NCTeco AL10 Series User manual
Installation Guide
Model: AL10/AL20 Series
Lock Body: American Standard Single Latch
Version: 1.0
Important Notes
Please read this Installation Guide carefully or contact the Customer Care for any
queries regarding installation.
Installation is recommended to be performed by a professional to avoid any
additional service charges that may cause due to improper product installation.
We constantly revise the contents of this Installation Guide and update our products
to improve the quality and performance without any prior notice.
Do not insert batteries before installing the lock.
1.
2.
3.
4.
Table of Contents
What's in the Box.............................................................................................................1
Installation Diagram.......................................................................................................2
Installation Procedure....................................................................................................2
1. Door Properties..........................................................................................................................................2
2. Drilling Holes on the Door......................................................................................................................4
3. Installing Latch...........................................................................................................................................4
4. Installing Outdoor Unit............................................................................................................................5
5. Installing Mounting Plate and Gasket.................................................................................................5
6. Installing Indoor Unit...............................................................................................................................6
7. Installing Battery and Cover...................................................................................................................6
8. Installing Strike Plate and Box...............................................................................................................7
9. Physical Testing..........................................................................................................................................7
What's in the Box
Outdoor Unit Indoor Unit Gasket Mounting Plate
Latch
Spindle
Strike Plate and Box Keys MF Cards Hex wrench
Screw A Screw B Screw C Screw D
Door Thickness
30 to 38 mm
39 to 46 mm
47 to 54 mm
Spindle
56 mm
64 mm
72 mm
Spindle B
20 mm
30 mm
35mm
Screw C
25 mm
35 mm
40mm
Note: Screws and Spindles for the doors of thickness from 30 to 54 mm are included in the
standard package. Please use the appropriate set of screws as per your door's thickness, to
assure the proper functioning of the lock.
1
Installation Diagram
2
Installation Procedure
1Door Properties
Check the door thickness
A.
After measuring the door’s thickness, select the proper Spindle and Screw length. For
details, please refer to the table contents of Page 1.
Check the door opening direction
B.
The handle of the door is determined by the swing (handing) direction of the door. Below
is the graphical representation of handing in reference to your location outside the room.
Indoor Unit Keys
Door Outdoor Unit
Gasket
Mounting
Plate
Gasket
Battery Cover
Strike Plate and Box
Latch
Screw D
Screw A
Screw B
Screw C
Spindle
Battery
(not included)
3
User Location
LatchStrikePlateLatch
LatchStrikePlateLatch StrikePlate
StrikePlate
Left Inward Right Inward
Left Outward Right Outward
Change the handle direction (if needed)
C.
Use the hex wrench to remove the screw of handle. Take the handle out from the lock.
Change the handle direction and replace. Secure it by using the screw.
1)
2)
4
2Drilling Holes on the Door
Place the Installation Template at the desired handle height.
Mark for the holes to be drilled and drill the marked places.
1)
2)
3Installing Latch
Adjust the backset of the lock. (if needed)
Secure the Latch with the Screw A. Make sure the latch angle faces the door jamb.
1)
2)
Desired handle height
30~54mm
2-3/4
2-3/4
2-3/8
70mm
60mm
70mm
2-3/4 2-3/8
60mm
Screws A
Backset
Center line of handle
Screws C
5
Attach the Gasket to the Outdoor Unit.
Insert Spindle into the clutch.
Attach the Outdoor unit to the door by inserting the cable through the drilled holes.
4Installing Outdoor Unit
1)
2)
3)
5Installing Mounting Plate and Gasket
Attach the Mounting Plate to the Gasket and route the cable through the hole.
Place the Gasket and Mounting Plate on to the door and use Screw C to secure them.
1)
2)
Clutch c orrect p osition:
T he triangle must be vertically centered.
Screws
BD
6
Connect the cable to the port on the Indoor Unit.
Place the Indoor Unit properly on the Mounting Plate. Then use Screw B & Screw D to
secure the Indoor Unit.
6Installing Indoor Unit
1)
2)
Insert four Alkaline AA batteries and cover them with a battery cover.
7Installing Battery and Cover
7
Make sure that the Strike Box is aligned with the latch bolt. Then, use the Installation
Template to drill holes.
Align the Strike Plate and Box with the drilled holes and secure them with Screw A.
8Installing Strike Plate and Box
1)
2)
9Physical Testing
Test the lock by rotating the
handle.
A.
Note: When the door is locked, the front
handle can be turned, but the door will
remain locked.
B. Test the lock by using the
mechanical key.
Insert the Key into key hole and rotate
90°, then rotate down the handle to
open the door.
Screws A
58(mm)
(2-36/127")
(215/254")
(1-48/127")
2(mm)
(10/127")
14(mm)
(70/127")
35(mm)
(1-18/127")
29(mm)
21.5(mm)
depth
depth
1
23
4
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
IMPORTANT! Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning:
FCC RF Radiation Exposure Statement:
This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment complies with RF radiation exposure limits set forth for an
uncontrolled environment.
Copyright©2020 NGTECO E-COMMERCE CO., LIMITED. All rights reserved.
1600 Union Hill Road Alpharetta, GA 30005
Tel: 770-800-2321(US)
www.ngteco.com
This manual suits for next models
1
Table of contents
