Navig8r DRONE-WF20 User manual

USER MANUAL DRONE-WF20
To help get you started, please refer to the quick connection guide below
Action Drone Indicator Remote Indicator
1 Turn on Drone Fast then slow flash -
2 Turn on Remote Slow flash Slow RED flash
Connection (Throttle up then down beforebegin)
3 Connection successful Solid light RED light off
4 Press launch / land button, then throttle up to take off
5 Press the launch / land button / throttle down to land
Note:
Drone Double flashes Drone not paired
Drone Fast flashes Flat battery / Cannot connect

USER MANUAL DRONE-WF20
SAFETY PRECAUTIONS
Keep the battery away from heat sources such as fire and sun
Store the battery in a cool dry place
When recharging, only use the battery charger intended for that purpose
Don’t over-charge the battery
Don’t charge the battery for more than two hours
Don’t leave a charging battery unattended
Please read through the manual before use and store for later reference.
Please store small parts in a place well out of the reach of small children
Keep all body parts away from the drone while the rotor blades are spinning
Never try to repair internal circuitry. This product has no serviceable parts
Keep small parts out of reach of children as they can be a choking hazard.
Do not rush your flight. Always stay in control.
After flight, turn the DRONE off first, then turn the controller off.
Do not fly your Drone in prohibited areas, such as near airports or near/above people
Children should operate a drone only with adult supervision
Always keep sight of your drone while flying and resist the urge tofly too high
Always turnthe power offon thecontroller and DRONEwhen not in use.
BATTERY PROTECTION
This DRONE is equipped with low-voltage protection. When a battery is low on charge, the programmed
control system will stop the DRONE’s rotors. The battery will then need re-charging before use
MAINTENANCE
Clean the DRONE with a clean, dry soft cloth only. To avoid irreparable damage, keep the DRONE dry
and away from watersuchas rain. Check theDRONE and accessories for damage before flight. If
damage is found, do not use the DRONE until it is repaired.
REMOTE CONTROL BATTERY INSTALLATION
Remove the battery cover screw using the
supplied screwdriver. Remove the battery
cover and insert 4 X 1.5V AAA batteries,
according to indicated polarity (batteries
not included). Reattach the cover and
tighten the screw.
Note: Battery installation should be done
under adult supervision. Do not mix old and new batteries inside the controller.

USER MANUAL DRONE-WF20
CHARGING YOUR DRONE BATTERY
Connect your drone battery to a USB charger, such as a PC, using the supplied USB cable. You can also
remove the battery from the drone for charging. (See details below.)
Note: The battery isfully charged once theGREEN status indicator on the battery turns off.
HOW TO REMOVE THE BATTERY FROM THE DRONE
Depress both top and bottom locking latches together and carefully slide the
battery out.

USER MANUAL DRONE-WF20
REMOTE CONTROL
No.
Function
Description
1
Power
Indicator
Illuminates when power is turned on
2
Connection
indicator Flashes RED during the connection process. Turns off when connected.
Camera Indicator
(Not available on
this model)
The light will blink once while taking picture and remain onwhile recording
video (Not available on this model)
3
Take picture
/
record video
(Not available on
this model)
Press one timefor taking picture, press for 3 seconds for recordingvideo
(Not available on this model)
4 Flip
P
ush
the control stick in
(
as opposed to up or down). A
repeating
BEEP will
then sound alerting you that you are in FLIP mode. Then, use the right control
stick to flip the drone in the selected direction.Once the flip is complete, the
BEEP sound will stop. Repeat this process for multiple flips.
5
Right Stick
D
rive
the drone forwards, backwards, left or right
6
Trim button
(See explanation below)
7
Trim button
(See explanation below)
8 Headless mode
Press once
to select
headless mode
. Press
again to
exit
headless
mode.
Note: Headless mode will always drive thedrone forwards, no matter which
way the front of the drone is facing.
9 One key return
function
Drives the drone back toits
original start
area
(manua
l landing then required)
Note: The DRONE and user must stay in the same orientation from each
other, in order for this function to operate correctly.
10
Trim button
(See explanations below)
11
Left Stick
Move up and down to control speed and side to
side to rotate
12 Speed Select
Press
in (as opposed to up or down) There are 3 different speeds; slow,
medium and fast. These are indicated by one, two or three BEEPs)
13 Unlock / Take off /
Land / Emergency
Press once to unlock the drone andto start the rotors for take-off.
Press after your flight, to land the drone.
Note: Duringflightpressand hold for 5seconds for an emergency stop.
2
3
4
5
6
7
1
13
12
11
10
9 8

USER MANUAL DRONE-WF20
SIMPLE OPERATING STEPS
BASIC OPERATION CONTROLS
Note: When the drone is flying towards you, the control directions are reversed.
Check the left stick is in
the center position.
Turn on the controller
by
sliding the power button
across
Turn on the DRONE. (The
LED light on the drone will
flash rapidly
then, slowly
)
Place the DRONE
on a level position.
Slowly p
ush the
left stick
up
then
down. A double beep will sound
(when successful). The LED light on
the drone will then remain on. The
DRONE is ready to fly.
Press the start
button
to start flying. Press
again after your flight
to begin your landing.

USER MANUAL DRONE-WF20
AUTO TRIM FUNCTION
Press both control sticks down and left to 45 degree circle (image
right) for 10 second. The indicators on the drone will begin to
flash rapidly. When complete, the indicators will then stop flashing.
MANUAL TRIM FUNCTION
From time to time your drone can
benefit from a trim adjustment. Trim
adjustment can be used to keep your
drone hovering in the same place,
which is especially useful while taking
photos or manoeuvring in tight
places.
Forward
/
B
ackward
Trim
Left / Right
rotation Trim Left / Right
side Trim

USER MANUAL DRONE-WF20
MANUAL TRIM EXPLAINED

USER MANUAL DRONE-WF20
TRICKS: FLIPS & ROLLS
Press the right stick in once (as opposed to up or down) A continuous beep will then sound. Then move
the right stick again in the direction you wish the drone to flip (Left, right, forwards or backwards)
Note: Before you perform a flip trick, always make sure you have enough space both above and below
your DRONE.
ONE KEY RETURN FUNCTION
Press the button as depicted (right) for one key return. You
can move the control stick in any direction to cancel this
command.
Note: When the drone isfirst turned on and the LED
indicators stop flashing, this is when the drone sets the
forward facing side as the front of the drone. If the drone
isn’t pointing the right way at take off, it will not be able to
effectively return to the start area. If you want to reset the
front direction, you need to turn your Drone off then on again
to reset.
HEADLESS FUNCTION
In headless mode, the drone will always fly forward if flown
forward (and in any other direction) regardless of whichway
the drone is facing. Essentially, this features removes the
drone’s awareness of orientation when it has been rotated.
To enter this mode, press the controller button as depicted
(right). A beep will continuously sound as a reminder. You are
then thenin headless flying mode. To quitthis mode, just press
the same button again. A beep will sound as confirmation.
Press the right stickin, and then steerto
the left
Press the ri
ght stickin, and then steer to
the
right
Press the right stickin, and then steerto
the
front
Press the right stickin, and then steerto
the
rear

USER MANUAL DRONE-WF20
APP DOWNLOAD AND INSTALLATION
Visit the App Store (for Apple devices) or Google
Play (for Android Devices).
Search for and install “NAVIG[8]R WD” or
“HELICUTE 720P FPV”
CONNECTING YOUR DRONE
Ensure you have a Wi-Fi connection on your smart device and that it is turned on.
Find the Wi-fi network called “NAVIG[8]R WD” or “HELICUTE 720P FPV”
Click the connect button
Open your App and press the “Play” icon
The control panel will then display as the screen shots below.
A streaming image will then finally appear on screen.
REPLACING DAMAGED BLADES
Your drone will come with 4 replacement propellers, two
type “A” and two type “B”. Use the supplied screwdriver
to remove the rotars. Attached the new propeller then,
tighten back down the screws.
Note: "A" and "B" will be mark on your drone, next to the
propellers.
SPECIFICATIONS
Battery requirements for remote: 4 X 1.5V “AAA” size batteries (not included)

USER MANUAL DRONE-WF20

USER MANUAL DRONE-WF20

USER MANUAL DRONE-WF20
NOTA
V
AILABLE ON THIS MODEL
TAKE PICTURE / RECORD VIDEO
NOT AVAILABLE ON
THIS MODEL