National Instruments PXIe-4339 User manual

INSTALLATION GUIDE AND TERMINAL BLOCK
SPECIFICATIONS
NI PXIe-4339 and TB-4339/B/C
8 Ch, 24-bit, 25.6 kS/s Universal Bridge Input Module
This document explains how to install, configure, and set up the NI PXIe-4339 SC Express
universal bridge module and TB-4339/4339B/4339C (TB-4339/B/C) terminal block. Driver
support for the NI PXIe-4339 was first available in NI-DAQmx 14.2. For the list of devices
supported by a specific release, refer to the NI-DAQmx Readme, available on the
version-specific download page or installation media.
Note The keying of these terminal blocks prevents them from connecting to other
modules that could be damaged by the voltage present on the terminal block.
However, you should only use these terminal blocks with their supported modules.
Contents
Electromagnetic Compatibility Guidelines .............................................................................. 2
What You Need to Get Started ................................................................................................. 2
Installation ................................................................................................................................ 3
Install the Software........................................................................................................... 3
Unpack and Install the Module......................................................................................... 3
Connect the Signals .......................................................................................................... 5
Install the Terminal Block ................................................................................................ 8
Confirm SC Express Module Recognition ....................................................................... 9
Run Test Panels ................................................................................................................ 10
Take an NI-DAQmx Measurement .................................................................................. 11
NI-DAQmx Channels and Tasks.............................................................................. 11
Configure a Task Using the DAQ Assistant in MAX .............................................. 11
Use Your SC Express Module in an Application ............................................................. 12
Programming Examples ........................................................................................... 12
Terminal Block Removal..........................................................................................................12
Module Removal ...................................................................................................................... 13
Create a Simulated Device .......................................................................................................14
More Information ..................................................................................................................... 15
Troubleshooting................................................................................................................ 15
Specifications (TB-4339/B/C).................................................................................................. 15
Calibration Interval................................................................................................................... 15

2|ni.com |NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications
Electrical ...........................................................................................................................15
Mechanical........................................................................................................................16
Physical .............................................................................................................................16
Environmental Specifications ........................................................................................... 16
Operating Environment............................................................................................. 16
Storage Environment ........................................................................................................ 17
Shock and Vibration ......................................................................................................... 17
Safety ................................................................................................................................17
Safety Standards ............................................................................................................... 17
Electromagnetic Compatibility ......................................................................................... 18
CE Compliance ................................................................................................................. 18
Online Product Certification............................................................................................. 18
Environmental Management............................................................................................. 19
World Wide Support and Services............................................................................................ 19
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with radio
and television reception and prevent unacceptable performance degradation, install and use this
product in strict accordance with the instructions in the product documentation.
Furthermore, any modifications to the product not expressly approved by National Instruments
could void your authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance, operate this product only with
shielded cables and accessories. Cables connected to the PXIe-4339 using the
TB-4339/B/C terminal block must use only twisted, shielded pair cables. Use one
twisted, shielded pair for each EX+/EX-, RS+/RS-, AI+/AI-, AO+/AOGND,
PFI0/DGND, and T+/DGND that is cabled. Cable shields must be terminated to
chassis ground at both ends.
What You Need to Get Started
To set up and use a NI PXIe-4339 module with a TB-4339/B/C terminal block, you need the
following items:
Hardware
– NI PXIe-4339 module
– TB-4339/B/C terminal block

NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications |© National Instruments |3
– NI PXI Express chassis
– Cabling and sensors as required for your application
Tools
– Number 1 and 2 Phillips-head screwdrivers
– 1/8 in. flathead screwdriver
– Long-nose pliers
– Wire cutter
– Wire insulation stripper
Documentation
–Read Me First: Safety and Electromagnetic Compatibility
–NI PXIe-4339 and TB-4339/B/C Installation Guide and Terminal Block Specifications
–NI PXIe-4339 User Manual
– NI PXI Express chassis user manual
You can download needed documents from ni.com/manuals.
Installation
Install the Software
Note You must be an administrator to install NI software and devices on your
computer.
Ensure that the following software is installed before installing the SC Express hardware:
1. Your application software, such as LabVIEW, LabWindows™/CVI™or .NET.
2. NI-DAQmx—NI PXIe-4339 modules were first supported in NI-DAQmx 14.2.
Note For detailed NI software version support, refer to the NI-DAQmx Readme.
Back up any applications before upgrading software or modifying the application.
Unpack and Install the Module
Remove the packaging and inspect the module. Contact NI if the module is damaged. Do not
install a damaged module.
Caution The module is static sensitive. Always properly ground yourself and the
equipment when handling or connecting to the module.

4|ni.com |NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications
Complete the following steps to install the SC Express module while referring to Figures 1
and 2:
Note To maintain forced air cooling in the PXIe system, refer to the Maintain
Forced-Air Cooling Note to Users.
1. Plug in your chassis before installing the NI PXIe-4339. The power cord grounds the
chassis and protects it from electrical damage while you install the module.
2. Make sure the chassis is powered off.
Caution To protect yourself, the chassis, and the NI PXIe-4339 from electrical
hazards, leave the chassis powered off until you finish installing the NI PXIe-4339
module.
3. Touch a metal part on the chassis to discharge any accumulated static electricity.
4. Identify a supported PXI Express slot in the chassis. SC Express devices can be placed only
in PXI Express Peripheral slots, PXI Express Hybrid Peripheral slots, and PXI Express
System Timing slots. Refer to the chassis documentation for details.
Figure 1. Symbols for PXI Express/ PXI Express Hybrid/ PXI Slots
5. Remove the filler panel, and touch any metal part of the chassis to discharge static
electricity.
6. Place the module edges into the module guides at the top and bottom of the slot.
Caution When installing the module, make sure both edges are positioned inside
the guides and that the module components do not come into contact with adjacent
modules.
7. Slide the module along the guides until it reaches the rear connector then seat the module
by pushing the front panel until it is flush with the front panel of the chassis.
1 PXI Express System Controller Slot
2 PXI Peripheral Slot
3 PXI Express Hybrid Peripheral Slot
4 PXI Express System Timing Slot
NI PXIe-1062Q
1 2 34

NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications |© National Instruments |5
8. Secure the module to the chassis using the front-panel captive screws, shown in Figure 2.
Tighten the screws to 0.31 N ·m (2.7 lb · in.).
Figure 2. Installing SC Express Modules
Connect the Signals
Caution For EMC compliance, operate this product with shielded cables and
accessories.
To connect signals to the terminal block, refer to Figures 3 and 4 while completing the following
steps:
Note You can find the pinout names and locations in Measurement & Automation
Explorer (MAX) at any time by right-clicking the device name under Devices and
Interfaces and selecting Device Pinouts.
1. Loosen the captive top cover screws and remove the top cover.
2. Loosen the strain-relief screws and remove the strain-relief bar.
3. Prepare the shielded signal wire by stripping the insulation no more than 7 mm (0.28 in.).
4. Run the shielded signal wires through the strain-relief opening.
1CaptiveScrews
NI PXIe-1062Q
COOLING CLEARANCE AND FANFILTER MAINTENANCE REQUIRED. SEE MANUAL.
1

6|ni.com |NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications
Figure 3. TB-4339/B/C Parts Locator Diagram
5. Insert the stripped end of the shielded signal wires fully into the appropriate terminal. Refer
to the label next to each screw terminal to determine the function of the terminal. The
NI PXIe-4339 User Manual provides more detailed wiring information. Make sure no
exposed wire extends past the screw terminal. Exposed wire increases the risk of a short
circuit that can cause circuit failure.
1 Strain-Relief Screws
2 Strain-Relief Bar
3 Tie Wrap Holes
4 Ground Lugs
5 Terminal Block to Module Connector
6 Captive Top Cover Screws
7 Top Cover
8 Tie Wraps
9 Shielded Signal Wires
3
1 2
1
4
6
7
6
5
4
8
9

NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications |© National Instruments |7
Figure 4. TB-4339/B/C Circuit Board Parts Locator Diagram
Note Refer to the NI PXIe-4339 User Manual for wiring diagrams showing various
ways to connect sensors to the TB-4339/B/C.
6. Tighten the terminal screws to a torque of 0.2 to 0.25 N · m (1.77 to 2.21 lb · in.).
Caution Any wires connected to the ground must be sufficiently insulated from
high voltage.
7. Use the ground lugs to attach a shield wire to the ground.
Note Refer to the NI PXIe-4339 User Manual for details about shielding the
signals.
8. Reinstall the strain-relief bar and tighten the strain-relief screws.
9. Use tie wraps to connect the shielded signal wires to the tie-wrap holes for additional strain
relief when necessary.
10. Reinstall the top cover and tighten the captive top cover screws.
Note For information about sensors, go to ni.com/sensors.
CH2 CH3
CH0 CH1
CH5CH4
CH6 CH7
PFI0
DGND
AOGND
AIGND
T-
T+
T-
T+
T-
T+
T+
T-
T-
T+
T-
T+
T-
T+
T-
T+
SCA
SCA
SCA
SCA
SCA
SCA
SCA
SCA SCA
SCA
SCA
SCA
SCA
SCA
SCA
SCA
RS+
EX+
AI+
AO+
RS-
EX-
AI-
RS+
EX+
AI+
AO+
RS-
EX-
AI-
AI+
AI-
EX-
AI+
AI-
EX-
AO+
RS-
EX+
AO+
RS-
EX+
RS+
AI+
AI-
EX-
AI+
AI-
EX-
AO+
RS-
EX+
AO+
RS-
EX+
RS+
RS+RS+
RS+
EX+
AI+
AO+
RS-
EX-
AI-
RS+
EX+
AI+
AO+
RS-
EX-
AI-
QTR
QTR
QTR
QTR
QTR
QTR
QTR
QTR
A1
B1
C1
o
S/N
o
155411A-01L
NI TB-4339
o
J15
CR2
R7
R4
R22
R10
R3
R21
J11
J10
U3
C5
C4
R6
R1
R18
C2
J8
R11R15
J18
J16
R23
R16
R9
R2
J12
J5
J3
J19
C3
U1
R24
J17
J6
J7
U4
R25
R12
R26
C6
J9
C1
R13
CR1
J13
R5
J2
R8
J14
R19
J4
J1
R14
R20
U2
FOR PATENTS: NI.COM/PATENTS
N114
N114
COPYRIGHT 2013

8|ni.com |NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications
Install the Terminal Block
Refer to Figure 5 to install the terminal block on the module while completing the following
steps:
1. Move the TB-4339/B/C into position in front of the NI PXIe-4339 and engage the
alignment feature with the guide on the associated module.
Figure 5. Installing the TB-4339/B/C on the NI PXIe-4339 Module
2. Attach the TB-4339/B/C to the NI PXIe-4339 module by pushing the terminal block
straight into the module. A spring mechanism will lock in the bottom of the terminal block.
3. Tighten the mounting screw at the top of the TB-4339/B/C to attach it to the NI PXIe-4339
module.
Note For safety purposes and to prevent damage to equipment when high voltages
are present, all SC Express modules and terminal blocks are keyed to prevent
connection between incompatible terminal blocks, modules, and/or cables.
4. Power on the chassis.
1 NI PXIe Controller
2 NI PXIe Chassis
3 Mounting Screw
4 TB-4339/B/C Terminal Block
5 NI PXIe-4339 Module
6 Alignment Feature
NI PXIe-1062Q
2
1
3
6
4
5
COOLING CLEARANCE AND FAN FILTER MAINTENANCE REQUIRED.SEE MANUA L.COOLING CLEARANCE AND FAN FILTER MAINTENANCE REQUIRED.SEE MANUAL.

NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications |© National Instruments |9
Figure 6 shows an example SC Express system setup.
Figure 6. Sample SC Express System
Confirm SC Express Module Recognition
To confirm module recognition, complete the following steps:
Note Software support for the NI PXIe-4339 is provided by NI-DAQmx. The DAQ
Getting Started Guide, which you can download at ni.com/manuals, offers
step-by-step NI-DAQmx instructions for installing software and hardware,
configuring channels and tasks, and getting started developing an application. For
detailed NI software version support, refer to the NI-DAQmx Readme.
1. Launch MAX.
2. Expand Devices and Interfaces, and expand the chassis in which the module is located to
confirm that MAX detects the module and terminal block. The terminal block should
appear beneath its associated module. If your module or terminal block is not listed, press
<F5> to refresh MAX. If the module is still not recognized, go to ni.com/support/
daqmx.
1 Terminal Block 2 Signal Input
NI PXIe-1062Q
1
COOLING CLEARANCE AND FAN FILTER MAINTENANCE REQUIRED.SEE MANUAL.COOLING CLEARANCE AND FANFILTER MAINTENANCE REQUIRED. SEE MANUAL.
2

10 |ni.com |NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications
Tip Using an NI-DAQmx simulated device, you can test NI-DAQmx applications
without installing hardware. Refer to the Create a Simulated Device section for
instructions for creating NI-DAQmx simulated devices.
3. Right-click the module name and select Self-Test. When the self-test completes, a
verification message appears. If an error occurs, refer to ni.com/support/daqmx.
For information about sensors, go to ni.com/sensors.
Run Test Panels
1. In MAX, expand Devices and Interfaces select the chassis in which the module is located.
2. Right-click the device, and select Test Panels.