National Instruments PXIe-8245 User manual

GETTING STARTED GUIDE
PXIe-8245
PXIe, 4-Port, 10/100/1000BASE-T PXI Ethernet Interface Module
This document describes how to install and configure the necessary hardware and software
components to begin using the PXIe-8245.
You need the following items to set up and use the PXIe-8245.
• PXIe-8245 GigE interface device
• Ethernet cable
• PXIe computer running Microsoft Windows 10 with at least one available slot
• PXI Platform Services software
• Optional software for developing applications:
– LabVIEW 2020
Note Before you begin, install and configure your chassis and controller.
Contents
Verifying the System Requirements..........................................................................................1
Unpacking the Kit..................................................................................................................... 2
PXIe-8245 Kit Contents............................................................................................................2
Preparing the Environment....................................................................................................... 2
Installing the Application Software and Driver........................................................................ 3
Installing the PXIe-8245........................................................................................................... 3
Confirming the Device is Recognized.............................................................................. 4
Front Panel................................................................................................................................ 4
Troubleshooting........................................................................................................................ 5
What Should I Do if the PXIe-8245 Does Not Appear in MAX?.................................... 5
Where to Go Next..................................................................................................................... 5
Worldwide Support and Services.............................................................................................. 6
Verifying the System Requirements
To use the PXIe-8245, your system must meet certain requirements. For more information
about minimum system requirements, recommended system, and supported application
development environments (ADEs), refer to the readme, which is installed or available at
ni.com/manuals.

Unpacking the Kit
Notice To prevent electrostatic discharge (ESD) from damaging the device, ground
yourself using a grounding strap or by holding a grounded object, such as your
computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose components or any
other sign of damage.
Notice Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
PXIe-8245 Kit Contents
The following items are included in the device kit:
• PXIe-8245
• Documentation:
–PXIe-8245 Getting Started Guide (this document)
–PXIe-8245 Safety, Environmental, and Regulatory Information
Preparing the Environment
Ensure the environment in which you are using the PXIe-8245 meets the following
specifications.
Operating environment
Ambient temperature range 0 °C to 55 °C
Relative humidity range 10% to 90%, noncondensing
Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient
temperature)
Pollution Degree 2
Indoor use only.
Note For complete specifications, refer to the specifications document for your
device at ni.com/manuals.
2| ni.com | PXIe-8245 Getting Started Guide

Installing the Application Software and Driver
Before installing your hardware, you must install the application software and device driver.
Install the software in the following order:
1. Install PXI Platform Services.
2. Install LabVIEW (optional).
Installing the PXIe-8245
Notice To prevent damage to the PXIe-8245 caused by ESD or contamination,
handle the module using the edges or the metal bracket.
1. Ensure the AC power source is connected to the chassis before installing the module.
The AC power cord grounds the chassis and protects it from electrical damage while you
install the module.
2. Power off the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior to
installation. Do not install a module if the backplane is damaged.
4. Remove the black plastic covers from all the captive screws on the module front panel.
5. Identify a supported slot in the chassis. The following figure shows the symbols that
indicate the slot types.
Figure 1. Chassis Compatibility Symbols
NI PXIe-1062Q
12 3 45
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
6. Touch any metal part of the chassis to discharge static electricity.
7. Place the module edges into the module guides at the top and bottom of the chassis. Slide
the module into the slot until it is fully inserted.
8. Secure the module front panel to the chassis using the front-panel mounting screws.
Note Tightening the top and bottom mounting screws increases mechanical
stability and also electrically connects the front panel to the chassis, which can
improve the signal quality and electromagnetic performance.
9. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize
cooling air flow, depending on your application.
PXIe-8245 Getting Started Guide | © National Instruments | 3

10. Power on the chassis.
Note The first time you start the development computer after installing the
hardware, allow several seconds for the drivers to load.
Confirming the Device is Recognized
To confirm that the device is properly installed and the hardware is recognized, complete the
following steps:
1. Select Start »All Programs »National Instruments »Measurement & Automation
Explorer to open Measurement & Automation Explorer (MAX).
2. Verify that the PXIe-8245 appears under My System »Devices and Interfaces .
Front Panel
The following figure shows the PXIe-8245 front panel.
Figure 2. PXIe-8245 Front Panel
PXIe-8245
1000BASE-T
0
1
2
3
The PXIe-8245 provides four standard Gigabit Ethernet ports (Port 0 to Port 3).
4| ni.com | PXIe-8245 Getting Started Guide

Table 1. Ethernet LED Status Definitions
LED Status Definition
Activity/Link Unlit No link
Green (Solid) Linked
Green (Blinking) Data activity
Link Speed Unlit 10 Mbps connection
Green 100 Mbps connection
Amber 1,000 Mbps connection
Troubleshooting
If an issue persists after you complete a troubleshooting procedure, contact NI technical
support or visit ni.com/support.
What Should I Do if the PXIe-8245 Does Not Appear in
MAX?
1. In the MAX configuration tree, expand Devices and Interfaces.
2. Expand the Chassis tree to see the list of installed hardware, and press <F5> to refresh
the list.
3. If the module is still not listed, power off the system, ensure that all hardware is correctly
installed, and restart the system.
4. Navigate to the Device Manager. Right-click the Start button, and select Device Manager
5. Verify the PXIe-8245 appears in the Device Manager.
a) Under an NI entry, confirm that a PXIe-8245 entry appears.
Note If you are using a PC with a device for PXI remote control system,
under System Devices, also confirm that no error conditions appear for the
PCI-to-PCI Bridge.
b) If error conditions appear, reinstall the PXI Platform Services driver.
Where to Go Next
Refer to the following figure for information about other product tasks and associated
resources for those tasks.
PXIe-8245 Getting Started Guide | © National Instruments | 5

SUPPORT
Services
ni.com/services
NI Community
ni.com/community
Software Support
ni.com/info>swsupport
Support
ni.com/support
SOFTWAREHARDWARE
Learn LabVIEW Basics
ni.com/gettingstarted
NI PXIe-8245 Specifications
ni.com/manuals
NI PXIe-8245 User Manual
ni.com/manuals
Worldwide Support and Services
The NI website is your complete resource for technical support. At ni.com/support, you have
access to everything from troubleshooting and application development self-help resources to
email and phone assistance from NI Application Engineers.
Visit ni.com/services for information about the services NI offers.
Visit ni.com/register to register your NI product. Product registration facilitates technical
support and ensures that you receive important information updates from NI.
NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,
78759-3504, USA. For up-to-date contact information for your location, visit ni.com/contact.
6| ni.com | PXIe-8245 Getting Started Guide

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for
information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their
respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your
software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find
information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer
to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how
to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS
TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.
Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable
limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2020 National Instruments. All rights reserved.
378323A-01 July 3, 2020