NAUTICA 2039 User manual

CONGRATULATIONS ON OWNING YOUR NEW NAUTICA WATCH
DEVELOPED FROM ADVANCED ELECTRONICS TECHNOLOGY,
THE MOVEMENT IS MANUFACTURED FROM THE BEST QUALITY
COMPONENTS AND POWERED BY A LONG LIFE BATTERY.

1
PAGE
WATCH INFORMATION AND CARE 2 - 5
OPERATING INSTRUCTIONS
BASIC MODELS 6 - 7
DATE MODELS 8 - 9
MULTI MODELS 10 - 13
INDIGLO MODELS 14 - 15
CHRONOGRAPH MODELS 16 - 52
ANALOG & DIGITAL MODELS 53 - 62
DIGITAL MODELS 63 - 66
SPECIAL MODELS
TIDE 67 - 69
WORLD TIME 70 - 73
HIGH PERFORMANCE MODELS
TIDE, TEMPERATURE & COMPASS 74 - 79
SOLAR 80 - 81
DEPTH 82 - 85

22
NAUTICA watches have been developed with the highest attention to
quality, function and detail, as bets the NAUTICA tradition. Please read
the following instructions carefully to fully understand all of the functions of
your nely crafted timepiece.
WATER-RESISTANCE
If your watch is water-resistant, it will be indicated on the watch face
or on the caseback.
• 50 Meter Water-Resistant watch withstands water pressure to 86p.s.i.a.
(equals immersion to 164 feet or 50 meters below sea level) and dust as
long as crystal, crown and case remain intact.
• 100 Meter Water-Resistant watch withstands water pressure to
160p.s.i.a. (equals immersion to 328 feet or 100 meters below sea
level) and dust as long as crystal, crown and case remain intact.
• 200 Meter Water-Resistant watch withstands water pressure to
320p.s.i.a. (equals immersion to 656 feet or 200 meters below sea
level) and dust as long as crystal, crown and case remain intact.
NOTE: CROWN MUST BE SCREWED INTO THE CASE
PROTRUSION TO ASSURE WATER RESISTANCE.
WATCH IS NOT AN ISO 6425 CERTIFIED DIVE WATCH.

33
INDIGLO® NIGHT-LIGHT
If your watch has “INDIGLO” on the dial, your watch is equipped with
the INDIGLO Night-Light. To activate this feature, depress the crown or
the pusher on the left side of the watch to illuminate the entire dial for
easy reading during nighttime or low light conditions. Light will appear
immediately.
Your NAUTICA watch featuring INDIGLO Night-Light contains a
patented electroluminescent technology (U.S. Patent Number 4,527,96
and 4,775,964). The INDIGLO Night-Light illuminates the entire watch
lens with a uniform bright light that offers superior readability in all low
light and nighttime conditions. Simply press the appropriate button to
activate.
WARNING: DO NOT PRESS THE BUTTON UNDER WATER AS THE
WATCH WILL NOT RETAIN WATER RESISTANCE
INDIGLO is a registered trademark of Indiglo Corporation.
BATTERY
Please recycle or dispose of battery properly. Do not dispose of battery
in the re. Do not recharge battery. Keep loose batteries away from
children.

SCREW-IN SETTING CROWN
Some deep-depth water-resistant watches require the setting crown to
be screwed in to ensure water-resistancy. If your Nautica watch has
a transparent sticker at back of the case back (diagram above)
please unscrew the crown before setting your watch, and the
crown must be screwed in after setting the watch.
To screw in, push in the crown rmly against the thread protrusion
and hold it in while turning the crown clockwise. Continue to screw in
the crown light until it is tight .
ATTENTION
This is a screw down crown
Do not pull
Please read instruction
booklet before operation
SCREW-IN SETTING CROWN STICKER
4

ELAPSED TIME RING
If your watch is equipped with a rotating outer dial with numbers and
indicators, this Elapsed Time Ring may be used to indicate the length
of time remaining for an activity or the starting time of an activity.
TIME REMAINING - set the outer ring so that the triangle is pointing
to the time the activity is to end.
STARTING TIME - set the triangle on the time the activity is to begin.
TACHYMETER
A tachymeter measures the speed at which the wearer has traveled
over a measured distance, i.e., a measured mile on the highway. For
example, start the chronograph when you pass the starting point and
stop it when you pass the nish point. You can then read your speed
in units per hour off the tachymeter scale.
BAND ADJUSTMENT
To disconnect band from clasp, press in end of spring bar
(use pin or small paper clip) and separate link band from
clasp as illustrated.
To reassemble band to clasp, place spring bar in band and place end
of spring bar into desired hole in clasp. Press opposite end of spring
bar in and slide into clasp and position so tip snaps into corresponding
hole.
5

6
CROWN POSITION
A B
CROWN POSITION
A B
BASIC MODELS
Y121, 2039, 2036, 608/1010 VX10 / VX51 / YL60 / 4S20
336/168
CROWN
POSITION
A B

7
TIME
To set the time:
1. Pull crown to “B” position.
2. Turn crown clockwise /counter clockwise to correct time.
3. Push crown to “A” position.

88
DATE MODELS
CROWN POSITION
DATE
A B C
VX33
CROWN POSITION
DAY
DATE
A B C
VX12 / VX42 / VX32 / VX82 / 2315 / 2115 / 2415 / AL32

9
TIME
To set the time:
1. Pull out crown to “C” position.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push in crown to “A” position.
CALENDAR
To set the calendar/date:
1. Pull out crown to “B” position.
2A. Turn crown clockwise / counter clockwise to correct date.
2B. Turn crown counter clockwise to correct date. (For VX33 only)
3. Push in crown to “A” position.
NOTE: The date changes automatically every 24 hours.

10
24 HOUR CROWN
POSITION
A B C
VX3R
DATE
DATE
24 HOUR
VX3J
CROWN
POSITION
A B C
DAY
DAY
DAY
DATE
24 HOUR
CROWN
POSITION
A B C
VX3L
24 HOUR
DAY
CROWN
POSITION
A B C
VX3N / VX7N
DATE
DAY
CROWN
POSITION
A B C
VD79
DATE
VX36
CROWN
POSITION
A B C
DATE
MULTI MODELS

11
TIME
To set the time:
1. Pull crown to “C” position.
2. Turn crown either way to correct time.
3. Push crown to “A” position.
DATE
To set the date:
Note: the date changes automatically every 24 hours.
1. Pull crown to “B” position.
2. Turn crown to correct date.
3. Push crown to “A” position.
DAY OF WEEK (for VX3J / VX3L / VX3N / VX36 / VX7N / VD79)
To set the day:
1. Pull crown to "C" position.
2. Advance time 24 hours to change the day.
3. Push crown to "A" position.
Note: 24 hour indicator can be changed only when setting the time.

12
6P27
DAY
DATE
24 HOUR
CROWN POSITION
6P23
DATE
24 HOUR
24 HOUR
A B C
CROWN POSITION
CROWN POSITION
6P29
DAY
A B C
DATE

13
TIME
To set the time:
1. Pull crown to “C” position.
2. Turn crown either way to correct time.
3. Push crown to “A” position.
DATE
To set the date :
1. Pull crown to “B” position.
2. Turn crown counter clockwise to correct date.
3. Push crown to “A” position.
Note: The day changes automatically every 24 hours.
DAY OF WEEK (for 6P27 / 6P29)
To set the day:
1. Pull crown to “C” position.
2. Turn crown clockwise (hour hands rotate 24 hours) to correct day
of week.
3. Push crown to “A” position.
Note: The day of week changes automatically every 24 hours.

14
To activate the Indiglo:
Press crown to indicate Indiglo night light.
TIME
To set the time:
1. Pull crown to "C" position.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to "A" position.
CROWN POSITION
DATE
A B C
M905
INDIGLO MODELS

15
CALENDAR
To set the date:
1. Pull crown to "B" position.
2. Turn crown counter clockwise or towards you to correct date.
3. Push crown to "A" position.
Note: The date changes automatically every 24 hours.

16
STOPWATCH MINUTES HAND
STOPWATCH HOUR HAND
SMALL SECOND HAND
PUSHER “A”
STOPWATCH 1/20SEC. HAND
STOPWATCH SECOND HAND
YM92
CROWN POSITION
A B C
PUSHER “A”
PUSHER “B”
YM91
STOPWATCH
MINUTE HAND
SECOND HAND
CHRONOGRAPH HAND
1/5 SECOND
CHRONOGRAPH MODELS
A B C
CROWN POSITION
PUSHER “B”
PUSHER “A”
DATE
YM12 / YM1G
PERMANENT
SECOND HAND
STOPWATCH
SECOND HAND
MINUTE HAND
STOPWATCH
MINUTE HAND

17
This Chronograph watch has three functions:
TIME, CALENDAR, STOPWATCH
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
STOPWATCH
This stopwatch is capable of measuring:
– 1/5 second elapsed up to 60 minutes.
– After 60 minutes, it will start counting again from “0” repeatedly up
to 12 hours.