIS MANUAL FOR FUTURE REFERENCE
AIN THIS MANUAL FOR FUTURE REFERENCEAIN THIS MANUAL FOR FUTURE REFERENCE
AIN THIS MANUAL FOR FUTURE REFERENCE
TT
TT
TABLEABLE
ABLEABLE
ABLE ofof
ofof
of CONTENTSCONTENTS
CONTENTSCONTENTS
CONTENTS
PG 2-4PG 2-4
PG 2-4PG 2-4
PG 2-4 INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
Warranty
General Instructions
General Information
Care of Glass & Plated Parts
5-65-6
5-65-6
5-6 VENTINGVENTING
VENTINGVENTING
VENTING
Venting Lengths
Air Terminal Locations
7-137-13
7-137-13
7-13 INSTINST
INSTINST
INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
Wall & Ceiling Protection
Using Flexible Vent Components
Using Rigid Vent Components
Gas Installation
Mobile Home Installation
Framing
14-1514-15
14-1514-15
14-15FINISHINGFINISHING
FINISHINGFINISHING
FINISHING
Log Placement
Optional Glowing Ember Installation
Door Removal & Installation
PGPG
PGPG
PG 1616
1616
16 OPTIONAL BLOWER INSTOPTIONAL BLOWER INST
OPTIONAL BLOWER INSTOPTIONAL BLOWER INST
OPTIONAL BLOWER INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1717
1717
17 OPTIONAL FOPTIONAL F
OPTIONAL FOPTIONAL F
OPTIONAL FAN & THERMOSTAN & THERMOST
AN & THERMOSTAN & THERMOST
AN & THERMOSTAA
AA
ATIC SENSORTIC SENSOR
TIC SENSORTIC SENSOR
TIC SENSOR
1818
1818
18 OPERAOPERA
OPERAOPERA
OPERATION / MAINTENANCETION / MAINTENANCE
TION / MAINTENANCETION / MAINTENANCE
TION / MAINTENANCE
Operating Instructions
Maintenance
1919
1919
19 ADJUSTMENTSADJUSTMENTS
ADJUSTMENTSADJUSTMENTS
ADJUSTMENTS
Pilot Burner Adjustment
Venturi Adjustment
20-2120-21
20-2120-21
20-21 REPLACEMENTSREPLACEMENTS
REPLACEMENTSREPLACEMENTS
REPLACEMENTS
Ordering Replacement Parts
Replacement Parts
Accessories
Vent Kits
Terminal Kits
22-2322-23
22-2322-23
22-23 TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
GENERAL INSTRUCTIONS
THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local
codes. In absence of local codes, install to the current CAN/CGA -B149 Installation Code in Canada or to the National
Fuel Gas Code, ANSI Z223.1, and NFPA 54 in the United States. Mobile home installation must conform with local codes
or in the absence of local codes, install to the current standard for gas equipped mobile housing CAN/CSA ZA240 MH
Series in Canada or ANSI Z223.1 and NFPA 54 in the United States.
Purge all gas lines with the glass door of the fireplace removed. Assure that a continuous gas flow
is at the burner before installing the door.
Under extreme vent configurations, allow several minutes (5-15) for the flame to stabilize after
ignition.
Eight (8") inches is the minimum bend radius allowed for the 7" diameter flexible air liner.
This fireplace may be installed in an aftermarket permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This fireplace is only for use with the type of gas indicated on the rating plate. This fireplace is not
convertible for use with other gases, unless a certified kit is used.
The fireplace and its individual shutoff valve must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The fireplace must be isolated from the
gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).
When the fireplace is installed directly on carpeting, vinyl tile or other combustible material other than wood flooring, the
fireplace shall be installed on a metal or wood panel extending the full width and depth.
The optional fan or blower is supplied with a cord. If installed, the junction box must be electrically connected and
grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN
ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1996 NATIONAL ELECTRICAL CODE in the United States.

4
WS-415-099/03.16.99
WARNINGWARNING
WARNINGWARNING
WARNING
••
••
• Donotburnwoodorothermaterialsinthisfireplace.
• Adultsandespeciallychildrenshouldbealertedtothehazardsofhighsurfacetemperaturesandshouldstayaway
toavoid burns or clothing ignition.Superviseyoungchildren when they areinthesame room as the fireplace.
• Duetohightemperatures,thefireplaceshouldbelocatedoutoftrafficandawayfromfurnitureanddraperies.
• Clothingorotherflammablematerialshouldnotbeplacedonornearthefireplace.
• Anysafetyscreenorguardremovedforservicingmustbereplacedpriorto operatingthefireplace.
• Itisimperativethatthecontrolcompartments,burnersandcirculatingbloweranditspassagewayinthefireplace
and venting system are kept clean. The fireplace and its venting system should be inspected before use and at
least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from
carpeting, bedding material, etc. The fireplace area must be kept clear and free from combustible materials,
gasolineandotherflammablevapoursandliquids.
• Underno circumstancesshouldthis fireplacebe modified.
• Thisfireplace must notbeconnected toachimney flue pipeservinga separatesolidfuel burning appliance.
• Donotusethisfireplaceifanyparthasbeenunderwater.Immediatelycallaqualifiedservicetechniciantoinspect
thefireplaceandtoreplace anypartofthecontrolsystemand anygas controlwhichhasbeenunderwater.
• Donotoperatethefireplacewiththeglassdoorremoved,crackedorbroken.Replacementoftheglassshouldbe
done by a licensed or qualified service person. Use only with a glass door certified with the fireplace.
• Donotstrike orslamshutthefireplaceglassdoor.
GENERAL INFORMAGENERAL INFORMA
GENERAL INFORMAGENERAL INFORMA
GENERAL INFORMATIONTION
TIONTION
TION
FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUALITY!
Maximum input is 25,000 BTU/hr for natural gas and propane. When the fireplace is installed at elevations above 4,500ft,
and in the absense of specific recommendations from the local authority having jurisdiction, the certified high altitude
input rating shall be reduced at the rate of 4% for each additional 1,000ft. Maximum output for natural gas is 19,500 BTU/
hr at an efficiency of 78% with the fan on; and 20,250 BTU/hr for propane at an efficiency of 81% with the fan on. Maximum
A.F.U.E. (annual fuel utilization efficiency) rating is 69% for natural gas and 70% for propane. Minimum A.F.U.E. rating is
63% for natural gas and propane.
Minimum inlet gas supply pressure is 4.5 inches water column for natural gas and 11 inches water column for propane.
Maximum inlet gas pressure is 7 inches water column for natural gas and 13 inches water column for propane. Manifold
pressure under flow conditions is 3.5 inches water column for natural gas and 10 inches water column for propane.
This fireplace is approved for bathroom, bedroom and bed-sitting room installations and is suitable for mobile home
installation. The natural gas model can only be installed in a mobile home that is permanently positioned on its site and
fueled with natural gas.
NOEXTERNALELECTRICITY (110 VOLTS OR 24 VOLTS)ISREQUIREDFOR THE GAS SYSTEMOPERATION. Expansion
/ contraction nosies during heating up and cooling down cycles are normal and are to be expected.
PROVIDEADEQUATEVENTILATIONANDCOMBUSTIONAIR.PROVIDEADEQUATEACCESSIBILITYCLEARANCEFORSERVIC-
ING AND OPERATING THE FIREPLACE. NEVER OBSTRUCT THE FRONT OPENING OF THE FIREPLACE.
CARE OF GLASS, AND PLACARE OF GLASS, AND PLA
CARE OF GLASS, AND PLACARE OF GLASS, AND PLA
CARE OF GLASS, AND PLATED PTED P
TED PTED P
TED PARAR
ARAR
ARTSTS
TSTS
TS
Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean dry cloth. The glass is 3/16" ceramic glass
available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the first
10 hours of operation with a recommended gas fireplace glass cleaner. Thereafter clean as required. DO NOT CLEAN
GLASS WHEN HOT! If the glass is not kept clean permanent discolouration and / or blemishes may result.
FIGURE 1

5
WS-415-099/03.16.99
VENTING
VENTING LENGTHS AND AIR TERMINAL LOCAVENTING LENGTHS AND AIR TERMINAL LOCA
VENTING LENGTHS AND AIR TERMINAL LOCAVENTING LENGTHS AND AIR TERMINAL LOCA
VENTING LENGTHS AND AIR TERMINAL LOCATIONSTIONS
TIONSTIONS
TIONS
Use only Napoleon or Simpson Dura-Vent Model DV-GS venting components. Minimum and maximum vent lengths, for
both horizontal and vertical installations, and air terminal locations for either system are set out in this manual and must
be adhered to. For Simpson Dura-Vent, follow the installation procedure provided with the venting components.
NOTE:BothWolf Steeland Simpson Dura-Vent requirethe 4 inchandthe7inch diameter ventjointstobesealed.
Use the high temperature sealant provided.
When using Napoleon venting components, use only the following vent kits: WALL TERMINAL KIT GD222, or 1/12 TO 7/
12PITCH ROOF TERMINAL KITGD110, 8/12 TO12/12 ROOF TERMINAL KIT GD111,FLAT ROOFTERMINAL KIT GD112
or PERISCOPE KIT GD201 (for wall penetration below grade) in conjunction with the various terminations, use either the
5 foot vent kit GD220 or the 10 foot vent kit GD330.
These vent kits allow for either horizontal or vertical venting of the fireplace. FIGURES 2, 3, & 4. The maximum number of
4" flexible connections is two horizontally or three vertically (excluding the fireplace and the air terminal connections).
For optimum flame appearance and fireplace performance, keep the vent length and number of elbows to a minimum.
The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is
unobstructed and undamaged.
Horizontal runs can have a 0 inch rise per foot using Simpson Dura-Vent , Napoleon rigid or flexible venting
components when venting as illustrated in Figure 2a - c.
Provide a means for visually checking the vent connection to the fireplace after the fireplace is installed.
Donotallowtheinside liner to bunch uponhorizontalor vertical runsand elbows.Keepit pulled tight. A 1-1/4" air
gap between the inner and outer liner all around is required for safe operation.
Use a firestop when penetrating interior walls, floor or ceiling.
Vent lengthsthatpassthrough unheatedspaces(attics, garages,crawlspaces)should beinsulatedwith insulation
and wrapped in a protective sleeve to minimize consensation.
Minimum clearance to combustible construction from fireplace to vent surfaces:
sides, back, bottom, and top 0 inches
vent pipe 1 inch
recessed depth 13-3/4 inches
When venting, the horizontal run must be kept to a minimum of 8 inches or a maximum of 24
inches.If a greater horizontal run is required, the fireplace must have a minimum vertical rise
immediately off the fireplace of 24 inches. With this configuration, the horizontal run can be
between a minimum of 13 inches and a maximum of 96 inches. FIGURE 2FIGURE 2
FIGURE 2FIGURE 2
FIGURE 2a-ba-b
a-ba-b
a-b..
..
. When terminat-
ingvertically,theverticalriseisaminimum36inchesandamaximum40feetfromthecentreof
the fireplace flue outlet. FIGURE 3.FIGURE 3.
FIGURE 3.FIGURE 3.
FIGURE 3.
For safe and proper operation of the fireplace, follow the venting instructions exactly.
Onall horizontal runs, when determining air terminal locations, checkfor appropriate rise per
footrequirements.
A terminal shall not terminate directly above a sidewalk or paved driveway which is located
betweeen two single family dwellings and serves both dwellings. Local codes or regulations
may require different clearances.
Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it
pulled tight. A 1¼" air gap all around between the inner liner and outer liner is required for
safe operation. Use a firestop when penetrating interior walls, floor or ceiling.
FIGURE3
FIGURES 2a - d

6
WS-415-099/03.16.99
FIGURE4
AIRAIR
AIRAIR
AIR TERMINTERMIN
TERMINTERMIN
TERMINAL INSTAL INST
AL INSTAL INST
AL INSTALLAALLA
ALLAALLA
ALLATIONS:TIONS:
TIONS:TIONS:
TIONS:
**
**
* Recommended to prevent condensation on windows and thermal breakage
****
****
** It is recommended to use a heat shield and to maximize the distance to vinyl clad soffits.
******
******
*** The periscope GD-201 requires a minimum 18 inches clearance from an inside corner.
********
********
**** This is a recommended distance. For additional requirements check local codes.
††
††
† Three feet above if within 10 feet horizontally.
‡‡
‡‡
‡ A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family
dwellings and serves both dwellings.
††††
††††
†† Permitted only if the veranda, porch, deck or balcony is fully open on a minimum of two sides beneath the floor.
†*†*
†*†*
†* Recommenced to prevent recirculation of exhaust products. For additional requirements check local codes.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
12INCHES
9INCHES
12 INCHES*
18 INCHES**
12 INCHES**
0INCHES
2 INCHES***
0POUCES***
3FEET****
3FEET****
9INCHES
3FEET†
7FEET****
12INCHES****
16INCHES
2FEET†*
Clearanceabove grade, veranda porch, deckorbalcony.
Clearanceto windows or doors that open.
Clearancetopermanentlyclosedwindows.
Verticalclearancetoventilatedsoffitlocatedabovetheterminalwithin
a horizontal distance of 2 feet from the centerline of the terminal.
Clearanceto unventilated soffit.
Clearanceto an outside corner wall.
Clearance to an inside non-combustible corner wall or protruding
non-combustible obstructions (chimney, etc.).
Clearance to an inside combustible corner wall or protruding com-
bustible obstructions ( vent chase, etc.).
Clearancetoeachsideofthecenterlineextendedabovethemeter
/ regulator assembly.
Clearancetoaserviceregulatorventoutlet.
Clearance to a non-mechanical air supply inlet to the building or a
combustion air inlet to any other appliance.
Clearance to a mechanical air supply inlet.
Clearance above a paved sidewalk or paved driveway located on
public property unless fitted with a heat shield kit GD-301.
Clearanceunderaveranda,porch,deckorbalcony.
Clearanceabove the roof.
Clearancefroman adjacent wall including neighbouring buildings.
CANADIAN U.S.A.
12INCHES
12INCHES
12 INCHES*
18 INCHES**
12 INCHES**
0INCHES
0 INCHES***
0POUCES***
3FEET
6FEET
12INCHES
6FEET
7FEET‡
12INCHES††
16INCHES
2FEET†*
INSTALLATIONS

7
WS-415-099/03.16.99
INSTALLATION
WALL AND CEILING PROTECTION
FORSAFEANDPROPEROPERATIONOFTHEFIREPLACE,FOLLOWTHEVENTINGINSTRUCTIONSEXACTLY.
HORIZONTAL INSTALLATION: This application occurs when venting through
an exterior wall. FIGURES 2a-c. Having determined the air terminal location, cut and
frame a hole in an exterior wall with a minimum square or round opening of 9½".
(As an alternative to framing, a vent pipe shield may be installed, ensuring a 1"
clearance to combustibles. See Figure 6.)
1. Mark and cut the vent pipe shield to the determined depth of the combustible
wall. Apply a bead of caulking (not supplied) to the framework or to the shield plate
(in the case of a finished wall) and
secure the shield through the open-
ing to the interior wall. The final lo-
cation of the vent pipe shield should
maintain the required clearance to
the 7" vent pipe / liner. Do not fill this cavity with any type of material. Apply
a bead of caulking all around and place a firestop spacer over the vent
shield to restrict cold air from being drawn into the room or around the
fireplace. Ensure that both spacer and shield maintain the required clear-
ance to combustibles. Once the vent pipe / liner is installed in its final
position, apply sealant between the pipe / liner and the firestop spacer.
VERTICAL INSTALLATION: Thisapplicationoccurs when venting through
a roof. FIGURE 3. Installation kits for
various roof pitches are available from your Napoleon dealer. See Accessories to
order the specific kit required.
1. Determine the air terminal location, cut and frame 9½ inch openings in the
ceiling and the roof to provide the minimum 1 inch clearance between the fireplace
pipe / liner and any combustible material. Try to center the exhaust pipe location
midway between two joist to prevent having to cut them. Use a plumb bob to line up
the center of the openings.
DONOT FILL THISSPACE WITH ANYTYPE OF MATERIAL.
A vent pipe shield will prevent any materials such as insulation, from filling up the 1"
air space around the pipe. FIGURE 9. Nail headers between the joist for extra sup-
port.
2. Apply a bead of caulking (not supplied) to the framework or to the Wolf Steel vent pipe shield plate or equivalent (in
the case of a finished ceiling), and secure over the opening in the ceiling. FIGURE 8. A firestop must be placed on the
bottom of each framed opening in a roof or ceiling that the venting system passes
through. FIGURE 7. Apply a bead of caulking all around and place a firestop spacer
over the vent shield to restrict cold air from being drawn into the room or around the
fireplace. Ensure that both spacer and shield maintain the required clearance to
combustibles. Once the vent pipe / liner is installed in its final position, apply
sealant between the pipe / liner and the firestop spacer.
3. In the attic, after the pipe / liner has been installed, slide the vent pipe collar
down to cover up the open end of the shield and tighten. This will prevent any
materials, such as insulation, from filling up the 1"
air space around the pipe.
FIGURE6
OR
FIGURE7
FIGURE8
FIGURE9
VENT PIPE
SHIELD
VENT
PIPE
COLLAR
FIGURE5

8
WS-415-099/03.16.99
FIGURE11
USING FLEXIBLE VENT COMPONENTS
FORSAFEANDPROPEROPERATIONOFTHEFIREPLACE,FOLLOWTHEVENTINGINSTRUCTIONSEXACTLY.
HORIZONTHORIZONT
HORIZONTHORIZONT
HORIZONTAL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Stretch the 4" diameter aluminum flexible liner to the required length
taking into account the additional length needed for the finished wall
surface. Apply a heavy bead of the high temperature sealant, supplied
with the unit, to the inside of the 4" liner approximately 1" from the end.
Slip the liner a minimum of 2" over the fireplace vent collar and secure
with 3 #8 screws.
2. Using the 7" diameter flexible aluminum liner, apply sealant, slide
a minimum of 2 " over the fireplace combustion air collar and secure with
3 #8 screws.
3. Insert the liners through the firestop. Position and secure the fireplace using
the nailing tabs (2 per side) and/or secure to the floor using screws inserted through
the two ¼" diameter holes in the front left and right corners of the base. The liners should
be flush with the exterior wall. The air teminal plate may be recessed up to a maximum of 3/
4" into the exterior wall or siding.
4. From outside, apply a bead of the high temperature sealant to the inside of both liners, approxi-
mately 1" from the end of each liner.
5. Holding the air terminal (lettering in an upright, readable position), insert into both liners with a twisting motion to
ensure that both the terminal sleeves engage into the liners / sealant. Secure the terminal to the exterior wall and make
weather tight by sealing with caulking (not supplied).
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTAL AND CORNER AIR TERMINAL INSTAL AND CORNER AIR TERMINAL INST
AL AND CORNER AIR TERMINAL INSTAL AND CORNER AIR TERMINAL INST
AL AND CORNER AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
A 45° corner installation must have 6 inch minimum rise between the fireplace combustion air collar and the air
terminal. FIGURE 2d. In this case, vent lengths must be kept to a maximum of 36". For longer vent lengths, a minimum
vertical rise of 24" is required. FIGURE 2c. Use the GD220 vent kit and couplers for this application.
1. Follow the instructions for "Horizontal Air Terminal Installations"., items 1 through 5.
Spacers are attached to the 4" inner flex liner at predetermined intervals to maintain a 1-1/4" air gap to the 7" outer
liner. These spacers must not be removed.
2. The vent system must be supported approximately every 3
feet for both vertical and horizontal runs. Use Napoleon support
ring assemblies, GA-GD-010.370 or equivalent noncombustible
strapping to maintain the minimum 1" clearance to combustibles.
FIGURE10

9
WS-415-099/03.16.99
FIGURE13
VERVER
VERVER
VERTICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Fasten the roof support to the roof using the screws
provided. The roof support is optional. In this case the vent-
ing is to be adequately supported using either an alternate
method suitable to the authority having jurisdiction or the
optional roof support.
2. Stretch the 4" diameter aluminum flexible liner to the
required length. Slip the liner a minimum of 2" over the
inner sleeve of the air terminal and secure with 3 #8 screws.
Seal using a heavy bead of the high temperature sealant.
3. Repeat using 7" diameter aluminum flexible liner. FIGURE 12.
4. Thread the air terminal pipe assembly down through the roof. The air terminal must be
located vertically and plumb. Attach the air terminal assembly to the roof support, ensuring that
a minimum 16" of air terminal will penetrate the roof when fastened.
DONOT CLAMP THEFLEXIBLEALUMINUM LINER.
5. Remove nails from the shingles, above and to the sides of the chimney. Place
the flashing over the air terminal and slide it underneath the sides and upper edge
of the shingles. Ensure that the air terminal is properly centered within the flashing,
giving a 3/4" margin all around. Fasten to the roof. Do not nail through the lower
portion of the flashing. Make weather-tight by sealing with caulking. Where pos-
sible, cover the sides and top edges of the flashing with roofing material.
6. Apply a heavy bead of weatherproof caulking 2 inches above the flashing. Slide
the storm collar around the air terminal and down to the caulking. Tighten to ensure
that a weather-tight seal between the air terminal and the collar is achieved. Attach
the other storm collar centered between the air intake and the air exhaust slots onto
the air terminal. Tighten securely. FIGURE 13. Attach the vertical rain cap.
Spacers are attached to the 4" inner flex liner at predetermined intervals to maintain a 1-1/4" air gap to the 7" outer
liner. These spacers must not be removed.
7. If more liner needs to be used to reach the fireplace, follow the same procedure as found in EXTENDED HORIZON-
TAL AND CORNER AIR TERMINAL INSTALLATION. The vent system must be supported approximately every 3 feet for
both vertical and horizontal runs. Use Wolf Steel support ring assembly GA-GD-010.370 or equivalent noncombustible
strapping to maintain a clearance to combustibles of 1".
FIGURE14
FIGURE12

10
WS-415-099/03.16.99
INSTALLATION
USING RIGID VENT COMPONENTS
FORSAFE AND PROPER OPERATIONOF THE FIREPLACE,FOLLOW THE VENTING INSTRUCTIONS EXACTLY.
HORIZONTAL RUNS MAY HAVE A ZERO INCH RISE PER FOOT
The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon vent
spacers WS-615-33 or equivalent every 3 feet and either side of each elbow to maintain the minimum 1¼" clearance
between the outer and inner vent pipes. Use Napoleon support ring assembly GA-GD-010.370 or equivalent noncom-
bustible strapping to maintain the minimum 1" clearance to combustibles for both vertical and horizontal runs.
HORIZONTHORIZONT
HORIZONTHORIZONT
HORIZONTAL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTAL AIR TERMINAL INST
AL AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Move the fireplace into position. Measure the vent length
required between terminal and fireplace taking into account the
additional length needed for the finished wall surface and any
1¼" overlaps between venting components.
2. Apply high temperature sealant to the outer edge of the 4"
inner collar of the fireplace. Attach the first vent component and
secure using 3 self tapping screws. Repeat using 7" piping.
3. Holding the air terminal (lettering in an upright, readable
position), insert into both vent pipes with a twisting motion to
ensure that both the terminal sleeves engage into the vent pipes
and the sealant. Secure the terminal to the exterior wall and
make weather tight by sealing with caulking (not supplied). The
air terminal mounting plate must not be recessed into the exterior wall or siding.
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTEXTENDED HORIZONT
EXTENDED HORIZONTAL AND CORNER AIR TERMINAL INSTAL AND CORNER AIR TERMINAL INST
AL AND CORNER AIR TERMINAL INSTAL AND CORNER AIR TERMINAL INST
AL AND CORNER AIR TERMINAL INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
A 45° corner installation can have 6 inch minimum rise between the fireplace
combustion air collar and the air terminal. In this case, vent lengths must be
kept to a maximum of 36". For longer vent lengths, a minimum vertical rise of 24"
is required. FIGURE 2c.
1. Follow the instructions for "Horizontal Air Terminal Installations", items 1 to
2.2. Continue adding components alternating inner and outer venting. Ensure
that all 4" venting and elbows have sufficient vent spacers attached and each
component is securely fastened to the one prior. Attach the 4" telescopic sleeve
to the vent run. Repeat using a 7" telescopic sleeve. Secure and seal as before.
To facilitate completion, attach 4" and 7" couplers to the air terminal.
3.Install the air terminal. See item 3 above. Extend the 4" telescopic sleeve;
connect to the air terminal assembly. Fasten with self tapping screws and seal.
Repeat using the 7" telescopic sleeve.
Elbows and rigid 36" lengths are manufactured with the 4" components permanently fixed within the 7" compo-
nents. apply high temperature sealant to both collars and install the assembly as a single unit securing the outer
7" piece with three screws.
FIGURE16
FIGURE15
TELESCOPIC SLEEVE
VENTING
AIR TERMINAL
20"
COUPLER

11
WS-415-099/03.16.99
VERVER
VERVER
VERTICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTTICAL VENTING INST
TICAL VENTING INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
1. Move the fireplace into position.
2. Fasten the roof support to the roof using the screws provided. The roof
support is optional. In this case the venting is to be adequately supported using
either an alternate method suitable to the authority having jurisdiction or the
optional roof support.
3. Apply high temperature sealant to the outer edge of the inner sleeve of the
air terminal. Slip a 4" diameter coupler a minimum of 2" over the sleeve and
secure using 3 screws.
4.Apply high temperature sealant to the outer edge of the of the outside sleeve
of the air terminal. Slip a 7" diameter coupler over the sleeve and secure as
before. Trim the 7" coupler even with the 4" coupler end.
5.Thread the air terminal pipe assembly down through the roof support and attach, ensuring that a minimum 16" of
air terminal will penetrate the roof when fastened. If the attic space is tight, we recommend threading the Wolf Steel
vent pipe collar or equivalent loosely onto the air terminal assembly as it is passed through
the attic. FIGURE 19. The air terminal must be located vertically and plumb.
6.Remove nails from the shingles, above and to the sides of the chimney. Place the flashing
over the air terminal and slide it underneath the sides and upper edge of the shingles. Ensure
that the air terminal is properly centered within the flashing, giving a 3/4" margin all around.
Fasten to the roof. Do NOT nail through the lower portion of the
flashing. Make weather-tight by sealing with caulking. Where pos-
sible, cover the sides and top edges of the flashing with roofing
material.
7. Apply a heavy bead of waterproof caulking 2 inches above the
flashing. Slide the storm collar around the air terminal and down to
the caulking. Tighten to ensure that a weather-tight seal between
the air terminal and the collar is achieved. Attach the other storm
collar centered between the air intake and air exhaust slots onto
the air terminal. Tighten securely. Attach the rain cap.
8. Continue adding rigid venting sections, seal-
ing and securing as above. Attach a 4" collapsed telescopic pipe to the last
section of rigid piping. Secure with screws and seal. Repeat using a 7" tele-
scopic pipe.
9. Run a bead of high temperature sealant around the outside of the 4" elbow.
Pull the adjustable pipe a minimum 2" onto the elbow. Secure with 3 screws.
Repeat with the 7" telescopic pipe.
10. In the attic, slide the vent pipe collar down to cover up the open end of the
shield and tighten. This will prevent any materials, such as insulation, from
filling up the 1" air space around the pipe.
FIGURE17
FIGURE20
FIGURE19
VENT PIPE
SHIELD
VENT
PIPE
COLLAR
FIGURE18

12
WS-415-099/03.16.99
MOBILE HOME INSTMOBILE HOME INST
MOBILE HOME INSTMOBILE HOME INST
MOBILE HOME INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
In Canada, mobile home installation may be vented horizontally or vertically. In the United States, it may only be installed
vertically. See "Vertical Venting" or "Horizontal Air Terminal Installation" for installation. To vent the fireplace vertically, a
vent length of 3 feet minimum to 10 feet maximum may be used only.
The fireplace is equipped with two 1/4" diameter holes located in the front left and right corners of the base. For mobile
home installations, the fireplace must be fastened in place. Use #10 screws, inserted through the holes in the base to
secure. It is recommended that the fireplace be secured in all installations.
GAS INSTGAS INST
GAS INSTGAS INST
GAS INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
Proceed once the vent installation is complete.
1. Move the fireplace into position.
2. Route a 3/8" N.P.T. black iron gas line, 1/2" type-L copper tubing or equivalent to the fireplace.
3. For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient
location. Route 2-strand (solid core) millivolt wire through the electrical hole located at the bottom left side of the unit.
The recommended maximum lead length depends on wire size: WIRESIZE MAX.LENGTH
14gauge 100 feet
16gauge 60 feet
18gauge 40 feet
Attach the two leads to terminals
1 and 3 located on the gas valve.
FIGURE21.
4. Install rigid black pipe, 1/2" type-L copper tubing or, if local codes permit, a 3/8" flex connector and shutoff valve to
the gas line and the fireplace gas valve. Seal and tighten securely. An adapter fitting is required between the gas valve
and the copper tubing or flex connector.
DONOT KINKFLEXCONNECTOR. FIGURE22.
5. Check for gas leaks by brushing on a soap and water solution.
DONOT USE OPENFLAME. FIGURE22
PURGEALL GAS LINESWITHTHE GLASSDOOROF THEFIREPLACEREMOVED. ASSURETHAT ACONTINUOUS
GASFLOW ISATTHE BURNERBEFORERE-INSTALLINGTHEDOOR.
Always turn the pilot and the fuel supply at the source off prior to moving the mobile home.
After moving the mobile home and prior to lighting the fireplace, ensure that the logs are positioned correctly.
FIGURE21 DO NOT CONNECT EITHER THE
WALL SWITCH, THERMOSTAT OR
GAS VALVE TO ELECTRICITY (110
VOLTS).
P
I
P
I
3
1
2
L
O
T
N
O
L
O
T
H
I
L
O
F
F
O

13
WS-415-099/03.16.99
FRAMINGFRAMING
FRAMINGFRAMING
FRAMING
It is best to frame your fireplace after it is positioned and the vent system is installed. Use 2x4's and frame to local
building codes. FIGURE 23-26.
To install the fireplace face flush with the finished wall, position the framework to accomodate the thickness of the
finished wall. For corner installation, allow a minimum rise of 6 inches between the fireplace and the air terminal.
FIGURE 2d. Pull out the four nailing tabs, attached on either side of the fireplace and secure to the 2x4 framing to facilitate
drywall installation.
Combustible materials must be installed flush with the front of the fireplace but must not cover any of the black face-area
of the fireplace. Non-combustible material (brick, stone or ceramic tile) may protrude.
It is not necessary to install a hearth extension with this fireplace system. Objects placed in front of the fireplace should
be kept a minimum of 24" away from the front face.
Mantle clearance can vary according to the mantle depth. FIGURE 27. Use the graph to help evaluate the clearance
needed.
M
A
N
T
L
E
H
E
I
G
H
T
MANTLE WIDTH
FIGURE23
FIGURE27
OUTSIDE
CHASE
INSIDE
CHASE
FIGURE24
FIGURE25
FIGURE26

14
WS-415-099/03.16.99
FINISHING
LOG PLACEMENTLOG PLACEMENT
LOG PLACEMENTLOG PLACEMENT
LOG PLACEMENT
PHAZERTM logs and glowing embers (available as an option
from your Napoleon dealer), exclusive to Napoleon Fireplaces,
provide a unique and realistic glowing effect that is different in
every installation. Take the time to carefully position the glow-
ing embers for a maximum glowing effect.
1. Place the front log, as shown, centered along the inside
front edge of the burner tray.
2. Place the back log onto the log support bracket, located on
the rear wall of the combustion chamber, pushing it as close to
the firebox wall as possible.
3. & 4. Set the two smaller logs into the pockets and pegs of
the front and back logs, respectively.
Log colours may vary. During the initial use of the fireplace, the
colours will become more uniform as colour pigments burn in
during the heat activated curing process.
POSITIONINGTHELOGS IMPROPERLY WILL CAUSEFLAME
IMPINGEMENTANDCARBONING.
4
1
2
3
FIGURE28

15
WS-415-099/03.16.99
FIGURE31
DOOR
STEEL LIP
OPTIONAL GLOWING EMBER INSTOPTIONAL GLOWING EMBER INST
OPTIONAL GLOWING EMBER INSTOPTIONAL GLOWING EMBER INST
OPTIONAL GLOWING EMBER INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
Tear the embers into pieces and place beneath the front log covering all of the burner area beneath and in front of the
hollowed out section of the log. Care should be taken to shred the embers into thin, small irregular pieces as only the
exposed edges of the fibre hairs will glow.
THEEMBER MATERIAL WILLONLY GLOWWHENEXPOSED TODIRECT FLAME;HOWEVER, CARE SHOULDBE TAKEN
TONOTBLOCK THEBURNERPORTS.
Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM logs glow
when exposed to direct flame. Use only certified "glowing embers" and PHAZERTM
logs available from your Napoleon / Wolf Steel Ltd. dealer.
DOOR, LOUVRE AND TRIM REMOVDOOR, LOUVRE AND TRIM REMOV
DOOR, LOUVRE AND TRIM REMOVDOOR, LOUVRE AND TRIM REMOV
DOOR, LOUVRE AND TRIM REMOVAL & INSTAL & INST
AL & INSTAL & INST
AL & INSTALLAALLA
ALLAALLA
ALLATIONTION
TIONTION
TION
ENSURE THAT THE DOOR IS PROPERLY CLIPPED ONTO THE
STEEL LIP TO PREVENT OVERHEATING, GLASS BREAKAGE AND/
OR DISCOLOURATION OF THE UPPER TRIM.
DOOR REMOVAL: Both top and bottom door trim must be
removed prior to door removal. Lift up the top trim and
unhook from the door. The bottom trim may be pulled off
and lifted out of the bottom door sill. FIGURE 30.
Remove the five screws securing the sides and bottom of
the door. Lift up and out.
DOOR AND TRIM INSTALLATION: When re-installing, re-
tighten screws snugly. DO NOT OVER-TIGHTEN.
Hang the door side trim onto each door side with the
notches towards the centre of the unit. The top and bottom
door trim may be installed next. Attach magnets to the top
and bottom door trim approximately 4" from either end.
Lift up the top trim and hook over the top of the door. The
bottom trim is inserted into the bottom door sill. Push in to
engage the magnets. Centre both side trims.
LOUVRES: The louvre assemblies are installed as illus-
trated in FIGURE 31. Optional arched door facias are
available at your local Napoleon/ Wolf Steel dealer.
FIGURE29
FIGURE30

16
WS-415-099/03.16.99
OPTIONAL BLOWER INSTALLATION
INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be
electrically connected and grounded in accordance with local codes. In the
absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
Canada orthe ANSI/NFPA 70-1996 NATIONAL ELECTRICAL CODE intheUnitedStates
If the fireplace was not previously equipped with a blower: route a
grounded 2-wire, 60hz power cable to the receptacle / junction box. At this point, it
must be strain relieved and insulated.
The three slots on the blower mounting
bracket allow ease of adjustment when
attaching the blower. For a quiet running
blower, do not allow the assembly to sit
on the firebox base.
Slide the vibration reducing pad (A) into the clip (C) and onto the threaded stud
(B) at the other end, piercing a hole into the pad. The blower must be able to be
positioned entirely onto the pad.
Tilt the blower onto its side. Slide it past the controls
and into the clip (C). Secure to the threaded stud using
the lock washer and wing nut provided. Ensure that the
blower does not touch the fireplace base or the firebox.
Attach the connectors from the black and white wires to
the thermodisc and secure the thermodisc bracket to
the securing stud at the bottom left of the unit using a
lock washer and wing nut. Ensure that the thermodisc
touches the firebox wall.
Attach the connectors from the black and red wires to
the blower.
Attach and secure the variable speed switch using the
nut provided. Plug the harness cord into the receptacle.
The wire harness provided in this kit is a universal harness. When installed, ensure that any excess
wire is contained, preventing it from making contact with moving or hot objects.
Because the blower is thermally activated, when turned on, it will automatically start approximately 10
minutes after lighting the fireplace and will run for approximately 30-45 minutes after the fireplace has
been turned off. Use of the fan increases the output of heat.
red
white
black
FIGURE32
FIGURE37
RECEPTACLE /
THERMODISC
GROUND
SCREW
JUNCTION BOX
FIGURE36
FIGURE35
FIGURE34
A
B
C
C
C
FIGURE33
SLOTS
ELONGATED

17
WS-415-099/03.16.99
OPTIONAL FAN INSTALLATION
ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be connected and grounded in
accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
Canada or the ANSI/NFPA 70-1990 NATIONAL ELECTRICAL CODE in the United States.
If the fireplace was not previously equipped with a fan: route a grounded 2-wire, 60hz power cable to the junction box.
At this point, it must be strain relieved and insulated.
The wire harness provided in this kit is a universal harness. When installed, ensure that any
excess wire is contained, preventing it
from making contact with moving or hot
objects.
Position the vibration reducing pad into the
clip and onto the threaded stud at the other
end, piercing a hole into the pad. The fan
assembly must be able to be positioned
entirely onto the pad.
Slide the fan assembly past the controls
and and into the clip. Secure using the lock washer and nut pro-
vided.
Attach the connectors from the black and white wires to the
thermodisc and secure the thermodisc bracket to the securing
stud at the bottom left of the unit using a lock washer and wing nut.
Ensure that the thermodisc touches the firebox wall.
GD36THERMOSTATICSENSORCONTROL
This optional kit is meant to be used only in conjunction with the GD65 Fan
Kit, shown above, which may be ordered from your Wolf Steel / Napoleon
dealer.
With the thermostatic sensor option, the fan, when turned on, becomes
thermally activated, and will automatically run approximately 15-30 minutes
after the fireplace has been lit and for approximately 30-45 minutes after the
fireplace has been turned off.
Use of the fan increases the output of heat.
Unplug the power cord from the receptacle. Connect all wires as shown.
Attach and secure the sensor assembly bracket to the securing stud located
next to the receptacle/junction box at the bottom left of the unit using the lock
washer and wing nut. Ensure that the thermodisc touches the firebox wall.
Plug the power cord back into the receptacle.
When installed, ensure that any excess wire is contained, preventing it from
making contact with moving or hot ob-
jects.
RECEPTACLE /
JUNCTION BOX
SLOTS
OPEN ENDED
BRACKET
VARIABLE SPEED/
PIEZO IGNITOR
JUNCTION BOX
THERMODISC
SENSOR ASSEMBLY
BRACKET
RECEPTACLE /
FIGURE39
FIGURE40
FIGURE41
FIGURE38

18
WS-415-099/03.16.99
OPERATION / MAINTENANCE
When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition
caused by the curing of the logs and the "burn-in" of internal paints and lubricants used in the manufacturing
process and will not occur again. Simply open a window to sufficiently ventilate the room.
After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may
emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a
window to sufficiently ventilate the room.
FOR YOUR SAFETY READ BEFORE LIGHTING:
AThis fireplace has a pilot which must be lit by hand while following these instructions exactly.
BBefore lighting, smell all around the fireplace area for gas and next to the floor because some gas is
heavier than air and will settle on the floor.
CUse only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn
by hand, Do not try to repair it. Call a qualified service technician. Force or attempted repair may result in
a fire or explosion.
DDo not use this fireplace if any part has been under water. Immediately call a qualified service technician
to inspect the unit and replace any part of the control system and any gas control touched by water.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
MAINTENANCEMAINTENANCE
MAINTENANCEMAINTENANCE
MAINTENANCE TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE FIREPLACE.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger-
ous operation. Verify proper operation after servicing. This fireplace and its venting system should be inspected before
use and at least annually by a qualified service person. The fireplace area must be kept clear and free of combustible
materials, gasoline or other flammable vapours and liquids. The flow of combustion and ventilation air must not be
obstructed.
1. In order to properly clean the burner and pilot assembly, remove the logs to expose both assemblies.
2. Keep the control compartment, logs, burner, air shutter opening and the area surrounding the logs clean by vacuum-
ing or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or are not burning
properly.
4. Check to see that the pilot flame is large enough to engulf the thermopile on one leg and reaches toward the burner
on the other leg.
5. Replace the cleaned logs.
6. Check to see that the main burner ignites completely on all openings when the gas knob for the burner is turned on.
A 5 to 10 second total light-up period is satisfactory. If ignition takes longer, consult your Napoleon dealer / distributor.
7. Check that the gasketing on the sides, top and bottom of the door is not broken or missing. Replace if necessary.
BURNER
ELECTRODE
PILOT
THERMOPILE
THERMO-
COUPLE
INSTRUCTIONS TO TURN OFF GAS:
1.Turn off all electrical power to the unit if service is to be performed.
2.Push in gas control knob slightly and turn clockwise to off. DO NOT FORCE.
FLAME
ADJUSTMENT
KNOB
O
T
P
I
L
L
O
I
H
T
P
I
L
O
N
O
F
F
O
PILOT
ON/OFF
KNOB
LIGHTING INSTRUCTIONS
WARNING: The gas valve has an interlock device which will not allow the pilot burner to be lit until the thermocouple
has cooled. Allow approximately 60 seconds for the thermocouple to cool.
When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.
1. Stop! Read the above safety information on this label.
2. Turn off all electric power to the fireplace.
3. Turn the gas knob clockwise to off.
4. Wait five (5) minutes to clear out any gas. If you smell gas in-
cluding near the floor. Stop! Follow "B" in the above safety informa-
tion on this label. If you don't smell gas go the next step.
5. Turn gas knob counter-clockwise to pilot.
6. Depress slightly and hold gas knob while lighting the pilot with
the push button ignitor. Keep knob depressed for one minute, then
release. If pilot does not continue to burn, repeat steps 3 through 5.
7. With pilot lit, depress and turn gas knob
counter-clock-wise to on.
8. If equipped with remote on-off switch/ther-
mostat, main burner may not come on when
you turn valve to on. Remote switch must be
in the on position to ignite burner.
9. Turn on all electric power to the fireplace.

19
WS-415-099/03.16.99
ADJUSTMENTS
PILOT BURNER ADJUSTMENTPILOT BURNER ADJUSTMENT
PILOT BURNER ADJUSTMENTPILOT BURNER ADJUSTMENT
PILOT BURNER ADJUSTMENT
Adjust the pilot screw to provide properly sized
flame. Turn in a clockwise direction to reduce the
gas flow. FIGURES 42 & 43.
VENTURI ADJUSTMENTVENTURI ADJUSTMENT
VENTURI ADJUSTMENTVENTURI ADJUSTMENT
VENTURI ADJUSTMENT
Natural gas models have air shutters set at ¼ (.250") inch open. Pro-
pane gas models have air shutters set at 3/8 (.375) inch open. Closing
the air shutter will cause a more yellow flame, but can lead to carboning.
Opening the air shutter will cause a more blue flame, but can cause
flame lifting from the burner ports. The flame may not appear yellow
immediately; allow 15 to 30 minutes for the final flame colour to be
established. FIGURE 44.
AIRSHUTTER ADJUSTMENTMUSTONLYBEDONE BYA QUALIFIEDGASINSTALLER!
P
I
P
I
PILOT SCREW
L
O
T
N
O
L
O
T
H
I
L
O
F
F
O
FIGURE42
NOTES:
FLAME MUST ENVELOP
UPPER 3/8" TO 1/2" OF
THERMOCOUPLE &
THERMOPILE
PILOT
THERMOPILE BURNER
ELECTRODE
THERMO-
COUPLE
FIGURE43
FIGURE44

20
WS-415-099/03.16.99
REPLACEMENTS
ORDERING REPLACEMENT PORDERING REPLACEMENT P
ORDERING REPLACEMENT PORDERING REPLACEMENT P
ORDERING REPLACEMENT PARAR
ARAR
ARTSTS
TSTS
TS
Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts
can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following
information: 1. Model & Serial Number of fireplace 3. Part Number 5. Finish
2. Installation date of fireplace 4. Description of part
REPLACEMENT PREPLACEMENT P
REPLACEMENT PREPLACEMENT P
REPLACEMENT PARAR
ARAR
ARTSTS
TSTS
TS FOR WARRANTY REPLACEMENT PARTS, APHOTOCOPY OF THE ORIGINAL INVOICE WILL BE
REQUIRED TO HONOUR THE CLAIM.
PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
WS-135-053 BACK LOG
WS-135-054 FRONT LOG
WS-135-056 RIGHT LOG
WS-135-055 LEFT LOG
GL-617 LOG SET ASSEMBLY
WS-385-33 NAPOLEONLOGO
WS 573-008 HIGH TEMPERATURE SEALANT
WS 100-35 BURNER
WS 455-23 NATURAL GAS PILOT ORIFICE
WS 455-24 PROPANE GAS PILOT ORIFICE
WS 725-25 NATURAL GAS VALVE
WS-725-26 PROPANE GAS VALVE
WS-430-001 CERAMIC MAGNET
GD660 STANDARD WALL SWITCH & 20FT OF WIRE
GA GD 715.11 POLISHED BRASS UPPER LOUVRE
GA GD 010.391 POLISHED BRASS LOWER LOUVRE ASSEMBLY
WS-660-5 ON/OFF TOGGLE SWITCH
GA GD 225.36 BLACK DOOR FRAME
WS 300-20 GLASS ONLY
GA GD 321K BLACK DOOR C/W GLASS
GA-GD-010.454 GLASS C/WGASKET
GD-562.09 DOOR GASKET (105 INCHES)
GA-GD-020.042 PKG OF 5 DOOR SCREWS
GA GD 010.376 BOTTOM DOOR TRIM
GA GD 715.136 TOP DOOR TRIM
WS-100-39 PROPANE GAS PILOT ASSEMBLY
WS 100-38 NATURAL GAS PILOT ASSEMBLY
WS 455-03 #54 PROPANE GAS ORIFICE
WS 455-040 #41 NATURAL GAS ORIFICE
WS-750-09 IGNITER WIRE
WS 357-01 PIEZO IGNITER
WS 680-04 THERMOPILE
WS-680-05 THERMOCOUPLE
VENT KITSVENT KITS
VENT KITSVENT KITS
VENT KITS
GD220 (5 FOOT)GD220 (5 FOOT)
GD220 (5 FOOT)GD220 (5 FOOT)
GD220 (5 FOOT)
PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
GD-010.397 4" FLEXIBLE ALUMINUM LINER (5 FT) C / W SPACERS
WS 410-17 7" FLEXIBLE ALUMINUM LINER (5 FT)
GD330 (10 FOOT)GD330 (10 FOOT)
GD330 (10 FOOT)GD330 (10 FOOT)
GD330 (10 FOOT)
PART NO.PART NO.
PART NO.PART NO.
PART NO. DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
GS 10.300 4" FLEXIBLE ALUMINUM LINER (10 FT) C / W SPACERS
WS 410-018 7" FLEXIBLE ALUMINUM LINER (10 FT)
GD10.370 WALL SUPPORT ASSEMBLY
P
I
P
I
L
O
T
N
O
I
L
O
T
H
L
O
F
F
O
WS-135-053
WS-135-055 WS-135-056
WS-135-054