National Instruments PXIe-4162 User manual

GETTING STARTED GUIDE
PXIe-4162
PXIe, 12-Channel, ±24 V, 100 mA PXI Source Measure Unit
This document explains how to install, configure, and test the PXIe-4162. The PXIe-4162
ships with NI-DCPower driver software, which you can use to program the module.
Note Before you begin, install and configure your chassis and controller.
Contents
Verifying the System Requirements..........................................................................................1
Unpacking the Kit..................................................................................................................... 1
Other Equipment....................................................................................................................... 3
Preparing the Environment....................................................................................................... 3
Installing the Software.............................................................................................................. 4
Installing the PXIe-4162........................................................................................................... 4
PXIe-4162 Pinout and LEDs.....................................................................................................6
Configuring the PXIe-4162 in MAX...................................................................................... 12
Self-Calibrating the PXIe-4162.............................................................................................. 13
Programming the PXIe-4162.................................................................................................. 14
Troubleshooting...................................................................................................................... 16
What Should I Do if the PXIe-4162 Doesn't Appear in MAX?......................................16
Why Is the ACCESS LED Off When the Chassis Is On?...............................................17
What Should I Do if the PXIe-4162 Fails the Self-Test?................................................17
Where To Go Next.................................................................................................................. 18
Worldwide Support and Services............................................................................................ 18
Verifying the System Requirements
To use the NI-DCPower instrument driver, your system must meet certain requirements.
Refer to the product readme, which is available on the driver software media or online at
ni.com/manuals, for more information about minimum system requirements, recommended
system, and supported application development environments (ADEs).
Unpacking the Kit
Refer to the following figure to identify the contents of the PXIe-4162 kit.

Figure 1. PXIe-4162 Kit Contents
23
11
PXIe-4162
OUTPUT
12-CH PrecisionSMU
ACCESS VOLTAGE
ALLCHANNEL SIGNALS
±24V MAX
60V MAX to
1. PXIe-4162
2. PXIe-4162 Safety, Environmental, and Regulatory Information
3. Maintain Forced-Air Cooling Note to Users
Notice To prevent electrostatic discharge (ESD) from damaging the module,
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the module from the package and inspect it for loose components or other signs
of damage.
Notice Never touch the exposed pins of connectors.
Note Do not install a module if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the module in the antistatic package when the module is not in use.
2| ni.com | PXIe-4162 Getting Started Guide

Other Equipment
There are several required items not included in your PXIe-4162 kit that you need to operate
the PXIe-4162. Your application may require additional items not included in your kit to
install or operate your PXIe-4162.
Required Items
• A PXI Chassis and chassis documentation
• A PXI Controller or PC with a Device for PXI Remote Control system that meets the
system requirements specified in this guide and chassis documentation
Optional Items
• PXI Slot Blocker Kit (NI part number 199198-01)
• SHDB62M-DB62M-LL Low Leakage Cable for SMU, 62 D-Sub Male to 62 D-Sub Male
– 1 m (NI part number 142947B-01)
– 2 m (NI part number 142947B-02)
• SHDB62M-BW-LL Low Leakage Cable for SMU, 62 D-Sub Male to Bare Wire Male
– 1 m (NI part number 142948A-01)
– 2 m (NI part number 142948A-02)
• 62-Pin Connector Kit for PXIe-416x SMUs (NI part number 785582-01)
Visit ni.com for more information about these additional items.
Preparing the Environment
Ensure that the environment you are using the PXIe-4162 in meets the following
specifications:
Temperature and Humidity
Temperature
Operating
Chassis with slot cooling
capacity ≥58 W1
0 °C to 55 °C
All other compatible chassis 0 °C to 40 °C
Storage -40 °C to 71 °C
1Not all chassis with slot cooling capacity ≥58 W can achieve this ambient temperature range. Refer
to PXI chassis specifications to determine the ambient temperature ranges your chassis can achieve.
PXIe-4162 Getting Started Guide | © National Instruments | 3

Humidity
Operating 10% to 90%, noncondensing
Storage 5% to 95%, noncondensing
Pollution Degree 2
Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient temperature)
Notice This model is intended for use in indoor applications only.
Related Information
Refer to the PXIe-4162 Specifications at ni.com for complete specifications.
Installing the Software
You must be an Administrator to install NI software on your computer.
1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.
2. Visit ni.com/downloads/drivers and search for NI-DCPower.
3. Download the latest version of NI-DCPower by clicking Download and then running the
executable (.exe) file.
Driver support for the PXIe-4162 was first available in NI-DCPower 17.6.
4. Follow the instructions in the installation prompts.
Note Windows users may see access and security messages during
installation. Accept the prompts to complete the installation.
5. When the installer completes, select Restart in the dialog box that prompts you to restart,
shut down, or restart later.
Installing the PXIe-4162
Notice To prevent damage to the PXIe-4162 caused by ESD or contamination,
handle the module using the edges or the metal bracket.
The PXIe-4162 is a single-slot module with one backplane connector. The module may be
installed into any PXI Express-compatible slot.
1. Ensure the AC power source is connected to the chassis before installing the PXIe-4162.
The AC power cord grounds the chassis and protects it from electrical damage while you
install the PXIe-4162.
2. Power off the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior to
installation. Do not install a module if the backplane is damaged.
4| ni.com | PXIe-4162 Getting Started Guide

4. Position the chassis so that inlet and outlet vents are not obstructed.
For more information about optimal chassis positioning, refer to the chassis
documentation.
5. Remove the black plastic covers from all the captive screws on the module front panel.
6. Identify a supported slot in the chassis. The following figure shows the symbols that
indicate the slot types.
Figure 2. Chassis Compatibility Symbols
NI PXIe-1062Q
12 3 45
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
PXIe-4162 modules can be placed in PXI Express peripheral slots, PXI Express hybrid
peripheral slots, or PXI Express system timing slots.
7. Touch any metal part of the chassis to discharge static electricity.
8. Ensure that the ejector handle is in the downward (unlatched) position.
9. Place the module edges into the module guides at the top and bottom of the chassis. Slide
the module into the slot until it is fully inserted.
Figure 3. Module Installation
2
3
NI PXIe-1075
1
1. Chassis
2. Hardware Module
3. Ejector Handle in Downward (Unlatched) Position
10. Latch the module in place by pulling up on the ejector handle.
PXIe-4162 Getting Started Guide | © National Instruments | 5

11. Secure the module front panel to the chassis using the front-panel mounting screws.
Note Tightening the top and bottom mounting screws increases mechanical
stability and also electrically connects the front panel to the chassis, which can
improve the signal quality and electromagnetic performance.
12. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize
cooling air flow, depending on your application.
13. Power on the chassis.
Related Information
Why Is the ACCESS LED Off When the Chassis Is On? on page 17
PXIe-4162 Pinout and LEDs
Front Panel
Refer to the following figures and tables for information about the PXIe-4162 front panel
connector pins, channels, and LEDs.
PXIe-4162
OUTPUT
12-CH Precision SMU
ACCESS VOLTAGE
ALL CHANNEL SIGNALS
± 24V MAX
60V MAX to
A
B
6| ni.com | PXIe-4162 Getting Started Guide

Item
A LED Access Status indicator
B LED Voltage Status Indicator
Table 1. LED Access Status Indicator
Status Indicator Device State
(Off) Not Powered
Green Powered
Amber Device is being accessed
Table 2. LED Voltage Status Indicator
Status Indicator Output Channel State
(Off) All device outputs are disconnected from their voltage generation sources
through output disconnect relays.
Green At least one device output is connected to a voltage generation source.
Red The device has a fault or is in error due to the voltage generated or
measured by the device. Refer to the driver software for possible sources.
The device will not operate until the error is cleared and/or the device is
reset.
Pinout
The following figure and table provide detailed signal information for the PXIe-4162
connector.
PXIe-4162 Getting Started Guide | © National Instruments | 7

CH1 Output HI
CH1 Sense HI
CH10 Sense LO
Calibration HI
CH10 Sense HI
CH10 Guard
CH10 Output HI
CH7 Guard
CH7 Sense LO
CH7 Output HI
CH7 Sense HI
CH0 to 11 Output LO
CH4 Guard
CH4 Sense LO
CH4 Output HI
CH4 Sense HI
CH1 Sense LO
CH1 Guard
CH0 Output HI
CH0 Sense HI
CH2 Guard
CH2 Sense LO
CH3 Output HI
CH3 Sense HI
CH5 Guard
CH5 Sense LO
CH6 Output HI
CH6 Sense HI
CH8 Guard
CH8 Sense LO
CH9 Output HI
CH9 Sense HI
CH11 Guard
CH11 Sense LO
CH0 Guard
CH0 Sense LO
NC
CH2 Output HI
CH2 Sense HI
CH3 Guard
CH3 Sense LO
NC
CH5 Output HI
CH5 Sense HI
CH6 Guard
CH6 Sense LO
NC
CH8 Output HI
CH8 Sense HI
CH9 Guard
CH9 Sense LO
NC
CH11 Output HI
CH11 Sense HI
62
61
60
59
56
55
54
57
50
49
48
51
45
44
43
46
20
21
19
18
17
14
13
12
15
8
7
6
9
10
3
2
1
4
42
41
40
39
38
37
36
35
34
33
31
30
29
28
27
26
25
24
23
22
8| ni.com | PXIe-4162 Getting Started Guide

Table 3. PXIe-4162 Signal Descriptions
Bundle Channel Pin Signal Description
A 0 62 Output HI
61 Sense HI
41 Sense LO
42 Guard2
1 20 Output HI
19 Sense HI
17 Sense LO
18 Guard2
2 39 Output HI
38 Sense HI
59 Sense LO
60 Guard2
B 3 57 Output HI
56 Sense HI
36 Sense LO
37 Guard2
4 15 Output HI
14 Sense HI
12 Sense LO
13 Guard2
5 34 Output HI
33 Sense HI
54 Sense LO
55 Guard2
2Guard terminals are not supported in the highest current ranges: 60 mA or 100 mA.
PXIe-4162 Getting Started Guide | © National Instruments | 9

Table 3. PXIe-4162 Signal Descriptions (Continued)
Bundle Channel Pin Signal Description
C 6 51 Output HI
50 Sense HI
30 Sense LO
31 Guard2
7 9 Output HI
8 Sense HI
6 Sense LO
7 Guard2
8 28 Output HI
27 Sense HI
48 Sense LO
49 Guard2
D 9 46 Output HI
45 Sense HI
25 Sense LO
26 Guard2
10 4 Output HI
3 Sense HI
1 Sense LO
2 Guard2
11 23 Output HI
22 Sense HI
43 Sense LO
44 Guard2
A, B, C, D 0 to 11 10 Output LO
10 | ni.com | PXIe-4162 Getting Started Guide