NCR 7360-K051 Manual

Kit Instructions
Security Door Electronic Lock
7360-K051
Issue A

ii
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCR FastLane SelfServ™ Checkout is a trademark of NCR Corporation in the
United States and/or other countries. Other product names mentioned in this publication may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms
and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR
office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book.
Please use the link below to send your comments.
EMail: [e-mail]
Copyright © 2020
By NCR Corporation
864 Spring St. NW
Atlanta, GA 30308
United States
All Rights Reserved

iii
Revision Record
Issue Date Remarks
ASep 2020 First Issue

Security Door Electronic Lock (La Gard)
The Security Door Electronic Lock limits the access to the currency devices. This
publication provides procedures for installing an Electronic Lock (La Gard) on the
Security Door of an NCRFastLane SelfServ™ Checkout (7360) unit.
Kit Contents
Part Number Description
497-0528448 7360-K051 Kit - La Gard Electronic Lock
006-8627089 Safe Basic Electronic Lock, La Gard
* 497-0423108 Instructions-Kit (Reference Sheet)
* Items marked with an asterisk are not called out on the image.

2 7360-K051 Security Door Electronic Combination Lock
Installation Procedure
To install the Electronic Lock (La Gard), do the following procedures:
1. Remove the existing Security Door Lock. Depending on the type of Lock, refer to
either of the following procedures:
•Removing Electronic Lock on the facing page.
•Removing Keylock on page6.
2. Install the Electronic Lock (La Gard). For more information, refer to Installing
Electronic Lock on page8.
Note: To replace the Electronic Lock Battery, refer to Replacing ElectronicLock Battery on
page18.

7360-K051 Security Door Electronic Combination Lock 3
Removing Electronic Lock
To remove the Electronic Lock, follow these steps:
1. Open the Electronic Lock. For more information, refer to Opening Electronic Lock on
page14.
2. Remove the Lock Assembly by doing the following:
a. Detach the Lock Assembly from the Security Door by removing three (3) bolts, as
shown in the image below.

4 7360-K051 Security Door Electronic Combination Lock
b. Disconnect the cable from the connector port of the Lock Assembly and then
remove the excess cable secured on the bridge lance, as shown in the image
below.
3. Rotate the Entry Device Assembly at approximately 30° counterclockwise to
disengage it from the Dial Plate, as shown in the image below.

7360-K051 Security Door Electronic Combination Lock 5
4. Detach the Dial Plate from the Security Door by removing two (2) screws, as shown
in the image below.

6 7360-K051 Security Door Electronic Combination Lock
Removing Keylock
To remove the Keylock, follow these steps:
1. Open the Keylock. For more information, refer to Opening Keylock on page16.
2. Detach the Escutcheon Cover from the Security Door by removing two (2) mounting
screws, as shown in the image below.

7360-K051 Security Door Electronic Combination Lock 7
3. Detach the Lock Assembly from the Security Door by removing three (3) bolts, as
shown in the image below.

8 7360-K051 Security Door Electronic Combination Lock
Installing Electronic Lock
To install the Electronic Lock, follow these steps:
1. Remove the existing Electronic Lock, if necessary. Depending on the type of Lock,
refer to either of the following procedures:
•Removing Electronic Lock on page3.
•Removing Keylock on page6.
2. Align the Dial Plate to the Spindle hole of the Security Door and then secure it using
two (2) screws, as shown in the image below.
Note: Ensure that the Dial Plate is in its proper orientation with the UP labels
pointing upwards.

7360-K051 Security Door Electronic Combination Lock 9
3. Assemble the Entry Device Assembly by doing the following:
a. Insert the Spindle into the Entry Device and ensure that it is fully seated in the
slot.
b. Route the Entry Device cable in the groove of the Spindle, as shown in the image
below.

10 7360-K051 Security Door Electronic Combination Lock
c. Slide the Bearing Plate over the cable and spindle and then press onto the
fasteners of the Entry Device.
4. Feed the Entry Device Assembly cable through the Spindle hole, as shown in the
image below.

7360-K051 Security Door Electronic Combination Lock 11
5. Secure the Entry Device Assembly to the Dial Plate on Security Door by doing the
following:
a. Rotate the Entry Device approximately 30° counterclockwise to engage its
bushings into the large openings of the Dial Plate, as shown in the image below.
b. Turn the Entry Device clockwise until it is in vertical orientation.

12 7360-K051 Security Door Electronic Combination Lock
6. Install the Lock Assembly by doing the following:
a. At the back of the Security Door, pull the cable gently to ensure that there is no
excess cable in the Spindle hole.
b. Connect the cable to the connector port of the Lock Assembly and then secure
the excess cable on the bridge lance of the Security Door.

7360-K051 Security Door Electronic Combination Lock 13
c. Align the Spindle hole of the Lock Assembly to the protruding Spindle and then
secure the Lock Assembly on the door using three (3) bolts, as shown in the
image below.
To change the combination of the Electronic Combination Lock, refer to Changing
Number Combination of Electronic Lock on page25.

14 7360-K051 Security Door Electronic Combination Lock
Opening Electronic Lock
To open the Electronic Lock, follow these steps:
1. Access the Security Door by using a key to unlock and open the NCRFastLane
SelfServ™ Checkout (7360) Cosmetic Door.

7360-K051 Security Door Electronic Combination Lock 15
2. On the Security Door, enter a valid combination in the Combination Lock. The
Combination Lock LEDflashes two times and beeps two times.
Note: If the combination is invalid, the Combination Lock LEDflashes three times
and beeps three times. Entering four consecutive invalid combination starts a five-
minute delay period, during which the Lock LED flashes red at ten-second intervals.
The five-minute delay period restarts after two more consecutive invalid
combination entries.
3. Within four seconds, turn the Security Door Knob and Combination Lock to the
open position and then open the Security Door.

16 7360-K051 Security Door Electronic Combination Lock
Opening Keylock
To open the Keylock, follow these steps:
1. Access the Security Door by using a key to unlock and open the NCRFastLane
SelfServ™ Checkout (7360) Cosmetic Door.

7360-K051 Security Door Electronic Combination Lock 17
2. On the Security Door, insert the Setup Key or current Operating Key into the
keyhole.
Caution: Do not force the key into the lock to avoid causing permanent damage to
the Lock or the Key. Do not apply inward or outward axial force to the Key once it is
inserted to avoid causing the Lock from opening incorrectly.
3. Turn the Key to the Right until it stops and the bolt is retracted.
4. Turn the Security Door Knob and Keylock to the open position and then open the
Security Door.