Neilsen CT0310 User manual

CONCRETE MIXER CT0310 & CT0313
ELECTRIC MOTOR
INSTRUCTION MANUAL
Please keep this instruction manual for future reference

EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety and
health requirements of the EC Directive based on its design and type, as brought
into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: CONCRETE MIXER
Model: CT0310 CT0313
Applicable EC Directives:
EC-Machinery Directive 2006/42/EC
EC- Directive of Electromagnetic Compatibility：2014/30/EU
Applicable Harmonized Standards:
EN 61000-6-4, EN 61000-6-2
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2017-08-31

NAME OF MAIN PARTS
1. MIXING DRUM 6. 400mm H/DUTY WHEELS
2. ON/OFF SWITCH 7. MIXER BASE FRAME
3. HANDLE GRIPS 8. DRAW BAR FRAME
4. MOTOR AND GEAR BOX DRIVE 9. GEAR BOX MOUNTING FRAME
5. MOTOR COVER SHIELD 10. SAFETY CUT OUT SWITCH
DATA OF PRODUCT
capacity
140L
Frequency
50/60 Hz
Voltage
230/110V
Power
375W
Motor speed
1380rpm
Capacities based on usable volume. Product development and improvement is an ongoing
process, therefore specifications may change without notice.

SAFETY
IMPORTANT!
PLEASE READ THIS SECTION CAREFULLY ！
Your Mixer has been designed with safety in mind. However as with any type of machinery
some basic rules apply:
DO NOT Place your hand or hands in or around any part of the
drum while it is operating!
DO NOT Place any tools or instruments in or around the drum
while it is operating!
DO NOT Operate the mixer on a surface that is not flat or is
uneven! Always operate the mixer on a level surface, if placed
on an incline the machine will fall over.
DO NOT Clean, assemble or work on the unit while it is
plugged in!
DO NOT Allow water to contact the motor or electrical
connections at any time!
DO NOT Ignore the safety cut out switch. If your mixer
should stop during use it normally indicates a break in power supply, check and rectifies any
problem in power supply.
DO NOT Set up or operate the Mixer in or around water puddles.
DO NOT Leave Mixer unattended, whilst in operation!
DO NOT Operate Mixer while under the influence of alcohol or drugs!
DO NOT Start or stop the Mixer when there is material in the Mixer Drum. This will damage the
motor. Always make sure the Mixer Drum is Rotating when filling or discharging material.
DO NOT Attempt to move Mixer when there is material in the Mixer Drum.
DO Read all instructions before operating the Mixer.
DO Keep Mixer clean. Wash down immediately after use. Any build up of cement and concrete
on your Mixer, will seriously affect the performance and reduce the life of the Mixer.
DO Disconnect the Power supply before moving the Mixer.
DO Keep all moving parts, lightly greased. (Wheels, Axles, Swivel Brackets, etc)
DO Periodically check the Mixer for wear or damage.
DO Wear protective safety wear. It is advised not to wear loose clothing when using Mixer.

DRESS PROPERLY
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wrist watches).
They can be caught in moving parts. Protective electrically
on-conductive gloves and non-skid footwear are recommended
when working.
Wear protective hair covering to contain long hair, preventing it
from getting caught in Machinery.
Wear a face or dust mask if the operation is dusty.
Always wear safety goggles and/or face shields. Everyday
eyeglasses have only impactresistant lenses, they are not
safety glasses.

ASSEMBLY OF CEMENT MIXER
STEP1. Place the Mixer Base Frame (Ref 7) onto a Level Surface. Then fix the Base Frame to
the Gear Box Mounting Frame (Ref 9) using the 4x3” (75mm) Bolts with 1xWashers and Nuts
provided. The washers are shaped to fit around the contour of the Mixer Frame. Make sure all 4
Bolts are tight and secure before proceeding.
STEP2. The fix the Draw Bar Frame (Ref 8) to the Gear Box Mounting Frame (Ref 9) using the
4X3” (75mm) Bolts with 2 x Washers and Nuts provided. You will note there are 2 Washers
supplied with each Bolt. These should be positioned either side of the Frame. Again these
Washers are shaped to fit around the contour of the Frame. Tighten and secure all 4 Bolts
before proceeding.
STEP3. Fit the 2 Rubber Wheels (Ref 6) to the Gear Box Mounting Frame (Ref9) by sliding the
Wheels onto the Axil. Once in place. Secure with the 2 Bolts / Washer Set (Ref 11). Tighten
Bolts securely, before proceeding.

STEP4. Turn the assembled Frame of the Mixer on its side. Refer to diagram below. Take the
Motor and Gear Box Drive unit. Lining up the 5 exposed Bolts with the 5 Holes, predrilled in the
Back plate on the Gear Box Mounting Frame. Secure the Motor Gear Box, using the 5 Locking
Nuts provided once secure, turn the Frame onto its upward position.
STEP5. Fit the Motor Gear Box Cover shield (Ref 5) to the Gear Box Mounting Frame (Ref 9)
using the 2 small Nuts and Bolts provided.
STEP6. Mount the Cement Mixer Drum (Ref 1) onto Assembled Frame by locating the Gear
Box Shaft, through the Centre Hole in the Mixer Drum.
Use locating Point on the Gear Box Shaft to position correctly. Then take the large washer
(Ref12) and black spring washer (Ref 13) and place on the "T" Handle (Ref 14). Screw the "T"
Handle into the Gear Box Shaft. Secure tightly before proceeding.
Note: Mixing Blades Preassembled in Mixer Drum.

STEP7. Fix Tilting Handle (Ref 17) by locating
the holes in the Tilting Handle Base Plate with
the three Brackets on the under side of the
Gear Box Mounting Frame (Refer to Diagram
below). Once Holes are alined secure by using
Metal Bolt (Ref 15) lock with Cottar Pin (Ref 16).
STEP8. Please note the 4 legs are marked either "A" or "B". Take legs marked "A" and Central
Pole (Ref 18). Using the two 4 5/8" Bolts with two Washers, Join the two Legs and Central Pole
(Refer to Diagram below). Then take the Legs marked "B" and join to Central Pole. The
washers are shaped to fit round the contour of the Frame. Secure before proceeding.

STEP9. Now both Cement Mixer and Cement Mixer Stand are fully assembled. You can now fit
the Mixer to the stand. This is simply done by:
* Laying Mixer on its Back (Ref to Fig.1)
* Connect Central Pole (Ref 18) on the stand into the Tilting Handle Base Plate (Ref 17) on the
underside of the cement mixer.
* Once this is done. Simply lift the Mixer into its upright position (Fig. 3)

NOISE EMISSION LEVEL
The Mixer has a noise emission level of 69 decibels.
WIRING DIAGRAM
S1 SWITCH
F1 THERMAL PROBE
C1 CONDENSER
X1 MOTOR CONNECTOR
PE EARTH TERMINAL
N NEUTRAL TERMINAL
L 1 LIVE TERMINAL
AM MOTOR RUNNING WINDING
K1 RELAY
WARNING
Any type of electrical repair or trouble-shooting should only be performed by an appointed
dealer or a properly qualified electrical repair shop.