Napoleon IR3N-1 User manual

EN
W415-1342 / 10.01.14
FR
PG
41
$10.00
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.napoleonfireplaces.com • [email protected]
1.36D
CERTIFIED FOR CANADAAND UNITED STATES USING ANSI/CSAMETHODS.
SAFETY INFORMATION
!WARNING
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certified kit is used.
If the information in these instructions
are not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with the appliance and
shall be installed.
CERTIFIED
Decorative Product: Not for use as a heating appliance.
BARRIER
SAFETY BARRIER
CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA 2.22 FOR VENTED GAS FIREPLACES.
IR3N-1
NATURAL GAS
IR3P-1
PROPANE

2
W415-1342 / 10.01.14
TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 MINIMUM CLEARANCE TO COMBUSTIBLES 5
2.3 GENERAL INSTRUCTIONS 5
2.4 GENERAL INFORMATION 6
2.5 RATING PLATE INFORMATION 7
3.0 INSTALLATION 8
3.1 LEVELLING THE APPLIANCE 8
3.2 CHIMNEY CONNECTION 9
3.3 GAS INSTALLATION 10
4.0 FINISHING 11
4.1 MINIMUM MANTEL CLEARANCES 11
4.2 SAFETY SCREEN & DOOR REMOVAL / INSTALLATION 12
4.3 LOG PLACEMENT 13
4.4 OPTIONAL ROCK PLACEMENT 14
4.5 GLOWING EMBERS 14
4.6 LOGO PLACEMENT 14
4.7 BATTERY INSTALLATION 14
5.0 ELECTRICAL INFORMATION 15
5.1 WIRING DIAGRAM 15
6.0 OPERATION 16
6.1 OPERATING AND LIGHTING INSTRUCTIONS 16
6.2.1 GENERAL REMOTE TRANSMITTER LAYOUT 17
6.2.2 PROGRAMMING 17
6.2 OPERATION 17
6.2.3 TURNING "ON" THE APPLIANCE 18
6.2.4 TURNING "OFF" THE APPLIANCE 18
6.2.5 HAND HELD REMOTE TRANSMITTER OPERATIONS 18
6.2.6 TEMPERATURE DISPLAY 18
6.2.8 SETTING THE TIME 19
6.2.9 SETTING THE TIMER FUNCTION 19
6.2.10 FLAME HEIGHT 19
6.2.7 LOW BATTERY 19
7.0 ADJUSTMENTS 20
7.1 PILOT BURNER ADJUSTMENT 20
7.2 VENTURI ADJUSTMENT 20
7.3 FLAME CHARACTERISTICS 20
7.4 LP CONVERSION 21
8.0 MAINTENANCE 22
8.3 ANNUAL MAINTENANCE 23
8.1 CARE OF GLASS 23
8.2 CARE OF PLATED PARTS 23
8.4 DOOR GLASS REPLACEMENT 24
8.5 BURNER REMOVAL 25
8.6 VALVE TRAIN REPLACEMENT 25
9.0 REPLACEMENTS 26
10.0 OVERVIEW 27
11.0 ACCESSORIES 29
12.0 VALVE TRAIN ASSEMBLY 31
13.0 VENTING 32
14.0 TROUBLESHOOTING 33
15.0 WARRANTY 36
16.0 SERVICE HISTORY 37
17.0 NOTES 38
NOTE: The camera icon indicates video tutorials are available as additional reference, visit http://
www.napoleonfireplaces.com/category/product-support/support-centre/
EN
NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

3
W415-1342 / 10.01.14
EN
Venting, see “INSTALLATION
- CHIMNEY CONNECTION”
section.
Rating Plate, see “RATING
PLATE INFORMATION”
section.
Logs, see “FINISHING - LOG
PLACEMENT” section.
Batteries, see “BATTERY INSTALLATION” section.
Receiver, see “PROGRAMMING” section.
SAFETY BARRIER
1.0 INSTALLATION OVERVIEW
Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled,
and may be accepted for disposal at your local recycling center. Check with your municipality for recycling
instructions.

4
W415-1342 / 10.01.14
EN
2.0 INTRODUCTION
3.2C
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS
PROHIBITED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance
according to operating instructions could cause fire or injury.
• Risk of fire or asphyxiation do not operate appliance with fixed glass removed.
• Do not connect 110 volts to the control valve.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may
be sharp.
• Do not burn wood or other materials in this appliance.
• Children and adults should be alerted to the hazards of high surface temperature and should stay away to
avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance, install an
adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and
away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and
draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot
surfaces. These screens and guards must be fastened to the floor.
• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating
the appliance.
• The appliance is a vented gas-fired appliance. Do not burn wood or other materials in the appliance
• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance
and venting system are kept clean. The appliance and its venting system should be inspected before use and at
least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from
carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials,
gasoline and other flammable vapors and liquids.
• Under no circumstances should this appliance be modified.
• This appliance must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.
• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system and any gas control which has been under water.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be
done by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent
exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping
through these openings can also cause the surrounding combustible materials to overheat and catch fire.
• Only doors / optional fronts certified with the appliance are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic
bags, these are not toys and should be kept away from children and infants.
• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well
as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon
Monoxide.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage of
decorations, a T.V. or other electronic components.
• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and
shall be installed.
• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this
appliance.
• Installation and repair should be done by a qualified service person. The appliance should be inspected
before use and at least annually by a professional service person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments,
burners and circulating air passageways of the appliance be kept clean.

5
W415-1342 / 10.01.14
EN
2.1 DIMENSIONS
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to
conform with local codes. Installation practices vary from region to region and it is important to know the
specifics that apply to your area, for example in Massachusetts State:
• This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth
of Massachusetts.
• The appliance damper must be removed or welded in the open position prior to installation of an appliance
insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36 inches (914mm).
• A Carbon Monoxide detector is required in all rooms containing gas fired appliances.
• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” (1219mm) FROM
THE FRONT FACE OF THE APPLIANCE.
SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT
WHEN THE APPLIANCE IS OPERATING.
FIRE RISK. EXPLOSION HAZARD.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE
TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35 mb).
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.
USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING
COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
!
WARNING
Thisappliance mustberecessed intoa ventednoncombustible wood-burningappliance (prefabricatedor masonry)
only. The minimum appliance opening size in which the appliance is to be installed is:
HEIGHT 211/2" (546mm) WIDTH 29" (737mm) DEPTH *131/2" (343mm)
The minimum allowable chimney flue size is 7" (178mm) round.
*Add 4" (102mm) for optional blower.
The minimum distance, from the bottom of a combustible mantel projecting 3" (76mm) maximum from the wall
to the top of the appliance, is 14" (356mm) (See MINIMUM MANTEL CLEARANCES section).
NOTE: A NON-COMBUSTIBLE HEARTH MUST PROTRUDEA MINIMUM OF 12" (305mm) FROM THE
APPLIANCE.
2.2 MINIMUM CLEARANCE TO COMBUSTIBLES
21"
533mm
20 1/2"
521mm
12"
305mm
17 1/2"
445mm
9 1/2"
241mm
17 1/2"
445mm
29 5/8"
753mm
28 3/4" 730mm
13 1/4"
337mm
23 5/8"
600mm
SAFETY BARRIER
2.3 GENERAL INSTRUCTIONS

6
W415-1342 / 10.01.14
EN
2.4 GENERAL INFORMATION 4.1B
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
A
NSI Z223.1 and NFPA 54 in the United States.
A
s long as the required clearance to combustibles is
maintained, the most desirable and beneficial location
for an appliance is in the center of a building, thereby
allowing the most efficient use of the heat created. The location of windows, doors and the traffic flow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a floor or roof joist.
If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
® (NFI) as NFI Gas
Specialists
www.ncertied.org
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION
AND QUALITY!
IR3-1
NG LP
Altitude (FT) 0-4,500 0-4,500
Max. Input (BTU/HR) 24,000 24,000
Max. Output (BTU/HR) 18,480 18,480
Efficiency (w/the fan on) 77% 77%
A.F.U.E. (maximum value) 76% 76%
Min. Inlet Gas Supply Pressure 4.5" Water Column (11mb) 11" Water Column (27mb)
Max. Inlet Gas Supply Pressure 7" Water Column (17mb) 13" Water Column (32mb)
Manifold Pressure (Under Flow Conditions) 3.5" Water Column (9mb) 10" Water Column (25mb)
When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of specific
recommendations from the local authority having jurisdiction, the certified high altitude input rating shall be
reduced at the rate of 4% for each additional 1,000ft (305m). Expansion / contraction noises during heating up
and cooling down cycles are normal and to be expected.
This appliance is not approved for closet or recessed installations. It is approved for bathroom, bedroom and
bed-sitting room installations and is suitable for mobile homes. The natural gas model is suitable for installation
in a mobile home that is permanently positioned on its site and fuelled with natural gas.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
appliance and shall be installed.
64.2%
IR3-1

7
W415-1342 / 10.01.14
EN
2.5 RATING PLATE INFORMATION
INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model, venting and gas type of the appliance.
For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
NOTE: The rating plate must remain with the appliance at all times. It must not be removed.
SERIAL NUMBER/NO. DE SERIE: IR3/CIR3
WARNING: DONOTADDANYMATERIALTOTHEAPPLIANCETHATWILLCOME IN
CONTACT WITHTHE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER
WITHTHEAPPLIANCE.
DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE.
AVERTISSEMENT: N'A JOUTEZ PAS A CETAPPAREILAUCUN MATERIAU DEVANT
ENTRER ENCONTACTAVECLES FLAMMESAUTREQUECELUIQUIESTFOURNIAVECCET
APPAREIL PAR LE FABRICANT.
PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPAREIL DE CHAUFFAGE.
W385-1971 / A
CERTIFIED FOR
CERTIFIEE POUR CANADA USA
CERTIFIED
REFERENCE #161746
CONFORMS TO / CONFORME AUX: ANSI Z21.50-2014, CERTIFIED TO / CERTIFIE CSA 2.22-2014 VENTED GAS FIREPLACE / FOYER À GAZ VENTILÉ.
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE. ONTARIO L4M 0G8 CANADA
ELECTRICAL RATING: 115V 1.5AMP 60HZ
THE APPLIANCE MUSTBE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE OWNER’S
INSTALLATION MANUALFOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS
NECESSARYAFTER SERVICING THE VENT-AIR INTAKE SYSTEM.
WARNING: FOR INSTALLATION INTOA VENTED NON-COMBUSTIBLE FIREPLACE ONLY. THE MINIMUM
FIREPLACE SIZE IS: HEIGHT 20.5”, DEPTH 13.25”, WIDTH 29”. THE MINIMUM INSIDE FLUE SIZE IS 6”. THE
MINIMUM DISTANCE FROM THE BOTTOM OFA COMBUSTIBLE MANTELPROJECTING AMAXIMUM 3” FROM
THE WALLTO THE TOPOF THE UNIT IS 12”. SEE OWNER’S MANUAL FOR GREATER EXTENSIONS.
OPTIONAL FAN KIT - GZ550-KT, GD65.
CLASS : 115V, 1.5AMP, 60HZ
L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE A WOLF STEEL. REFERER AU MANUEL
D’INSTALLATION DE PROPRIETAIRE POUR L’EVACUATION PRECISE. IL EST IMPORTANT DE BIEN REINSTALLER ET RESCELLER
L’EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D’AIR.
ATTENTION : POUR INSTALLATION DANS UN FOYER VENTILE EN MACONNERIE. LES DIMENSIONS MINIMUMS SONT: HAUTER
19.75”, PROFONDEUR 13.25”, LARGEUR 29”. LE DIAMETRE INTERIEUR MINIMUM DE CONDUIT D’EVACUATION EST DE 6”. LA
DISTANCE MINIMALE, DU BAS DU MANTEAU COMBUSTIBLE FORMANT UNE PROJECTION MAXIMALE DE 3” DU MUR AU DESSUS DE
LA GARNITURE NORMALE EST 12”. REFERER AU MANUEL D’INSTALLATION POUR DES EXTENSIONS PLUS GRANDES.
SOUFFLERIE OPTIONELLE
GZ550-KT, GD65.
N E PAS ALLUMER SI DES ENFANTS OU D’AUTRES INDIVIDUS À RISQUE SONT À PROXIMITÉ
DU FOYER. FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR INSTALLATION DANS UNE
CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUDIO.APPROPRIÉ POUR
INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION ESTCONFORME AUX
EXIGENCES DE LA NORME CAN/CSAZ240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU
GAZ, EN VIGUEUR AU CANADA, OUAUX ÉTATS-UNIS, SELON LA NORME DE SÉCURITÉ ETDE
CONSTRUCTION DE MAISONS MANUFACTURÉES,TITRE 24 CFR, SECTION 3280. DANS LE
CAS OÙ CETTE NORME DES ÉTATS-UNIS NE PEUTÊTRE APPLIQUÉE, SE RÉFÉRER À LA
NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES
INSTALLATIONS DANS LES MAISONS MANUFACTURÉES, LES SITES ET LES COMMUNAUTÉS,
DO NOT TURN ON IF CHILDREN OR OTHERATRISK INDIVIDUALS ARE NEAR THE
FIREPLACE. DIRECT VENT GAS FIREPLACE. SUITABLE FOR BEDROOM,
BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE
HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT
STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA
OR IN THE UNITED STATES THE MANUFACTURED HOME CONTRUCTION AND
SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT
APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR
MANUFACTURED HOME INSTALLATIONS, SITESAND COMMUNITIES, ANSI / NFPA
.
IR3N IR3PCIR3N CIR3P
MODEL
4500FT (0-1370m) ALTITUDE/ELEVATION 4500FT (0-1370m)
24,000 BTU/h INPUT/ALIMENTATION 24,000 BTU/h
18,000 BTU/h REDUCED INPUT/ALIMENTATION REDUITE 18,000 BTU/h
MANIFOLD PRESSURE: 3.5” WATER COLUMN
PRESSION AU COLLECTEUR: 3.5” D’UNE COLONNE D’EAU
MINIMUM SUPPLY PRESSURE: 4.5” WATER COLUMN
PRESSION D’ALIMENTATION MINIMALE: 4.5” D’UNE COLONNE D’EAU
MAXIMUM SUPPLY PRESSURE: 7.0” WATER COLUMN
PERSSION D’ALIMENTATION MAXIMALE: 7.0” D’UNE COLONNE D’EAU
P4: 64.2%
MANIFOLD PRESSURE:10” WATER COLUMN
PRESSION AU COLLECTEUR:10” D’UNE COLONNE D’EAU
MINIMUM SUPPLY PRESSURE: 11” WATER COLUMN
PRESSION D’ALIMENTATION MINIMALE: 11” D’UNE COLONNE D’EAU
MAXIMUM SUPPLY PRESSURE: 13” WATER COLUMN
PERSSION D’ALIMENTATION MAXIMALE: 13” D’UNE COLONNE D’EAU
P4: 64.2%
NATURAL GAS / GAZ MODEL PROPANE MODEL
ANSI/NFPA501A . POUR UNE UTILISER SEULMENT AVEC BARRIÈRE W565-0133. SUIVEZ
LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE MANUEL D'INSTALLATION
501A . FOR USE ONLY WITH BARRIER W565-0133. FOLLOW THE INSTALLATION
INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL
THIS VENTED GAS FIREPLACE IS NOT FOR USE WITH
AIR FILTERS. FOR USE WITH GLASS DOORS CERTIFIED
FOR THIS UNIT ONLY. NOT FOR USE WITH SOLID FUEL.
CE FOYER À GAZ VENTILÉS NE DOIT PAS ÊTRE UTILISÉ CONJOINTEMENT AVEC DES
FILTRES À AIR. UTILISERAVEC LES PORTES VITRÉES HOMOLOGUÉES AVEC CETTE
UNITÉ SEULEMENT. UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC
CETAPPAREIL.
SAMPLE
SAMPLE
SAMPLE
SAMPLE
THAT
WIL
L
COME
IN
B
Y
THE MANU
F
ACTURER
E
DA USA
E
E
L
FIREPLACE / FOYER À GAZ V
EL LTD.
LEON ROAD, BARRIE. ONTARIO L4
THE APPROPRIATE WOLF STEEL VENT KITS.
SPECIFICS. PROPER REINSTALLATIONAND RESEAL
VENT-AIR INTAKE SYSTEM.
VENTED NON-COMBUSTIBLE FIREPLACE ONLY. T
TH 13.25”, WIDTH 29”. THE MINIMUM INSIDE FL
OF ACOMBUSTIBLE MANTEL PROJECTIN
. SEE OWNER’S MANUAL FOR GREAT
LUMER SI DES ENFANTS OU D’AUTRES INDIV
FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR I
OUCHER, UNE SALLE DE BAIN ET UN STUDI
NS UNE MAISON MOBILE SI SON INST
NORME CAN/CSA Z240MH SÉRIE D
CANADA, OU AUX ÉTATS-UN
ONS MANUFACTURÉE
ÉTATS-UNIS NE
NORME RELATIVE AU CRITÈRE DE MESUR
INSTALLATIONS DANS LES MAISONS MA
PL
IR3P
MODEL
TUDE/ELEVATION
450
T/ALIMENTAT
UT/ALIMENTATION REDUITE
R COLUMN
OLONNE D’EAU
” WATER COLUMN
UNE COLONNE D’EAU
E:
7.0” WATER CO
0” D’UNE COLONNE D’
P4:
64.2%
MANIFOLD PR
PRESSIONA
MINIMUM
PRESSION
MAXIMUM SU
PERSSION D’AL
P4:
64.2%
PROPANE MO
ANSI/NF
R UNE UTILISE
LES INSTRUCTIONS D'INSTALLAT
H
S CERTIFIED
H SOLID FUEL
E FOYER
F
RE
UN
C
SA

8
W415-1342 / 10.01.14
EN
3.0 INSTALLATION
3.1 LEVELLING THE APPLIANCE
68.4B
Clean out ashes from the inside of the wood-burning appliance. Make sure that the chimney and wood-burning
appliance are in a clean and sound condition and constructed of non-combustible materials. If necessary have
any repair work done by a qualified person before installing the insert. Remove the existing appliance damper
or lock into an open position.
Using screws, attach the appliance warning tag
to the inside of the firebox of the appliance into
which the insert is being installed.
The sheet-metal parts of the appliance, in which
the gas appliance insert is to be installed, must
not be cut.
If the wood-burning factory-built appliance has
no gas access hole(s) provided, an access hole of 1½ inch (38.1mm) or less may be drilled through the lower
sides or bottom of the appliance in a proper workman like manner. This access hole must be plugged with non
-
combustible insulation after the gas supply line has been installed.
Ensure that existing chimney cleanouts fit properly.
The refractory, glass doors, screen rails, screen mesh and log grates may be removed from the existing
appliance before installing the gas appliance insert.
Smoke shelves, shields and baffles may be removed if attached by mechanical fasteners.
The ventilation openings in the existing appliance may be obstructed by the backer plates, aluminium trim etc.
but these parts are not to be applied so as to have an airtight seal.
!
WARNING
RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.
W385-0199_B
WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITHA GAS FIREPLACE
INSERT ONLYAND CANNOT BE USED FOR BURNING WOOD OR SOLID FUELS UNLESSALL ORIGINAL
PARTS HAVE BEEN REPLACED AND THE FIREPLACE IS RE-APPROVED BY THEAUTHORITY HAVING
JURISDICTION.
ATTENTION: CE FOYER AETE CONVERTI AFIN D’ETRE UTILISE SEULEMENT
COMME FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU
TOUTAUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALESAIENT
ETE REMPLACEES ET QUE LE FOYER SOITAPPROUVE DE NOUVEAU PAR LES AUTORITES
AYANT JURIDICTION.
ADVERTENCIA: ESTA CHIMENEASE REMODELÓ PARA USARSE SOLO CON UNA
INSERCIÓN DE CHIMENEAA GAS Y NO PUEDE USARSE PARAQUEMAR MADERA NI COMBUSTIBLES
SÓLIDOS, A MENOS QUE SE HAYAN REEMPLAZADO TODAS LAS PIEZAS ORIGINALES, Y LAAUTORI-
DAD JURISDICCIONAL LA HAYA VUELTO AAPROBAR.
Move the appliance close to its final position. This appliance is equipped with levelling screws located on the
base. Level using the levelling screws. Levelling the appliance will eliminate rocking or excessive noise when
the fan is in operation. Once the appliance is level, move it partially into place to allow for all connections to be
made. It is not practical to level the appliance once it has been installed. Determine the required depth prior to
installing the appliance and adjust the levelling screws accordingly. 67.2

9
W415-1342 / 10.01.14
EN
While the liners must be continuous from the appliance to the chimney cap, to
achieve the needed length, they may be coupled, using an approved coupler.
We recommend that exhaust vents that pass through unheated spaces,
such as tall exterior chimneys, be wrapped in a protective sleeve to minimize
condensation and reverse flow symptoms. See Trouble Shooting for details.
This appliance is approved for use with a 3" (76mm) exhaust and air intake.
A. OUTSIDE: Slip the one end of a liner a minimum of 2" (51mm) over
the sleeve of the air terminal. Secure using 3 screws. Then seal the
joint and screw heads with high temperature sealant. Repeat with
the other liner.
NOTE: We recommend that the other end of the exhaust liner be marked to eliminate the
exhaust liner being connected to the intake collar at the appliance.
B. Gently stretch the liners to the
required lengths and insert into
the chimney. Trim and fit the
flashing plate to suit the chimney
termination. Place the air terminal
onto the top of the chimney.
Make weather tight by sealing
with caulking (not supplied).
Fasten to the chimney with
screws and plugs (not supplied).
C. INSIDE: Remove the securing
screw from the front of the vent
mounting plate. Pull the vent
mounting plate only, back into
the track, to the front stop. Start
the slider back into position. Re-
secure the screw. The appliance
may now be pushed into its
final position inside the wood
burning appliance, and the screw
tightened until the slider has
been pulled tight to the front stop.
D. Route the flex liners through
the slider. Attach and secure
the liners to the vent mounting plate using the same procedure as before, ensuring that the marked
exhaust liner is attached to the exhaust collar.
FLASHING
PLATE
2” (50.8mm)
OVERLAP
SEALANT
HI-TEMP
INTAKE
EXHAUST
SECURING
SCREW
SLIDER
MOUNTING
PLATE
HIGH TEMP
SEALANT
2” (50.8mm)
OVERLAP
3” (76.2mm)
LINERS
EXHAUST
INTAKE
VENT MOUNT
ASSEMBLY
SAFETY BARRIER
3.2 CHIMNEY CONNECTION
Chimney installation must conform to both national and local code requirements. The chimney must be lined
with one 3" (76mm) diameter liner for intake and one 3" (76mm) diameter liner for exhaust. The minimum and
maximum vent lengths are 10 ft (3m) and 35 ft (11m) respectively.
Recommended kits come in 3 lengths:
2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:
GDI-320KT VENT KIT 20FT (6m)
GDI-325KT VENT KIT 25 FT (7m)
GDI-335KT VENT KIT 35 FT (11m)

10
W415-1342 / 10.01.14
EN
3.3 GAS INSTALLATION
30.1A
Installation and servicing to be done by a qualified installer. Do not use open flame.
• Move the appliance into position and secure.
• If equipped with a flex connector the appliance is designed to accept a 1/2” (13mm) gas supply.
Without the connector it is designed to accept a 3/8” (9.5mm) gas supply. The appliance is equipped
with a manual shut off valve to turn off the gas supply to the appliance.
• Connect the gas supply in accordance to local codes. In the absence of local codes, install to the
current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI
Z223.1 / NFPA 54 in the United States.
• When flexing any gas line, support the gas valve so that the lines are not bent or kinked.
• Check for gas leaks by brushing on a soap and water solution.
!
WARNING
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS
SPARKS OR OPEN FLAMES.
SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT
WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE
PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT
THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND
ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.
ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG.
VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.

11
W415-1342 / 10.01.14
EN
Combustible mantel clearance can vary
according to the mantel depth. Use the
graph to help evaluate the clearance
needed. These same requirements
apply to any combustibles protruding
on either side of the appliance.
H
DF
G
MANTEL DEPTH
0” (mm)
+
(
,
*
+
7
0
$
1
7
(
/
E
C
B
A
!
WARNING
RISK OF FIRE, MAINTAIN ALL SPECIFIED AIR SPACE CLEARANCES TO COMBUSTIBLES. FAILURE
TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE A FIRE OR CAUSE THE APPLIANCE TO
OVERHEAT. ENSURE ALL CLEARANCES (I.E. BACK, SIDE, TOP, VENT, MANTEL, FRONT, ETC.) ARE
CLEARLY MAINTAINED.
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION. 73.1
D
ABC
EF
H
G
201/2”
(520.7mm)
4.0 FINISHING
!
WARNING
RISK OF FIRE!
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
THE FRONT OF THE APPLIANCE MUST BE FINISHED WITH ANY NON-COMBUSTIBLE MATERIALS
SUCH AS BRICK, MARBLE, GRANITE, ETC., PROVIDED THAT THESE MATERIALS DO NOT GO
BELOW THE SPECIFIED DIMENSION AS ILLUSTRATED.
DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS
REMOVED, CRACKED, BROKEN OR SCRATCHED.
FACING AND/OR FINISHING MATERIAL MUST NEVER OVERHANG INTO THE APPLIANCE OPENING.
72.1A
MANTEL DIMENSIONS
Ref Height Ref Depth
A17" (432mm) E6" (152mm)
B16" (406mm) F5" (127mm)
C15" (381mm) G4" (102mm)
D14” (356mm) H3" (76mm)
4.1 MINIMUM MANTEL CLEARANCES

12
W415-1342 / 10.01.14
EN
4.2 SAFETY SCREEN & DOOR REMOVAL / INSTALLATION
!
WARNING
GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.
THE DOOR LATCHES ARE PART OF A SAFETY SYSTEM AND MUST BE PROPERLY ENGAGED. DO
NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.
FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR
OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR
SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.
BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO
THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.
75.1
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
appliance and shall be installed.
Before the glass door can be removed, the safety screen must be removed. Lift the safety screen off the 4
side pins, tilt the top forward and remove from the unit.
The optional front must be removed to allow the door to be opened or closed. Release the top left and right
door latches, located at the top of the door. Tilt forward and lift from slots.
Reverse these steps to re-install the safety screen and door. Ensure safety screen is installed correctly.
SAFETY SCREEN SAFETY SCREEN

13
W415-1342 / 10.01.14
EN
4.3 LOG PLACEMENT
!
WARNING
FAILURE TO POSITION THE LOGS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE
ONLY LOGS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE
PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED
IGNITION MAY OCCUR.
THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.
76.1A
E. Position the right charcoal strip
in front of the right middle log, lining
up the holes in the bottom with the
2 front right studs.
F. Position a pin (supplied) into the
left side hole of the rear log, move
the left crossover log into position,
lining up the top hole with the pin in
the rear log.
C. Place the right middle log into
position, lining up the two holes in
the bottom with the studs located on
the right side of the burner.
D. Position the left charcoal strip in
front of the left middle log, lining up
the holes in the bottom with the 2
front left studs.
PHAZERTM logs and glowing embers exclusive to Napoleon, provide a unique and realistic glowing effect that is
different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect.
Log colours may vary. During the initial use of the appliance, the colours will become more uniform as colour
pigments burn in during the heat activated curing process.
A. Place the rear log behind the left
and right log supports and ensure
that it's tight to the burner. Make sure
to centre the pilot in the notch.Adjust
the log supports tight to the log to
hold it in an upright position.
B. Place the left middle log into
position, lining up the two holes in
the bottom with the studs located
on the left side of the burner.
LOG SUPPORT
G. Position a pin into the right side
hole of the rear log, move the right
crossover log into position, lining
up the top hole with the pin in the
rear log.
A. Position the left and right log
support brackets (supplied) onto the
burner base. Secure with the screws
supplied. Make sure the brackets
face away from the firebox, as
shown.
LOG SUPPORT

14
W415-1342 / 10.01.14
EN
Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of
the small logs. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed
edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame;
however, care should be taken to not block the burner ports.
Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PHAZERTM
logs glow when exposed to direct flame. Use only certified "glowing embers" and PHAZERTM logs available
from your authorized dealer / distributor.
97.1A
Remove the backing o
f
the logo supplied and place on the glass viewing door,
as indicated. ½"(12.7mm)
LOGO
½"(12.7mm)
4.4 OPTIONAL ROCK PLACEMENT
4.5 GLOWING EMBERS
4.6 LOGO PLACEMENT
Before beginning with the installation, remove the door and all burner media from the appliance including logs
and charcoal strips. Retain the glowing embers.
D. Reinstall the glowing embers over the burner.
E. Reinstall the door.
!
WARNING
REAL ROCKS MUST NOT BE USED IN THIS APPLIANCE. HEAT WILL CAUSE THEM TO EXPLODE
A. Sit the two rock clusters on top
of the rear log support. Ensure the
clusters are sitting flat.
B. Place the large notched rocks
along the step behind the front
burner as desired.
C. Place the remaining rocks around
the burner as desired making sure
not to cover any burner ports (there
are no set locations).
4.7 BATTERY INSTALLATION
4 AA batteries must be installed in to the (DC battery pack) before operation is possible. The battery pack
is located in the bottom right corner of the appliance. The door may have to be removed to access, refer to
"DOOR REMOVALAND INSTALLATION" section. (Refer to "INSTALLATION OVERVIEW" for battery location).

15
W415-1342 / 10.01.14
EN
RECEIVER
GV60 VALVE
BATTERY
HOUSING
OFF ON
PSE PILOT
INTERRUPTER
BLOCK
BLACK WITH YELLOW TERMINAL END
BLACK WITH
RED TERMINAL END
RESET BUTTON
BLACK
(8 WIRE)
THERMOCOUPLE
WIRE
ORANGE
5.0 ELECTRICAL INFORMATION
5.1 WIRING DIAGRAM
This appliance comes equipped with a battery pack. Install 4 AA batteries into the holder that is connected to
the wire harness. Place near the front of the appliance for ease of changing batteries.
!
WARNING
DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WATER. CALL A QUALIFIED
SERVICE TECHNICIAN IMMEDIATELY TO HAVE THE APPLIANCE INSPECTED FOR DAMAGE TO THE
ELECTRICAL CIRCUIT.
RISK OF ELECTRICAL SHOCK OR EXPLOSION. DO NOT WIRE 110V TO THE VALVE OR TO THE
APPLIANCE WALL SWITCH. INCORRECT WIRING WILL DAMAGE CONTROLS.
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE
WITH LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA22.1 CANADIAN
ELECTRIC CODE IN CANADA OR THE CURRENT NATIONAL ELECTRIC CODE ANSI/NFPA NO. 70 IN
THE UNITED STATES.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
69.2

16
W415-1342 / 10.01.14
EN
6.0 OPERATION
When lit for the first time, the appliance will emit a slight odour for a few hours. This is a normal temporary
condition caused by the "burn-in" of internal paints and lubricants used in the manufacturing process and
will not occur again. Simply open a window to sufficiently ventilate the room.After extended periods of non-
operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for
a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to sufficiently
ventilate the room.
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH
THE GLASS DOOR OPENED OR REMOVED.
!
WARNING
6.1 OPERATING AND LIGHTING INSTRUCTIONS
OPERATING INSTRUCTIONS / INSTRUCTIONS D’OPERATION
FOR YOUR SAFETY READ BEFORE OPERATING / POUR VOTRE SÉCURITÉ LIRE AVANT DE FAIRE FONCTIONNER
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUC-
TIONS EXACTLY, AFIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONALINJURY OR
LOSS OF LIFE.
INITIAL LIGHTING OF THE PILOTAND MAIN BURNERS
MUST BE DONE WITH THE GLASS DOOR OFF.
DO NOT CONNECT VALVE OR WALL SWITCH TO ELEC-
TRICITY. SEE INSTALLATION INSTRUCTIONS.
A. THIS FIREPLACE IS EQUIPPED WITHAN IGNITION DEVICE WHICH AUTOMATI-
CALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT BY HAND.
B. BEFORE OPERATING SMELL ALLAROUND THE FIREPLACEAREA FOR GAS
AND NEXT TOTHE FLOOR BECAUSE SOME GAS IS HEAVIER THANAIR AND WILL
SETTLE ON THE FLOOR.
WHAT TO DO IF YOU SMELL GAS:
• TURN OFF ALL GAS TO THE FIREPLACE.
• OPEN WINDOWS.
• DO NOT TRYTO LIGHT ANY APPLIANCE.
• DO NOT TOUCHANY ELECTRIC SWITCH; DO NOT USEANY PHONE IN YOUR
BUILDING.
• IMMEDIATELY CALLYOUR GAS SUPPLIER FROM ANEIGHBOUR’S PHONE.
FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS.
• IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALLTHE FIRE DEPARTMENT.
C. DO NOT TRYTO REPAIR ANYPART OFTHIS ASSEMBLY. CALL AQUALIFIED
SERVICE TECHNICIAN. FORCE ORATTEMPTED REPAIR MAYRESULT INA FIRE
OR EXPLOSION.
D. DO NOT USE THIS FIREPLACE IFANY PART HAS BEEN UNDER WATER.
IMMEDIATELY CALLA QUALIFIED SERVICE TECHNICIAN TO INSPECT THE
FIREPLACE AND REPLACEANY PART OF THE CONTROL SYSTEMAND ANY GAS
CONTROL WHICH HAS BEEN UNDER WATER.
ATTENTION: SI CES INSTRUCTIONS NE SONT PAS OBSERVÉES A LA
LETTRE, UN FEU OU UNE EXPLOSION POURRAIT S’ENSUIVRE
CAUSANT DES DOMMAGESA LAPROPRIETE, DES BLESSURES
CORPORELLES OU PERTE DE VIE.
L’ ALLUMAGE INITIAL DE LAVEITLLEUSE ET DU BRULEUR PRINCIPAL
DOIT SE FAIRE AVEC LA PORTE VITREE ENLEVEE.
NE RACCORDEZ PAS LA SOUPAPE OU L’INTERRUPTEUR MURALA
L’ELECTRICITE.
CONSULTEZ LES INSTRUCTIONS D’INSTALLATION.
A. CETAPPAREIL EST MUNI D’UN DISPOSITIF D’ALLUMAGE QUI ALLUME LAVEILLEUSE
AUTOMATIQUEMENT.
N’ESSAYEZ PAS D’ALLUMER LAVEILLEUSE MANUELLEMENT.
B. AVANT D’ALLUMER SENTEZ L’AIR AUTOUR DE L’APPAREIL ETPRÈS DU PLANCHER (CERTAINS
GAZ SONT PLUS LOURDS QUE L’AIR ET SE DÉPOSERONT AU NIVEAU DU PLANCHER) POUR
DÉTECTER UNE FUITE POSSIBLE.
QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ:
• COUPEZ L’ALIMENTATION DE GAZ PRINCIPALE.
• OUVREZ LES FENETRES.
• N’ALLUMEZ AUCUN APPAREIL.
• NE TOUCHEZ PAS À AUCUN INTERRUPTEUR ÉLECTRIQUE; N’UTILISEZAUCUN TÉLÉPHONE
DANS VOTRE IMMEUBLE.
• APPELEZ IMMÉDIATEMENT VOTRE FOURNISSEUR DE GAZ D’UN TÉLÉPHONE VOISIN ET SUIVEZ
SES INSTRUCTIONS.
• SI VOUS NE POUVEZ PAS REJOINDRE VOTRE FOURNISSEUR DE GAZ, APPELEZ LE SERVICE
DES
INCENDIES.
C. N’ESSAYEZ PAS DE RÉPARER AUCUNE PIÈCE DE CETASSEMBLAGE. APPELEZ UN
TECHNICIEN QUALIFIÉ. FORCER OU TENTER DE RÉPARER L’ASSEMBLAGE POURRAIT CAUSER
UN FEU OU UNE EXPLOSION.
D. N’UTILISEZ PAS CET APPAREIL SI UN DE SES COMPOSANTS À ÉTÉ SUBMERGÉ. CONTACTEZ
IMMÉDIATEMENT UN TECHNICIEN DE SERVICE QUALIFIÉ POUR INSPECTER L’APPAREIL ET
REMPLACER TOUT SYSTÈME DE CONTRÔLE DE GAZTOUCHÉ PAR L’EAU. W385-1907
LIGHTING INSTRUCTIONS / INSTRUCTIONS D’ALLUMAGE
1. STOP! READALL INFORMATION OF OPERATING AND LIGHTING
INSTRUCTIONS BEFORE PROCEEDING.
2. TURN REMOTE/WALLSWITCH TO THE “OFF” POSITION.
3. TURN OFF ELECTRIC POWER TO THE FIREPLACE AND/OR REMOVE THE
BATTERIES.
4. THIS FIREPLACE IS EQUIPPED WITH AN IGNITION DEVICE WHICH
AUTOMATICALLY LIGHTS THE PILOT. DO NOT TRYTO LIGHT THE PILOT
BY HAND.
5. OPEN THE GLASS DOOR.
6. TURN MANUAL SHUTOFF VALVE CLOCKWISE TO “OFF”.
7. WAIT FIVE (5) MINUTES TO CLEAR OUTANY GAS. IF YOU SMELLGAS
INCLUDING NEAR THE FLOOR, STOP! FOLLOW “B” OF THE OPERATING
INSTRUCTIONS. IF YOU DON’T SMELL GAS GO TO THE NEXT STEP.
8. CLOSE THE GLASS DOOR.
9. TURN MANUAL SHUTOFF VALVE COUNTER-CLOCKWISE TO “ON”.
10. TURN ON ALL ELECTRIC POWER TO THE FIREPLACE AND/OR
REINSTALL THE BATTERIES.
11. TURN REMOTE/WALL SWITCH TO THE “ON” POSITION.
1. ARRÊTEZ! LISEZ TOUTES LES INSTRUCTIONS DE FONCTIONNEMENT
ET D’ALLUMAGE AVANT DE CONTINUER.
2. TOURNEZ L’INTERRUPTEUR MURAL/TÉLÉCOMMANDE MANUELLE À “OFF”.
3. COUPEZ L’ALIMENTATION ÉLECTRIQUE À L’APPAREIL ET/OÙ ENLEVEZ
LES PILES.
4. CETAPPAREIL EST MUNI D’UN DISPOSITIF D’ALLUMAGE QUIALLUME
LAVEILLEUSE AUTOMATIQUEMENT, N’ESSAYEZ PAS D’ALLUMER LA
VEILLEUSE MANUELLEMENT.
5. OUVREZ LA PORTE VITRÉE.
6. TOURNEZ LASOUPAPE DE SECTIONNEMENT MANUELLE VERS LA
DROITE A “OFF”.
7. ATTENDEZ CINQ (5) MINUTES POUR QUE LE GAZ PUISSE
S’ÉCHAPPER. SI VOUS DÉTECTEZ UNE ODEUR DE GAZ, ARRÊTEZ!
SUIVEZ « B » DANS LES INSTRUCTIONS DE FONCTIONNEMENT. S’IL
N’YA PAS D’ODEUR DE GAZ, PASSEZ À L’ÉTAPE SUIVANTE.
8. FERMEZ LA PORTE VITRÉE.
9. TOURNEZ LASOUPAPE DE SECTIONNEMENT MANUELLE VERS LA
GAUCHE A “ON”.
10. RÉTABLISSEZ L’ALIMENTATION ÉLECTRIQUE AU FOYER ET/OÙ
INSTALLEZ LES PILES.
11. TOURNEZ L’INTERRUPTEUR MURAL/TÉLÉCOMMANDE MANUELLE À “ON”.
1. TURN OFF ALL ELECTRICAL POWER TO THE FIREPLACE IF SERVICE IS
TO BE PERFORMED.
2. TURN MANUAL SHUTOFF VALVE CLOCKWISE TO “OFF”. DO NOT
FORCE.
1. COUPEZ L’ALIMENTATION ÉLECTRIQUEAU FOYER SI UN TRAVAIL
D’ENTRETIEN DOIT SE FAIRE.
2. TOURNEZ LASOUPAPE D’ARRÉT MANUELLE VERS LA DROITE
À “OFF” NE FORCEZ PAS.
TO TURN OFF GAS / INSTRUCTIONS POUR COUPER LE GAZ
MANTEMPTIMER
P1 P2 AUX
F
Cam
pm
:

17
W415-1342 / 10.01.14
EN
6.2 OPERATION
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH
THE GLASS DOOR OPENED OR REMOVED.
!
WARNING
MANTEMPTIMER
P1
P2
F
Cam
pm
:
LOW BATTERY
INDICTOR
SIGNAL INDICTOR
TEMPERATURE
DISPLAY
TIME DISPLAY
MODES OF
OPERATION
TIMER DISPLAY
ON/OFF
TEMPERATURE
SETTING
SET BUTTON
OFF BUTTON
LARGE FLAME BUTTON
SMALL FLAME BUTTON
6.2.1 GENERAL REMOTE TRANSMITTER LAYOUT
6.2.2 PROGRAMMING
A. Press and hold the receiver's reset button until you hear two beeps. (First beep is short, second beep
is long.) Release the button after the second beep, refer to "INSTALLATION OVERVIEW" for receiver
location.
B. Within the subsequent 20 seconds press and hold the small flame button on the remote transmitter
until you hear two additional short beeps confirming the code is set, refer to "GENERAL REMOTE
TRANSMITTER LAYOUT". (NOTE: One long beep indicates the sequence has failed or wiring is
incorrect).
NOTE: This is a one time setting only, and is not required after changing the batteries of the remote transmitter
or receiver.

18
W415-1342 / 10.01.14
EN
A. Using the remote transmitter press the "OFF" button.
NOTE: To turn the appliance on after pressing the "OFF" button, you must wait 30 seconds for both
burners to turn off. The appliance will shut off if no change has occured to the flame height or if the
appliance has not turned on for a period of 5 days.
A. Press the "Set" button to change modes.
B. The modes change in the following order:
NOTE: Refer to "GENERAL REMOTE TRANSMITTER LAYOUT".
MAN TEMP TEMP TIMER MAN
• For flame height adjustment in Manual Mode MAN double click the large flame button to
increase to the highest flame height. Double click the small flame button to decrease to the
lowest flame height. Press the large flame button to increase flame height or the small flame
button to decrease flame height. NOTE: Holding the small flame button for too long
will switch the appliance to pilot mode. To turn the appliance off completely press the
"OFF" button.
• For Daytime Temperature Mode TEMP the appliance must be set to standby mode (pilot
ignited). The default temperature setting for this mode is 23°C / 74°F. (Daytime Temperature
mode is set by comparing the set temperature and room temperature, the flame height is then
adjusted automatically to achieve this Daytime Temperature setting.)
• For Nighttime Temperature Mode TEMP the appliance must be set to standby mode (pilot
ignited). (Nighttime Temperature mode is set by comparing the night time set temperature and
room temperature, the flame height is then adjusted automatically to achieve this Nighttime
Temperature setting.)
• Timer Mode
TIMER the appliance must be set to standby mode (pilot ignited). There are two
timer settings available (P1 and P2) allowing the appliance turn off and to turn on at specified
times. NOTE: The "TIMER DISPLAY" indicates the set temperature every 30 seconds.
6.2.3 TURNING "ON" THE APPLIANCE
A. Place the "ON/OFF" switch in the "ON" position by the receiver, refer to "INSTALLATION OVERVIEW"
for location.
B. Using the remote transmitter simultaneously press the large flame button and the OFF button until
you hear a short beep, this confirms the start of the appliance, you can then release both buttons. (The
ignition process has begun once continuous beeping has begun).
C. Wait several seconds for the appliance to ignite. After main ignition the remote will default to the
Daytime Temperature Mode TEMP .
NOTE: Refer to "GENERAL REMOTE TRANSMITTER LAYOUT".
6.2.4 TURNING "OFF" THE APPLIANCE
6.2.5 HAND HELD REMOTE TRANSMITTER OPERATIONS
NOTE: Press the "OFF" button and the small flame button simultaneously until the temperature
display changes from Fahrenheit to Celsius, and vice versa. When changing from Fahrenheit to Celsius
the clock will change from a 12 hour to 24 hour clock, r efer to "GENERAL REMOTE TRANSMITTER
LAYOUT".
A. To set Daytime Temperature Mode quickly press the SET button, scrolling to the desired mode, then
hold the SET button until the "TEMP" on the display flashes.
B. To increase the Daytime Temperature press the large flame button . To decrease the Daytime
Temperature press the small flame button . To use this setting as the new temperature press the OFF
button.
6.2.6 TEMPERATURE DISPLAY

19
W415-1342 / 10.01.14
EN
A. Using the remote transmitter you may set the flame directly to the "HI" setting by double clicking the
large flame button . Increasing the flame height can also be done by pressing and holding the large
flame button .
B. Using the remote transmitter you may set the flame directly to the "LO" setting by double clicking the
small flame button . Decrease the flame height can also be done by pressing and holding the small
flame button .
NOTE: For fine adjustment tap the large flame button or small flame button when using the remote
transmitter. If the small flame button is held too long the main burner will turn off.
NOTE: Time display will flash upon battery installation or when the large and small flame buttons are
pressed simultaneously.
A. To set the hour press the large flame button .
B. To set the minutes press the small flame button .
C. Press the "OFF" button to set the time.
A. To set the Timer Mode quickly press the SET button, scrolling to the desired mode.
B. To scroll through P1 , P1 , P2 ,P2 briefly press the set button.
C. Once the desired timer function is shown on the display and the time flashes, press the large flame
button to adjust the hour and the small flame button to adjust the minutes. Press the "OFF" button
to set the time.
NOTE: The default setting for the Timer Function is as follows: P1 6:00am and P2 8:00pm, P2
11:50am and P2 11:50pm, refer to "GENERAL REMOTE TRANSMITTER LAYOUT".
6.2.8 SETTING THE TIME
6.2.9 SETTING THE TIMER FUNCTION
6.2.10 FLAME HEIGHT
C. To set Nighttime Temperature Mode quickly press the SET button, scrolling to the desired mode, then
hold the SET button untill the "TEMP" on the display flashes.
D. To increase the Nighttime Temperature press the large flame button . To decrease the Nighttime
Temperature press the small flame button . To use this setting as the new temperature press the OFF
button.
NOTE: When in regular operation the remote will always show the room temperature. Thermostat
function adjusts the flame height according to the difference between the set temperature and the
actual room temperature; as the room temperature gets closer to the set point it will adjust the flame
down.
A. Frequent beeping for 3 seconds when the appliance turns on indicates low battery on the remote
receiver. The battery pack is located on the bottom right side of the appliance, refer to "INSTALLATION
OVERVIEW" for location.
B. Low battery indicator is in the top right corner of the remote, we also recommend replacing the
batteries every two years.
NOTE: When low battery occurs the appliance will shut down. The appliance will shut off if no change
has occurred to the flame height or the appliance has not turned on for a period of 5 days.
6.2.7 LOW BATTERY

20
W415-1342 / 10.01.14
EN
IR3-1
NG 1/16” (1.6mm)
LP 3/8" (9.5mm)
Adjust the pilot screw to provide properly sized flame. Turn in a
clockwise direction to reduce the gas flow.
Check Pressure Readings:
Inlet pressure can be checked by turning screw (A) counter-clockwise
2 or 3 turns and then placing pressure gauge tubing over the test point.
Gauge should read as described on the chart below. Check that
main burner is operating on “HI”.
Outlet pressure can be checked the same as above using
screw (B). Gauge should read as described on the chart
below. Check that main burner is operating on “HI”.
AFTER TAKING PRESSURE READINGS, BE SURE TO
TURN SCREWS CLOCKWISE FIRMLY TO RESEAL. DO
NOT OVERTORQUE.
Leak test with a soap and water solution.
Prior to pilot adjustment, ensure that the pilot
assembly has not been painted. If overspray or
painting of the pilot assembly has occurred remove
the paint from the pilot assembly, or replace. Fine
emery cloth or sandpaper can be used to remove the paint from the pilot hood, electrode and flame sensor.
39.8A
A
B
PILOT
SCREW
FLAME MUST ENVELOP
UPPER 3/8” (9.5mm) TO 1/2”
(12.7mm) OF THERMOCOUPLE
PILOT
BURNER
ELECTRODE
THERMOCOUPLE
3/8” - 1/2”
(9.5mm - 12.7mm)
MANUAL
KNOB
Pressure
Inlet
Outlet
Natural Gas
(inches) Natural Gas (millibars) Propane (inches) Propane
(millibars)
7"
(MIN. 4.5")
3.5"
13"
(MIN. 11")
10"
17.4mb
(MIN. 11.2mb)
8.7mb
32.4mb
(MIN. 27.4mb)
24.9mb
This appliance has an air shutter that has been factory set open according
to the chart below:
Regardless of venturi orientation, closing the air shutter will cause a more
yellow flame, but can lead to carboning. Opening the air shutter will cause a
more blue flame, but can cause flame lifting from the burner ports. The
flame may not appear yellow immediately; allow 15 to 30 minutes for the
final flame colour to be established.
AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED
INSTALLER!
AIR
SHUTTER
OPENING
VENTURI
BURNER
ORIFICE
49.1
7.0 ADJUSTMENTS
7.1 PILOT BURNER ADJUSTMENT
7.2 VENTURI ADJUSTMENT
It’s important to periodically perform a visual check of the pilot and
burner flames. Compare them to the illustration provided. If any
flames appear abnormal call a service person.
FLAME MUST ENVELOP
UPPER 3/8” (9.5mm) TO 1/2”
(12.7mm) OF THERMOCOUPLE
PILOT
BURNER
ELECTRODE
THERMOCOUPLE
3/8” - 1/2”
(9.5mm - 12.7mm)
54.6
7.3 FLAME CHARACTERISTICS