Napoleon LINEAR PATIOFLAME GPFL48 User manual

APPLY SERIAL NUMBER LABEL FROM CARTON
Serial No.
XXXXXX000000
MODEL NO.
N415-0239 MAR 17/11
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This gas pao ame must be used only outdoors in a well-venlated space and must not be used
inside a building, garage, screened-in porch, gazebo or any other enclosed area.
WARNING
Do not try to light this appliance without reading
the “LIGHTING” instrucons secon of this manual.
Do not store or use gasoline or other ammable
liquids or vapors in the vicinity of this or any other
appliance. An L.P. cylinder not connected for
use must not be stored in the vicinity of this or
any other appliance. If the informaon in these
instrucons is not followed exactly, a re or explosion
may result, causing property damage, personal injury
or death.
DANGER
IF YOU SMELL GAS:
• Shut o gas to the appliance.
• Exnguish any open ame.
• If odor connues, keep away from the
appliance and immediately call your gas
supplier or re department.
DANGER! CARBON MONOZIDE HAZARD
This appliance can produce carbon monoxide, which has no odor. Using it in an
enclosed space can kill you. Never use this appliance in an enclosed space such as a
camper, tent, car or home.
LINEAR PATIOFLAME
OUTDOOR GAS FIREPLACE
GPFL48 (WITHOUT ENCLOSURE)
GPFL48MHP (WITH ENCLOSURE)
427-O-02-5
Napoleon Appliance Corp.,
214 Bayview Dr., Barrie, Ontario, Canada L4N 4Y8 Phone: [phone]
Fax: [phone] email: [e-mail] web site: www.napoleongrills.com
WARNING! For Outdoor Use Only.

2
www.napoleongrills.com
NAPOLEON products are designed with superior components and materials, and are
as sem bled by trained crasmen who take great pride in their work. Every component has
been thoroughly inspected by a qualied technician before packaging and shipping to
en sure that you, the customer, receive the quality product you expect from NAPOLEON.
Napoleon® Gas Appliance 5 Year Limited Warranty
All stainless steel components (excluding burner screen) of your new NAPOLEON® gas
appliance are warranted against defects for ve years.
Components such as gas valves, thermocouples, igniters, logs, glass embers and gaskets are
covered and NAPOLEON® will provide replacement parts free of charge during the rst year
of limited warranty.
NAPOLEON shall not be liable for any transportaon charges, labor costs or export dues.
Condions And Limitaons
NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary. Simply provide
your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® reserves the right to have its representave inspect
any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an authorized NAPOLEON® dealer your
heater is subject to the following condions and limitaons:
This limited warranty applies only while the unit remains at the site of original installaon, and only if the unit is installed in Canada or the United States.
This factory warranty is non-transferable and may not be extended whatsoever by any of our representaves.
Installaon must be done in accordance with the installaon instrucons included with the product and all local and naonal building and re codes.
This limited warranty does not cover damages caused by misuse; lack of maintenance, accident, alteraons, abuse or neglect and parts installed from other
manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and chemical cleaners, mechanical
breakage of logs and embers.
In the rst year only, this warranty extends to the repair or replacement of warranted parts which are defecve in material or workmanship provided that the
product has been operated in accordance with the operaon instrucons and under normal condions.
Aer the rst year, with respect to the President’s Limited Lifeme Warranty, NAPOLEON® may, at its discreon, fully discharge all obligaons with respect to
this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defecve parts).
Aer the rst year, NAPOLEON® will not be responsible for installaon, labour or any other costs or expenses related to the reinstallaon of a warranted part,
and such expenses are not covered by this warranty.
Notwithstanding any provisions contained in the President’s Limited Lifeme Warranty, napoleon’s responsibility under this warranty is dened as above and it
shall not in any event extend to any incidental, consequenal or indirect damages.
This warranty denes the obligaons and liability of NAPOLEON® with respect to the NAPOLEON® gas appliance and any other warranes expressed or implied
with respect to this product, its components or accessories are excluded.
This limited warranty does not cover damages resulng from the use of components not supplied with the appliance, or the use of fuel other than those specied.
Any damages to appliance due to weather, long periods of dampness, condensaon, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®.
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. The
warranty registraon card must be returned within fourteen days to register the warranty.
NAPOLEON® reserves the right to have its representave inspect any product or part thereof prior to honouring any warranty claim.

3
www.napoleongrills.com
WARNING! For Outdoor Use Only.
WARNING! Improper installaon, adjustment, alteraon, service or maintenance can cause injury or
property damage. Read the installaon, operang and maintenance instrucons thoroughly before installing
or servicing this gas pao ame.
Safe Operang Pracces
• THIS APPLIANCE IS HOT WHEN OPERATING AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• Installaon and repair should be done by a qualied service person. The appliance should be inspected
before use and at least annually by a qualied service person. More frequent cleaning may be required
as necessary. It is imperave the control compartment, burners and circulang air passageways of the
appliance be kept clean.
• Do not operate appliance before reading and understanding operang instrucons. Failure to operate
appliance according to operang instrucons could cause re or injury.
• Risk of burns. The appliance should be turned o and cooled before servicing.
• Do not install damaged, incomplete or substute components.
• Young children should be carefully supervised when they are in the vicinity of the appliance. Toddlers,
young children and others may be suscepble to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of
the vicinity and away from hot surfaces.
• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot
surfaces.
• Under no circumstances should this appliance be modied.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with
all plasc bags, these are not toys and should be kept away from children and infants.
• Do not leave appliance unaended when in use.
• For Outdoor use only.
• This appliance must not be used for cooking.
• This unit is not for use with solid fuel.
• Improper installaon, adjustment, alteraon, service, or maintenance can cause injury or property damage.
Read the installaon, operang and maintenance instrucons thoroughly before installing or servicing this
equipment.
• This appliance shall be used ONLY outdoors in a well-venlated space and shall NOT be used inside a building,
garage, or any other enclosed area.
• Cylinders must be stored outdoors in a well-venlated area out of reach of children. Disconnected cylinders
must have threaded valve plugs ghtly installed and must not be stored in a building, garage or any other
enclosed area.
• Storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply
(natural gas line or LP gas cylinder).
• If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the
appliance being put into operaon.
• Clothing or other ammable materials should not be hung from the appliance, or placed on or near the
appliance.
• Any guard or other protecve device removed for servicing the appliance must be replaced prior to
operang the appliance.
• Inspect the fuel supply connecon for signs of leakage (including the hose for LP models) before each use
of the appliance.
• The pressure regulator and hose assembly supplied with LP models must be used. Replacement pressure
regulators and hose assemblies must be those specied in this manual.
• The LP gas supply cylinder used with LP models must be constructed and marked in accordance with the
specicaons for LP-gas cylinders as required by the U.S. Department of Transportaon (DOT) or the Canadian
Transport Commission (CTC).
• The LP gas cylinder supply system must be arranged for vapour withdrawal.
• The LP-gas cylinder used must include a collar to protect the cylinder valve.
• When an LP model is not in use, the LP-gas must be turned o at the supply cylinder.
• To extend the life of your appliance, protect and cover it from the elements when not in use.
• This product must be installed by a licensed plumber or gas er when installed within the commonwealth
of Massachuses.

4
www.napoleongrills.com
General Informaon
This gas appliance is cered under Canadian and American Naonal Standards, ANSI Z21.97-2010 “Standard
for Outdoor Decorave Gas Appliance” and CAN/CGA 2.17-M91 (R2009) “Gas-Fired Appliance for use at High
Altude” and should be installed to conform with local codes. In absence of local codes, install to the current
CAN/CSA-B149.1 Propane Installaon Code in Canada or to the Naonal Fuel Gas Code, ANSI Z223.1 in the
United States.
This appliance should be installed and serviced by a qualied installer to conform with local codes.
Installaon pracces vary from region to region and it is important to know the specics that apply to your
area, for example: in Massachuses State:
• The appliance o valve must be a “T” handle gas cock.
• The exible connector must not be longer than 36 inches.
The installaon must conform with local codes or in the absence of local codes, with the Naonal Fuel Gas
Code ANSI Z223.1/INFPA 54 in the United States or CSA B149.1, Natural and Propane Installaon code in
Canada.
The appliance and its individual shut o valve must be disconnected from the gas supply piping system during
any pressure tesng of the system at test pressures in excess of 1/2 psig (3.5kPa).
This appliance must be isolated from the gas supply piping system by closing its individual manual shut o
valve during any pressure tesng of the gas supply piping system at test pressures equal to or less than
1/2 psig (3.5kPa).
The following clearances to combusble materials must be maintained:
Sides (all around) - 24 inches (610mm)
Top - 72 inches (1830mm)
• Always keep the appliance area clear and free from
combusble materials, gasoline, and other ammable
vapours and liquids.
• Do not locate appliance where it can get excessively
wet.
• Do not use this appliance if any part has been
under water. Immediately call a qualied service
technician to inspect the unit and to replace any
part of the control system and any gas control,
which has been underwater.
Geng Started
1. Remove all of the parts from the carton. Use the parts list to ensure all necessary parts are included.
2. Do not destroy packaging unl the pao ame has been installed and operates to your sasfacon.
3. Choose a locaon that meets the clearance to combusbles as outlined in the specicaon secon of this
manual. Take into consideraon the need for clear and easy access to the on/o valve AFTER the appliance
is installed and connected to the gas supply in order to safely turn o the burner.
4. Most stainless steel parts are supplied with a protecve plasc coang that must be removed prior to using
the pao ame.
5. Read and follow all instrucons in this manual before installing or servicing this gas pao ame.
If you have any quesons about assembly or pao ame operaon, or if there are damaged or missing parts
please call our Customer Care Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern Standard Time).
WARNING! This appliance is designed for non-combusble enclosures only, and must be installed and
serviced by a qualied installer to local codes.

5
www.napoleongrills.com
DIMENSIONS
INPUT
MODEL FUEL MAX. INPUT Btu/Hr
GPFL48N Natural Gas 60, 000
GPFL48P Propane Gas 60, 000
GAS INLET PRESSURES
NATURAL PROPANE
Inlet Pressure 7.0" w.c. 11.0" w.c.
MINIMUM CLEARANCE TO COMBUSTIBLES
INCHES MM
Side Walls 24 610
Top of unit to ceiling 72 1830
Specicaons
72”
(1829mm)
CENTRE OF PATIOFLAME
24”
(610mm)
24”
(610mm)
MAXIMUM
OVERHANG
13 1/2”
(343mm) 17 7/8”
(455mm)
47 1/2”
(1206mm)
51 7/8”
(1318mm)
11 7/8”
(302mm)
BURNER BASE ENCLOSURE
5 1/2”
(138mm)
BURNER BASE
ENCLOSURE

6
www.napoleongrills.com
This unit is designed with some unique features that allow for maximum installaon exibility.
1. The gas supply to the enclosure can come either from underneath or through the side of the enclosure.
2. The burner unit can be used either with or without the enclosure. Simply li the unit out of the enclosure
to separate. A second person is required to guide out the gas hose /regulator when removing the burner
unit from the enclosure. The burner unit can be placed directly on combusble surfaces, but the required
clearances to the sides and top must sll be maintained.
Installaon Opons
Ensure
bushing
snaps into
side panel
as shown.
The gas supply is shown entering
the side of the enclosure.
The gas supply is shown entering
the boom of the enclosure.
Two people are required to li burner unit from enclosure
Li burner unit from enclsoure using handles
If the gas supply is to be routed through the side of the enclosure remove the (3) screws from the cover plate
so the hole is exposed. Snap the bushing into the side panel to secure the hose in place. Slide the cover plate
over, and reinstall.

7
www.napoleongrills.com
3. The supply can feed either into the side of the burner base, or is fed from below the base. The gas line
needs to be disconnected from the gas valve and reconnected in order to do this. This must be done by
a licensed gas er and the connecons need to be leak tested according to the leak tesng instrucons
before using the unit.
4. The burner unit can be built into a non-combusble enclosure. The control module can be removed from
the burner unit and located up to 12” away from the burner unit. A cap is provided to close the opening in
the side of the burner module. The gas line needs to be disconnected and reconnected in order to do this.
This must be done by a licensed gas er and the connecons need to be leak tested according to the leak
tesng instrucons before using the unit.
4 x N570-0013
The gas supply is shown entering
the boom of the burner.
The gas supply is shown entering
the side of the burner.
Removing Control Panel

8
www.napoleongrills.com
12.600” C-C Mounng Locaon
#8 Wood Screw
Recommended
Raise the burner unit by 3/4”
above the enclosure surface
as illustrated.
Insert cap (N510-0012) into end of
control panel as shown.
WARNING! Materials placed around the burner unit will get extremely hot. They must be non- combusble
and must be able to expand and contract without cracking. Raise the burner unit above the enclosure by
(3/4”) to reduce the temperature of the enclosure surface. Tiled cement board is the preferred material.
WARNING! Cabinet frame, cabinet and counter top must be made from non-combusble material.
WARNING! You must have clear and easy access to the on/o valve AFTER the appliance is installed
and connected to the gas supply in order to safely turn o the burner.

9
www.napoleongrills.com
WARNING! If these instrucons are not followed exactly, a re causing death or serious injury may
occur.
Propane Cylinder Specicaons
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance with
the specicaons for LP-gas cylinders of the Naonal Standard of Canada, CAN/CSA-b339, Cylinders, Spheres
and Tubes for Transportaon of Dangerous Goods; and Commission, as applicable or the Specicaons for
LP- Gas Cylinders of the U.S. Department of Transportaon (D.O.T.). This appliance has been designed for use
with a 20 lb. (9.1 kg) or 30 lb (13.6 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connecon device compable with the connecon for
outdoor appliances. The propane cylinder must be provided with a shut-o valve terminang in a propane
cylinder valve type QCC1, and a safety relief device having direct communicaon with the vapor space of the
cylinder. The cylinder supply system must be arranged for vapor withdrawal and the cylinder shall include a
collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD (overll protecon device). Do
not store a spare LP-gas cylinder under or near this appliance. Never ll the cylinder beyond 80 percent full.
Use only the pressure regulator and hose assembly provided with this appliance. Replacement pressure
regulators and hose assemblies must be specied by the manufacturer. The regulator supplies a pressure of 11 inches. water
column to the appliance and has a QCC1 type ng. Cylinders to be used with this unit must be supplied with
a QCC1 cylinder valve. A QCC1 cylinder has a posive seang connecon, which will not allow g as ow unl a
posive seal has been achieved. It is also equipped with an excess ow device. In order to aain full ow to
the appliance, the valve must be in the o posion when the cylinder valve is turned on.
WARNING! A re will result if the gas supply hose makes contact with the underside of the appliance.
Gas Hook-Up Instrucons
LP (Propane) Gas
Aach cylinder retaining bracket supplied to the base of the cylinder. Then secure to the surface to which it
sits. Cylinder should be on a level surface.
Cylinder Retaining Bracket
1. Fasten the bracket to the boom of the propane bole using bolt
and nut supplied.
2. Tighten the lag screw into the mounng surface leaving approximately
1/4” of thread above the surface.
3. Slide propane bole into posion so that the bracket slides under
the head of the lag screw.
4. Tighten the lag screw onto the bracket.
5. For fastening to a concrete surface a concrete anchor will be
required. (Not supplied)
Cylinder Connecon: Ensure the gas regulator hose is kink
free. Remove the cap or plug from the cylinder fuel valve.
Insert the black QCC1 regulator nipple onto the QCC1 fuel
valve. Hand ghten clock wise. Do not use tools. Leak test
all joints prior to using the appliance. A leak test must be
performed annually and each me a cylinder is hooked up
or if a part of the gas system is replaced.
If this appliance is to be connected directly to a house
propane gas supply line, follow the instrucons for the
natural gas hook-up.

10
www.napoleongrills.com
CAUTION!
• Make sure cylinder valve is in its full o posion. (Turn clockwise to stop).
• Check cylinder valve features to ensure it has proper external mang threads. (Cylinder Valve Marked:
USE WITH TYPE 1)
• Inspect hose shipped with the unit for damage. Never aempt to use damaged or plugged equipment.
See your local LP Gas Dealer for repairs.
• When connecng regulator assembly to the cylinder valve, hand ghten black QCC1 nut clockwise to a
posive stop. DO NOT use a wrench to ghten. Use of a wrench may damage the quick closing coupling
nut and result in a hazardous condion.
• Locate the hose out of pathways where people may trip over it or in areas where the hose may be subject
to accidental damage.
• Open cylinder valve fully (counter-clockwise). Turn the on/o valve at the unit slowly to the on posion
and use a soapy water soluon to check all connecons for leaks as indicated in the diagrams before
aempng to light the appliance. If a leak is found, turn tank valve o and do not use the appliance unl
repairs can be made.
Enclosures For LP (Propane) Gas Supply Systems
If you build an enclosure for an LP gas cylinder, follow these recommended specicaons. You must also follow
local codes.
• An enclosure for an LP-gas cylinder shall be venlated by openings at both the upper and lower levels of
the enclosure.
This shall be accomplished by one of the following:
One side of the enclosure shall be completely open;
OR
For an enclosure having four sides, a top, and a boom:
a) At least two venlaon openings shall be provided in the sidewalls of the enclosure, located within 5 in (127 mm)
of the top of the enclosure, equally sized, spaced at 180 degrees, and unobstructed. The opening(s) shall have
a total free area of not less than 1 in2 per lb (14.2 cm2 / kg) of stored fuel capacity.
b) Venlaon opening(s) shall be provided at oor level of the enclosure and shall have a total free area of not
less than 1/2 in2 per lb (7.1 cm2 / kg) of stored fuel capacity. If venlaon openings at oor level are in a side
wall, there shall be at least two openings. The boom of the openings shall be 1 in (25.4 mm) or less from the
oor level and the upper edge no more than 5 in (127 mm) above the oor level. The openings shall be equally
sized, spaced at 180 degrees, and unobstructed.
c) Every opening shall have minimum dimensions so as to permit the entrance of a 1/8 inch (3.2mm) diameter
rod.
Venlaon openings in sidewalls shall not communicate directly with other enclosures of the appliance.
Cylinder valves shall be readily accessible for hand operaon. A door on the enclosure to gain access to the
cylinder valve is acceptable, provided it is non-locking and can be opened without the use of tools. Designs
using a cover to gain access to the cylinder and cylinder valve shall be provided with handles or equivalent at a
minimum of 180 degrees apart to facilitate liing of the cover.
There shall be a minimum clearance of 2 inches (50.8mm) between the lower surface of the oor of the LP gas
supply cylinder enclosure and the ground.
The design of the enclosure shall be such that (1) the LP gas supply cylinder(s) can be connected, disconnected
and the connecons inspected and tested outside the cylinder enclosure; and (2) those connecons which
could be disturbed when installing the cylinder(s) in the enclosure can be leak tested inside the enclosure.

11
www.napoleongrills.com
CYLINDER SIZE OPENING A AREA OPENING B AREA
20 lb (9.1 kg) 20 in2 (130 cm2) 10 in2 (65 cm2)
30 lb (13.6 kg) 30 in2 (195 cm2) 15 in2 (100 cm2)
The enclosure for the LP-gas cylinder shall isolate the cylinder from the burner compartment to provide:
a. Shielding from radiaon;
b. A ame barrier; and
c. Protecon from foreign material.
Be certain to mount or set the LP gas cylinder on a at surface and restrain it using the cylinder retaining
bracket to prevent it from pping.
OPENING
B
NON LOCKING DOOR
PARTITION TO ISOLATE CYLINDER
FROM PATIO FLAME
34” (864 mm)
RECOMMENDED
2” (51 mm)
MINIMUM
OPENING
A
5” (127 mm)
MAXIMUM
5” (127 mm)
MAXIMUM
1” (25.4 mm)
MAXIMUM

12
www.napoleongrills.com
Conversion to Natural Gas
WARNING! To avoid the possibility of burns conversions should only be done when the pao ame is
cool. Ensure burner is turned o. Turn gas o at source and disconnect the pao ame before beginning
conversion.
WARNING! Glass embers may have sharp edges wear safety glasses and gloves when handling.
WARNING! This conversion must be performed by a licensed gas er, and all connecons must be
leak tested before operang the pao ame.
Your pao ame can be easily converted to natural gas by following these steps:
1. Remove glass embers from the tray.
2. Remove the glass tray from the pao ame by removing the (18) screws that hold the tray in place.
3. Carefully li the glass tray from the pao ame and set aside. Take care not to damage or kink the
thermocouple wire.
4. Disconnect the stainless steel ex connector from the orice using (2) wrenches.
5. Unscrew the propane orice from the inside of the burner as illustrated.
6. Replace the propane orice with the natural gas orice supplied.
Note: The air shuer has been factory set and does not need to be adjusted.

13
www.napoleongrills.com
7. Reconnect the stainless steel ex connector to the orice and ghten using (2) wrenches.
8. Place the glass tray over the burner and fasten to the pao ame with the screws removed in step 2.
9. A leak test must be performed according to the leak tesng instrucons found in the manual.
Natural Gas Hook-Up
The gas appliance is designed to operate at an inlet pressure of 7 inches water column. The piping up to the
appliance is the responsibility of the installer. A exible metal connector is included to simplify the installaon
of the unit. Connect the exible connector to rigid pipe, copper tube or
an approved exible metal connector, which complies with Z21.4/CSA 6.10.
If using a gas hose (not supplied) connect the ared end of the hose to
the connector on the end of the ex tube as illustrated. Tighten using two
wrenches. (Do not use thread sealer/pipe dope.) Leak test all joints prior
to using the appliance. Piping and valves upstream of the quick disconnect
are not supplied. The gas supply pipe must be suciently sized to supply
the BTU/h specied on the rang plate, based on the length of the piping
run. The quick disconnect must not be installed in an upward direcon and
a readily accessible manual shut-o valve must be installed upstream of,
and as close to, the quick disconnect as is feasible.
Purge the gas supply line of any trapped air prior to the rst ring of the unit.
WARNING!
• The installaon must be performed by a licensed gas er, and all connecons must be leak tested before
operang the grill.
• Ensure all hose connecons are ghtened using two wrenches. Do not use Teon tape or pipe dope on
any hose connecon.
• Ensure the hose does not contact any high temperature surfaces or it may melt and leak causing a re.
• Locate the hose out of pathways where people may trip over it or in areas where the hose may be subject
to accidental damage.
• Leak test all the connecons using a soap and water soluon as per the leak tesng instrucons found in
the manual.

14
www.napoleongrills.com
Glass Ember Installaon
WARNING! Glass embers may have sharp edges, wear safety glasses and gloves when handling. Do
not change or substute the glass ember material provided with this appliance. If replacing, use only
replacement glass embers available from your local authorized dealer / distributor.
WARNING! Glass embers may have a ne oil residue that needs to be cleaned prior to installaon.
Clean the glass with mild dish soap, drain, rinse thoroughly and dry before installing.
1. Carefully pour the glass embers onto the appliance ember tray as shown.
2. Spread the glass embers over the tray and burner. The distribuon of clear glass over the burner will
inuence ame height.
3. Ensure no glass is placed on the ignion poron of the burner.
Finishing
ENSURE NO GLASS IS PLACED ON THE IGNITION PORTION OF THE BURNER,
DIFFICULTIES IN LIGHTING MAY RESULT.

15
www.napoleongrills.com
Leak Tesng Instrucons
WARNING! A leak test must be performed annually, or if a part of the gas system is replaced.
WARNING! Never use an open ame to check for gas leaks. Be certain no sparks or open ames are
in the area while you check for leaks. Sparks or open ames will result in a re or explosion, damage to
property, serious bodily injury, or death.
Leak tesng: This must be done before inial use, annually, and whenever any gas components are replaced
or serviced. Do not smoke while performing this test, and remove all sources of ignion. See Leak Tesng Diagram
for areas to check. Turn all burner controls to the o posion. Turn gas supply valve on.
Brush a half-and-half soluon of liquid soap and water onto all joints and connecons of the regulator, hose,
manifolds and valves.
Bubbles will indicate a gas leak. Either ghten the loose joint or have the part replaced with one recommended
by the Napoleon Customer Care department and have the grill inspected by a cered gas installer.
If the leak cannot be stopped, immediately shut o the gas supply, disconnect it, and have the grill inspected
by a cered gas installer or dealer. Do not use the grill unl the leak has been corrected.
DO NOT USE AN OPEN FLAME.
DO NOT USE AN OPEN FLAME.

16
www.napoleongrills.com
Lighng Instrucons
WARNING! Never use the appliance when it is raining. A cover has been provided to protect the burner
and glass embers when not in use. Remove the cover before starng the appliance.
WARNING! Keep face and body away from burner area when lighng.
WARNING! Ensure burner controls are in the o posion. Slowly turn on the gas supply valve.
1. Press and hold electronic igniter buon ( ).
2. Turn the burner control to the high posion, press and hold in. When the burner
lights, release the electronic igniter buon.
3. Connue to depress the burner control knob for 30 seconds and then release. If the
ame goes out, repeat the procedure.
4. Adjust the ame to the desired height with the burner control knob.
5. If the burner will not light with the electronic igniter, hold a lit long match or lit long
butane lighter to the ignion area of the burner and connue with step 2.
6. To shut down the burner turn the burner control knob clockwise to the o posion.
Then turn the gas o at the source (propane cylinder valve or natural gas supply valve).
WARNING! The propane cylinder is equipped with an excess ow device. Unless burners are turned
o prior to turning the cylinder on, only small ames and low heat will be achievable.
If lighng the unit with a match, clip the match into the supplied lighng rod.
Igniter
Open Cover

17
www.napoleongrills.com
Operang The Pao Flame
Inial Lighng: When lit for the rst me, the pao ame emits a slight odor. This is a normal temporary
condion caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and does
not occur again. Simply run the main burner on high for approximately one-half hour.
WARNING!
• Children and adults should be alerted to the hazards of high surface temperatures and should stay away
from the pao ame to avoid burns or clothing ignion.
• Children should be carefully supervised when they are in the area of the pao ame.
• Clothing or other ammable materials should not be hung from the pao ame, or placed on or near
the pao ame. The area above the enclosure may be extremely hot. Direct contact with these metal
surfaces should be avoided in order to prevent burns or clothing ignion.
• Any guard or protecve device removed for servicing the pao ame must be replaced prior to operang
the pao ame.
• Installaon and repair should be done by a qualied service person. The pao ame should be inspected
before each use and at least annually by a qualied service person. More frequent cleaning may be
required as necessary. It is imperave that the control compartment, burners and circulang air
passageways of the pao ame be kept clean.
WARNING!
• Never use the pao ame while it is raining.
• Always turn the pao ame o when raining.
• Never splash any liquid on the glass embers when the pao ame is operang.
• The glass embers will be extremely hot while operang, never try to touch them.
• Always ensure the pao ame stands rmly on level ground.
• Never use the pao ame if the burner is damaged. Inspect the burner before each use. Ensure that
no debris such as leaves; grass or other objects have entered or are on the pao ame. If the burner is
damaged it must be replaced prior to using the pao ame with a replacement burner specied by your
Napoleon dealer.
• Inspect the hose assembly before each use. If there is evidence of excessive abrasion or wear, or if the
hose is damaged it must be replaced prior to using the pao ame with a replacement hose assembly
specied by your Napoleon dealer.
NOTE! The pao ame has been designed with several safety features, which include a safety valve. If
the burner ame is exnguished the pao ame will automacally shut down.
WARNING! Any modicaon to the pao ame may compromise the safety of this appliance. Special
concern is as follows.
• Do not bypass thermocouple safety.
• Do not operate pao ame if any part has been under water. Immediately call a qualied service technician to
inspect the unit and replace any part of the control system and any gas control, which has been underwater.
WARNING! You must have clear and easy access to the on/o valve AFTER the appliance is installed
and connected to the gas supply in order to safely turn o the burner.
WARNING! Never use this pao ame for other than the intended use. Do not use this appliance to
prepare food.

18
www.napoleongrills.com
WARNING! Glass embers may have sharp edges, wear safety glasses and gloves when handling. Do not
change or substute the glass ember material provided with this appliance. If replacing, use only replacement
glass embers available from your local authorized dealer / distributor.
WARNING! To avoid the possibility of burns, maintenance should be done only when the pao ame
is cool. Avoid unprotected contact with hot surfaces. Ensure burner is turned o. Turn gas o at source and
disconnect the pao ame before servicing. Clean the pao ame in an area where cleaning soluons will
not harm decks, lawns, or paos. Do not use ammable, corrosive or abrasive cleaners.
Note: Stainless steel tends to oxidize or stain in the presence of chlorides and suldes, parcularly in coastal
areas and other harsh environments, such as the warm, highly humid atmosphere around pools and hot tubs.
These stains could be perceived as rust, but can be easily removed or prevented. To provide stain prevenon
and removal, wash all stainless steel surfaces every 3-4 weeks or as oen as required with fresh water and/or
stainless steel cleaner.
Control Panel: The control panel text is printed directly on the stainless steel and with proper maintenance
will remain dark and legible. To clean the panel, use only warm soapy water or stainless steel cleaner available
from your Napoleon dealer. Never apply abrasive cleaners on any stainless surfaces, especially the printed poron
of the control panel or the prinng will gradually rub o.
Maintenance / Cleaning Instrucons
Burner: The burner is made from heavy wall 304 stainless steel, but extreme heat and a corrosive environment
can cause surface corrosion to occur. This can be removed with a brass wire brush. Inspect the burner at least
annually for cracks, insect nests, excessive corrosion or any other damage. If the burner is damaged, it must be
replaced with a burner specied by the manufacturer before the appliance is put into operaon.
CAUTION! Beware of Spiders.
Spiders and insects are aracted to the smell of propane and natural gas. The burner is equipped with an insect
screen on the air shuer, which reduces the likelihood of insects building nests inside the burner but does not
enrely eliminate the problem. A nest or web can cause the burner to burn with a so yellow or orange ame or
cause a re (ashback) at the air shuer underneath the control panel. Other warning signs that may indicate a
problem are:
• Strong or unusual odor coming from the pao ame.
• Connued diculty or delayed ignion.
• Flame appears either very short or very long.
• Flame only burns part way across the burner.
• Excessive soot building up on the glass embers.
To clean the inside of the burner, it must be removed from the pao ame: Remove the glass embers and
examine the burner. If dirty, clean with a wire brush. Remove the screws that aach the glass ember tray and
the nuts from the boom of the burner. Slide the burner back and up wards to remove.
Cleaning: Use a exible venturi tube brush to clean the inside of the burner. Shake any loose debris from the
burner through the gas inlet. Check the burner ports and valve orices for blockages. Burner ports can close
over me due to debris and corrosion, use an opened paperclip or a drill bit to clean them The ports are easier
to clean if the burner is removed from the pao ame, but it can also be done with the burner installed.
WARNING! Hose: Check for abrasions, melng, cuts, and cracks in the hose. If any of these condions
exist, do not use the pao ame. Have the part replaced by your Napoleon dealer or qualied gas installer.
Cleaning Inside The Pao Flame: While washing your pao ame, be sure to keep the area around the burner
and pilot assembly dry at all mes.
WARNING! If the gas control is exposed to water in any way, DO NOT try to use the pao ame. The
gas control must be replaced.

19
www.napoleongrills.com
Cleaning The Outer Pao Flame Surface: Do not use abrasive cleaners or steel wool on any painted, or stain less
steel parts of your Napoleon Pao Flame. Doing so will scratch the nish. Exterior heater surfaces should be
cleaned with warm soapy water. To clean stainless surfaces, use a stainless steel or a non-abrasive cleaner.
Always wipe in the direcon of the grain. Over me, stainless steel parts discolor when heated, usually to a
golden or brown hue. This discoloraon is normal and does not aect the performance of the pao ame.
WARNING! The pao ame area must be clear and free from combusble materials, gasoline and
other ammable vapors and liquids. Do not obstruct the ow of combuson and venlaon air. Keep the
venlaon opening of the cylinder enclosure free and clear of debris.
Reinstallaon: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when
installing. Replace the glass embers. When the appliance is put back in service, check the burner ame paern
with the image below.
NORMAL
ABNORMAL

20
www.napoleongrills.com
Troubleshoong
Problem Possible Causes Soluon
Low heat / Low ame when
valve turned to high.
For propane - improper lighng
procedure.
For natural gas - undersized supply
line.
Ensure lighng procedure is followed carefully.
The valve must be in the o posion when the
tank valve is turned on. Turn tank on slowly to
allow pressure to equalize. See lighng
instrucons.
Pipe must be sized according to installaon code.
Burners burn with yellow
ame, accompanied by the
smell of gas.
Possible spider web or other debris. Thoroughly clean burner venturi. See general
maintenance instrucons.
Burner will not light with the
igniter, but will light with a
match.
Dead baery / or installed incor-
rectly.
Loose electrode wire or switch
terminal wires.
Improper gap at electrode p.
Replace with heavy duty baery.
Check that electrode wire is rmly pushed onto
the terminal on the back of the igniter. Check
that the lead wires from the module to the
ignion switch (if equipped) are rmly pushed
onto their respecve terminals.
The gap can be adjusted by bending the p in or
out. Unl a spark is achieved.
Burner will not stay lit when
control knob is released.
Knob not being held in long enough.
Too windy.
Glass or debris in ignion area of
the burner prevenng
thermocouple from being fully
engulfed in ame.
Dirty thermocouple or thermocouple
connecon.
Faulty thermocouple or valve.
Thermocouple must have me to heat up – hold
the knob in for 30 seconds aer the burner lights,
then release
Unit will shut down if winds are greater than
10mph (16km/h). Either locate to dierent area
or use when it is less windy.
Ensure there is no glass or other debris in ignion
area, and that the small hole below the thermo-
couple is unobstructed.
Clean the thermocouple and clean the connecon
between the valve and thermocouple. Ensure the
connecon is properly ghtened.
Replace thermocouple and / or valve.
Humming regulator. Normal occurrence on hot days. This is not a defect. It is caused by internal
vibraons in the regulator and does not aect the
performance or safety of the gas heater.
Humming regulators will not be replaced.
Burner output on “high”
seng is too low. (Rumbling
noise and uering blue
ame at burner surface.)
Lack of gas.
Supply hose is pinched.
Dirty or clogged orice.
Spider webs or other maer in
venturi tube.
Propane regulator in “low ow”
state.
Check gas level in propane cylinder.
Reposion supply hose as necessary.
Clean burner orice.
Clean out venturi tube.
Ensure lighng procedure is followed carefully. All
valves must be in the o posion when the tank
valve is turned on. Turn tank on slowly to allow
pressure to equalize. See lighng instrucons.