National Instruments TBX-2809 User manual

INSTALLATION INSTRUCTIONS
NI TBX-2809
Screw Terminal Accessory for the NI SwitchBlock
This installation guide describes how to install and connect signals to the NI TBX-2809 screw
terminal accessory for use with NI SwitchBlock cards.
The NI TBX-2809 is an unshielded, DIN-rail mountable terminal breakout block that consists
of a printed circuit board with screw terminals that provide connections to all channels of a
single NI SwitchBlock card. The NI TBX-2809 includes a safety interlock resistor to engage the
NI SwitchBlock card’s safety relays, allowing connections to the NI SwitchBlock analog bus.
Specifications
Maximum voltage............................................. 150 V, CAT I
Maximum current ............................................. 1 A
Caution The maximum voltage is limited to the lowest voltage of any component in
the NI SwitchBlock system. Review the specifications of the NI SwitchBlock carrier
and cards.
Caution The NI TBX-2809 must be installed inside a suitably rated enclosure with
proper cable/wire strain relief(s) prior to use. There are no user serviceable parts
inside. Do not change or alter this product in any way.
Caution NI products typically must be operated with shielded cables and accessories
to ensure compliance with Electromagnetic Compatibility (EMC) requirements. To
determine if shielded cables or accessories are required for the product that the
NI TBX-2809 will be used with, refer to the EMC specifications in the product’s user
guide or manual. If shielded cables or accessories are required for EMC compliance,
do not use unshielded cables or accessories unless they are installed in a shielded
enclosure with properly designed and shielded input/output ports, and are connected
to the NI product using a shielded cable. If unshielded cables or accessories are not
properly installed and shielded, the EMC specifications for the product are no longer
guaranteed.
Compatible DIN rails........................................ DIN EN 50 022
DIN EN 50 035
Ρ΅νιϋΠȂ඾ུࢊβȜΐ܄ȃ

NI TBX-2809 Installation Instructions 2 ni.com
Dimensions (L ×W ×H) ..................................12.5 ×12.8 ×8.5 cm
(4.9 ×5.0 ×3.4 in.)
Weight ...............................................................264 g (9.3 oz)
What You Need to Get Started
You need the following items to set up and use your screw terminal accessory:
❑One NI SwitchBlock card
❑NI TBX-2809 screw terminal accessory
❑One of the following NI SwitchBlock cable assemblies:
– SH96F-96M-NI SwitchBlock cable
– SH96F-96M-RES-NI SwitchBlock cable
❑1/10 in. (2.5 mm) flathead screwdriver
❑#1 Phillips-head screwdriver
❑Wire cutters
❑Wire insulation strippers
Signal Connection
Refer to Figure 1 and perform the following steps to connect your signals to your screw terminal
accessory:
1. Unscrew the four cover screws with a Phillips-head screwdriver to remove the cover.
2. Use wire cutters and wire insulation strippers to strip the wire ends as necessary to connect
them to screw terminals.
3. Loosen the screws in the screw terminals with a 1/10 in. (2.5 mm) flathead screwdriver.
4. Insert the stripped wires into the screw terminals, and tighten the screws with a 1/10 in.
(2.5 mm) flathead screwdriver.
5. Allow the signal wires to exit through the cover opening.
Note The NI TBX-2809 screw terminal accessory does not provide strain relief for
signal wires. Add strain relief and insulation for your signal wires, if necessary.
6. Replace the cover and tighten the cover screws.
7. If using a shielded cable, connect the cable shield to the earth ground terminal.

©National Instruments Corporation 3 NI TBX-2809 Installation Instructions
Figure 1. NI TBX-2809 Parts Locator Diagram
Installing Your Screw Terminal Accessory
Refer to Figure 2 and perform the following steps to connect the screw terminal accessory to the
NI SwitchBlock card connector:
1. Securely fasten the connector on one end of the cable to the NI SwitchBlock card connector
using the thumbscrews.
2. Securely fasten the connector on the other end of the cable to the screw terminal accessory
connector using the thumbscrews.
To disconnect the cable, unscrew the cable and gently pull on the backshell. Do not pull the
cable.
Caution The connectors of both the NI SwitchBlock card and the cable are
polarized. You can attach them in only one way. Tie the ground terminal to an earth
ground to ground the screw terminal end of the cable shield. Do not force the cable
when inserting it into or removing it from the NI SwitchBlock card connector.
1CoverScrews
2 Cover
3 Cover Opening
4 Screw Terminals
5 Signal Wires
6 Ground terminal
2
16
4
5
3

NI TBX-2809 Installation Instructions 4 ni.com
Figure 2. Connecting the Cable Assembly
1 NI SwitchBlock Card
2 Thumbscrews
3 SH96F-96M-NI SwitchBlock Cable
4 Cable Connectors
5 Ground terminal
6 NI TBX-2809
7 Signal Wires
2
3
7
4
1
5
6

©National Instruments Corporation 5 NI TBX-2809 Installation Instructions
Refer to Figure 3 for NI TBX-2809 pinouts.
Figure 3. NI TBX-2809 Pinouts
Mounting the NI TBX-2809
When you have completed signal connections and terminal block installation, you can directly
mount the NI TBX-2809 assembly onto a DIN rail with a firm push.
To unmount the NI TBX-2809 from the DIN rail, place a flathead screwdriver into the slot above
the terminal block base and pry it away from the rail.
Compliance and Certifications
Safety
This product is UL Recognized as a component and meets the requirements of the following
standards of safety for electrical equipment for measurement, control, and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA 61010-1
Note For UL and other safety certifications, refer to the product label or the Online
Product Certification section.
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for electrical equipment
for measurement, control, and laboratory use:
• EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity
• EN 55011 (CISPR 11): Group 1, Class A emissions
NC
NC
93
45
92
91
44
43
90
89
42
41
88
87
1
2
49
50
3
4
51
52
5
6
53
54
7
8
32
31
78
77
30
29
76
75
28
27
74
73
26
25
72
71
36
35
82
81
34
33
80
79
40
39
86
85
38
37
84
83
55
56
9
10
57
58
11
12
59
60
13
14
61
62
15
16
67
68
21
22
69
70
23
24
63
64
17
18
65
66
19
20

NI TBX-2809 Installation Instructions 6 ni.com
• AS/NZS CISPR 11: Group 1, Class A emissions
• FCC 47 CFR Part 15B: Class A emissions
• ICES-001: Class A emissions
Caution When operating this product, use shielded cables measuring less than
3 meters and shielded accessories.
Note For EMC declarations and certifications, refer to the Online Product
Certification section.
CE Compliance
This product meets the essential requirements of applicable European Directives as follows:
• 2006/95/EC; Low-Voltage Directive (safety)
• 2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Online Product Certification
To obtain product certifications for this product, visit ni.com/certification, search by
model number or product line, and click the appropriate link in the Certification column.
Environmental Management
NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.
For additional environmental information, refer to the NI and the Environment Web page at
ni.com/environment. This page contains the environmental regulations and directives with
which NI complies, as well as other environmental information not included in this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products must be sent to a
WEEE recycling center. For more information about WEEE recycling centers,
National Instruments WEEE initiatives, and compliance with WEEE Directive
2002/96/EC on Waste Electrical and Electronic Equipment, visit
ni.com/environment/weee.
⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑
RoHS
˅
Ё೑ᅶ᠋
National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ
(RoHS)DŽ݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/
environment/rohs_chinaDŽ(For information about China RoHS compliance,
go to ni.com/environment/rohs_china.)

© 2010–2011 National Instruments Corporation. All rights reserved.
375532C Aug11
LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments
Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks. Other product and
company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments
products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National
Instruments Patents Notice at ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/export-compliance
for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data.