NavAtlas NA2BT Operating instructions

INSTALLATION/OWNER'S MANUAL
Switch Type Digital Bluetooth Controller
NA2BT

2
NA2BT
Mount the controller and AUX/USB in any open switch hole on your dash, be sure to
fully insert until they lock into place.
Please secure the NA2BT module via screw or ties so that the box does not move
around in the dash.
When connecting the dash switch control and AUX port to the box, please make sure
that the plugs are straight and the locking nut is hand tightend securely. DO NOT
OVERTIGHTEN OR DAMAGE THE THREADS IF NOT ALLIGNED PROPERLY.
CONTROLLER MOUNTING

3
NA2BT
UNIVERSAL INSTALLATION
RED - 12V+ACC
BLACK - CHASSIS GROUND
BLUE - OPTIONAL LED CONTROL
POWER
RED RCA - ANALOG RIGHT
WHITE RCA - ANALOG LEFT
GREY RCA- DIGITAL CO-AXIAL OUTPUT
AUDIO
AFTERMARKET SYSTEM
UNIVERSAL CABLE
L
R
Digital out
8 pin waterproof DIN connector
LED ON/OFF
WHEN USING AFTERMARKET AMPLIFIERS WITH SOUNDBARS, YOU MUST USE ANALOG
CABLES FOR DASIY CHAIN FUNCTION TO WORK, A2A CABLE(SOLD SEPARATELY) IS
REQUIRED FOR ANALOG AUDIO OUTPUT TO WORK IN THIS SETUP.
ANALOG INSTALLATION W/AFTERMARKET AMPS
10 Feet (10GA)
2 pin waterproof DIN connector
8 pin waterproof DIN connecto
r
10 Feet (18GA) for
Soundbar 8 pin waterproof
DIN connector
Ground(-)
NS14A/27A/35A
UNIVERSAL CABLE TO AFTERMARKET AMPLIFIER
(BASS AMP, ECT...)
*DIGITAL OUT NOT
USED
Digita R L
l
LED ON /OFF
A2A CABLE
NA1BT/NA2BT/NA30C
NA81MDVR
12V +

4
NA2BT
*OPTIONAL ACCESSORIES ARE D2Y AND D2D CABLES (SOLD SEPARATELY)
EXAMPLE OF DAISY CHAIN DIGITAL CONFIGURATIONS FOR
ANY VEHICLE
OUTPUT CAN CONNECT TO ANY MODEL
(NS14A/27A/35A, NT650AT, BMA500M, ECT...)
10 Feet (10GA)
2 pin waterproof DIN connector
8 pin waterproof DIN connector
8 pin waterproof
DIN connector
Ground(-)
4 pin waterproof DIN connector
4 inch(18ga)
Ground(-)
10 Feet (12GA)
NS14A/27A/35A
NT65AT
8 pin waterproof DIN connector
A2A CABLE
NT308W
BMA500M
Ground(-)
D2D CABLE
CONNECTING CABLE
CONNECTING CABLE
10 Feet (18GA) for soundbar
Y ADAPTER CABLE
D2D CABLE
D2D CABLE
NA1BT/NA2BT/NA30C
NA81MDVR
12V +
12V +
12V +

5
NA2BT
*
GETTING STARTED
1
2
3LED LIGHT ON/OFF
POWER ON
EQ MODES: FLAT - LOW - MID - HIGH
4
5
6
VOLUME UP
PLAY/PAUSE/MUTE
VOLUME DOWN
PREVIOUS TRACK
7
8
9
AUX INPUT/USB CHARGING
NEXT TRACK
8
7
4
23
9
USB 1A
CHARGING
NOT FOR AUDIO PLAYBACK
OPEN
NOTE: TO AVOID WATER
DAMAGE, PLEASE KEEP
AUX/USB COVER CLOSED
WHEN NOT IN USE.
1
5
6
GETTING STARTED
1
2
3LED LIGHT ON/OFF
POWER ON
EQ MODES: FLAT - LOW - MID - HIGH
4
5
6
VOLUME UP
PLAY/PAUSE/MUTE
VOLUME DOWN
PREVIOUS TRACK
7
8
9
AUX INPUT/USB CHARGING
NEXT TRACK
8
7
4
23
9
USB 1A
CHARGING
NOT FOR AUDIO PLAYBACK
OPEN
NOTE: TO AVOID WATER
DAMAGE, PLEASE KEEP
AUX/USB COVER CLOSED
WHEN NOT IN USE.
1
5
6
*NOTE: WHEN USING EQ MODES, SOME MUSIC CAN DISTORT AT MAX VOLUME
ON CERTAIN PHONES/DEVICES
4 1
5
6
8 9
2 3
7
VOLUME UP (SHORT PRESS)
VOLUME DOWN (SHORT PRESS)
AUX INPUT/USB CHARGING
PREVIOUS TRACK (LONG PRESS)
NEXT TRACK (LONG PRESS)
7
8
9

6
NA2BT
1
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTIO
N
1) Power on the CONTROLLER by short-pressing the 1Power button
NOTE: You have 2 minutes before you must restart this procedure over again.
2) The CONTROLLER is now in pairing mode:
ANDROID users:
a. Go into the Settings Menu of your device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth and press SCAN
d.“NA1BT ” will now be displayed under AVAILABLE DEVICES
iOS users:
a. Go into the Settings Menu of your iOS device
b. Enter the Bluetooth Menu
c. TURN ON Bluetooth
d.“NA1BT” will now be displayed
3) If NA1BT is not seen, repeat the above steps to refresh the “Device List”
4) When the connection is successful a tone will be heard, and the Bluetooth LED
indicator will light solid, you are now ready to stream music from your player to the
CONTROLLER
BLUETOOTH OPERATION
"NA2BT"
"NA2BT"
"NA2BT"
1

7
NA2BT
RECONNECTION
1) Power on the
CONTROLLER and your last paired device Bluetooth.
2) Ensure you are within range of the
reconnect
CONTROLLER , the unit will now automatically
3) If the device is out of range from the
CONTROLLER , it will disconnect automatically:
a
. The
range
CONTROLLER will reconnect automatically to your device when in
4) If your device was previously paired with the
paired device:
CONTROLLER , but it wasn’t the last
a. Ensure no other devices are currently paired
b. Enter the Bluetooth Menu on your device being paired
c. “NA1BT”will display under AVAILABLE DEVICES
d. Choose the “NA1BT”to reconnect
4) Long press
EQ button 3~6 seconds, reset paired device list.
5) Long press
PLAY/PAUSE button 3~6 seconds, enter pairing mode .
NOTE:
Some devices may require a manual Bluetooth
reconnection once the devices
Bluetooth
is powered
OFF / ON
and/or back in range
BLUETOOTH OPERATION
2
4
2
4
"NA2BT"
"NA2BT"
4
2

8
NA2BT
NOTE: Bluetooth HD Streaming available on devices/phones that support
Tips
3
2
1
5
4
BLUETOOTH OPERATIO
N
1) Press the 1PLAY/PAUSE once to start playing music or press the PLAY
button from your devices touch screen
2) To skip songs or advance, press the 2NEXT TRACK button
3) To select the previous song, press the 3PREVIOUS TRACK button
VOLUME CONTROL
4) To raise the volume press the 4VOLUME UP button or use your devices controls
5) To lower the volume press the
controls
5VOLUME DOWN button or use your devices
NOTE: Some devices use an independent volume control, for most devices the
volume control on the controller will adjust the phone volume, in other cases you will
need to raise the phone volume to max in order hear the music clearly.
WARNING: DO NOT USE AUX AND BLUETOOTH AT THE SAME TIME.
Make sure your device Bluetooth volume is set at 100% level
before stowing your device
STREAMING MUSIC
BLUETOOTH OPERATION
1) Press the 1PLAY/PAUSE once to start playing music or press the PLAY
button from your devices touch screen
2) To skip songs or advance, press the 2
2
3) To select the previous song, press the 3
3
VOLUME CONTROL
4) To raise the volume press the VOLUME UP button or use your devices controls
5) To lower the volume press the
controls
VOLUME DOWN button or use your devices
NOTE: Some devices use an independent volume control, for most devices the
volume control on the controller will adjust the phone volume, in other cases you will
need to raise the phone volume to max in order hear the music clearly.
WARNING: DO NOT USE AUX AND BLUETOOTH AT THE SAME TIME.
this function/codec
*NOTE:
1
32
NEXT TRACK button (PRESS FOR 3 SEC)
PREVIOUS TRACK button
(PRESS FOR 3 SEC)

9
NA2BT
YOU CAN PLAY AUDIO
FROM ANY DEVICE
THAT HAS A 3.5MM
HEADPHONE JACK
CONTROLLER AUX-IN OPERATION
1) Power on the
button for 3 seconds
CONTROLLER by pressing and holding down the 1POWER
2) Disconnect any paired Bluetooth Bluetooth in your
devices Settings Menu
3) Connect your 3.5mm AUX-IN cable located on front side of the CONTROLLER
to your devices headphone jack
VOLUME CONTROL
To raise the volume press the 2
To lower the volume press the 3
AUX-INPUT
NOTE: When on AUX Mode, EQ Fuctions will not Work, Audio Settings will Need to be
adjusted From The Phone or Device
4)
5)

10
NA2BT
is device complies with part 15 of the FCC Rules. Operation is subject to
the condition that this device does not cause harmful interference (1) this
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Changes or modications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: is equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. ese limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
e device has been evaluated to meet general RF exposure requirement. e
device can be used in portable exposure condition without restriction.
FCC Compliance

11
NA2BT

Support Line: 1-562-946-7471
9AM-5PM PST Monday-Friday
www.navatlas.com
All rights reserved.
NSA0119-V01
Printed in China