nekos PIK User manual

INSTRUCTION MANUAL
30 CHANNEL REMOTE CONTROL
433,92MHz
NEKOS S.r.l. -
Via Capitoni, 7/5
[phone]
EN
4420066 – Rev. 2003
PIK
INSTRUCTION MANUAL
30 CHANNEL REMOTE CONTROL
Via Capitoni, 7/5
- 36064 Colceresa (VI)
–
[phone]
–  [phone] - www.nekos.it -
[e-mail]
–
ITALY
[email protected]
2
USER INSTRUCTIONS
CAUTION. Carefully observe all the following installation
instructions to ensure personal safety.
The device is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lacking
experience and knowledge. Do not allow children to play with the
fixed controls and keep any remote-control units out of their reach.
Have installation checks performed periodically by qualified
personnel from a service centre authorised by the manufacturer. Do
not use if repair or adjustment is required.
CAUTION: if the power cable is damaged, it must be replaced by
qualified personnel from a service centre authorised by the
manufacturer.
CAUTION. Disconnect the power supply during cleaning or
maintenance operations. Do not use solvents or jets of water to
wash the appliance; the appliance should not be submerged in
water.
In the event of fault or malfunction, switch off the device at the main
switch. All repairs and adjustments (e.g. setting the stroke) must
only be performed by qualified personnel from a service centre
authorised by the manufacturer.
Always request exclusive use of original spare parts. Failure to
respect this condition could compromise safety and invalidate the
benefits contained in the warranty for the appliance. In the event of
any problems or queries, consult your agent or contact the
manufacturer directly.
The A-weighted sound pressure level is less than 70dB(A).
Carefully preserve these instructions after installation.

INSTALLER INSTRUC
nekos
products have been manufactured in accordance with safety standards and
conforms to the stipulations of current standards in force.
When correctly assembled, installed and used according to the present instructions, they
will not generate any danger for persons, animals or items.
Symbols used in the manual
DANGER
Contents
1. Safety indications
................................
 General notes
................................

Notes for functioning
2. Technical data
................................
3. Technical
and constructional information
4.
ID plate and marking data
5. Instructions for start-up
................................
 Standby state
................................
 Wait state
................................

Selection of the channel

Storage of the M1 and M2 memory groups

Control of a stored sequence

F1 and F2 Function buttons
6.
Battery status indication
7.
Environmental protection
8.
Recall to main principles of warranty c
9. Declaration
of conformity
3
INSTALLER INSTRUC
TIONS
products have been manufactured in accordance with safety standards and
conforms to the stipulations of current standards in force.
When correctly assembled, installed and used according to the present instructions, they
will not generate any danger for persons, animals or items.
Symbols used in the manual
This indication draw the attention about potential dangers
for
safety and health of peoples and animals.
................................
................................
................................
................................
................................
................................
Notes for functioning
and use ................................
................................
................................
................................
................................
and constructional information
................................
................................
ID plate and marking data
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
Selection of the channel
................................
................................
Storage of the M1 and M2 memory groups
................................
Control of a stored sequence
- M1 and M2 Memories
................................
F1 and F2 Function buttons
................................
................................
Battery status indication
................................
................................
Environmental protection
................................
................................
Recall to main principles of warranty c
ertificate
................................
of conformity
................................
................................
TIONS
products have been manufactured in accordance with safety standards and
When correctly assembled, installed and used according to the present instructions, they
This indication draw the attention about potential dangers
safety and health of peoples and animals.
................................
..... 4
................................
.... 4
................................
............ 4
................................
......... 5
................................
6
................................
....................... 6
................................
............................ 6
................................
..... 6
................................
........... 7
................................
.................... 7
................................
....................... 7
................................
...... 8
................................
............... 8
................................
.......................... 8
................................
......................... 9
................................
...................... 9
................................
....................... 10
1. Safety indications
General notes
ATTENTION
:
Before installing this appliance, ensure all safety
indications have been read carefully and understood in order to prevent
contact with electricity, injury or any other incident.
be conserved for further consultation at a later date
WARNING
D
ANGER OF EXPLOSION I
DIFFERENT TYPE OF BA
WITH CURRENT REGULAT
The manufacturer accepts no responsibility for damage to
animals or things
incurred by improper use.
Use for any applications other than those indicated must be authorised
by the manufacturer after technical review of the assembly.
Plastic bags, polystyrene, small metal parts such as nails, staples etc should
be placed out of the reach of children as they constitute a potential source of
risk.
The appliance is not intended for use by people (including children) whose
physical, sen
sory and mental abilities are reduced, or in case of lack of
experience or knowledge; such persons must be supervised to ensure that
they do not play with the appliance.
Do not use solvents or jets of water to wash the appliance. The appliance
should not
be submerged in water.
Before using the remote control, check that installed batteries have the
same nature, quality and tension as those indicated on the technical data
label on the appliance.
Run-
down batteries do not belong in normal household waste.
disposed of properly.
The batteries must always be replaced with suitable models corresponding
to the specifications provided on the label attached inside the battery
compartment door. Failure to observe this rule may compromise safety and
void the warranty.
Note
s for functioning and use
PIK is a radio transmitter
provided of a receiver
with the same code protocol or the same transmission
philosophy.
For further details see chapter “

This product is designed to be used with the manufacturer's original products.
Use with any other products may result in damage or malfunctions.
 The initial start-
up of the radio remote control should be carried out by a skilled
and qualified perso
n following the manufacturer's instructions.

After removing packaging, check for any damage on the appliance
4
Before installing this appliance, ensure all safety
indications have been read carefully and understood in order to prevent
contact with electricity, injury or any other incident.
be conserved for further consultation at a later date
ANGER OF EXPLOSION I
F THE BATTERIES ARE
DIFFERENT TYPE OF BA
TTERY
. D
ISPOSE OF THE USED B
ATTERIES IN COMPLIAN
WITH CURRENT REGULAT
IONS
The manufacturer accepts no responsibility for damage to
incurred by improper use.
Use for any applications other than those indicated must be authorised
by the manufacturer after technical review of the assembly.
Plastic bags, polystyrene, small metal parts such as nails, staples etc should
be placed out of the reach of children as they constitute a potential source of
The appliance is not intended for use by people (including children) whose
sory and mental abilities are reduced, or in case of lack of
experience or knowledge; such persons must be supervised to ensure that
they do not play with the appliance.
Do not use solvents or jets of water to wash the appliance. The appliance
be submerged in water.
Before using the remote control, check that installed batteries have the
same nature, quality and tension as those indicated on the technical data
label on the appliance.
down batteries do not belong in normal household waste.
disposed of properly.
The batteries must always be replaced with suitable models corresponding
to the specifications provided on the label attached inside the battery
compartment door. Failure to observe this rule may compromise safety and
s for functioning and use
– or simpler a remote control
–
with the same code protocol or the same transmission
For further details see chapter “
Technical data”.
This product is designed to be used with the manufacturer's original products.
Use with any other products may result in damage or malfunctions.
up of the radio remote control should be carried out by a skilled
n following the manufacturer's instructions.
After removing packaging, check for any damage on the appliance
Before installing this appliance, ensure all safety
indications have been read carefully and understood in order to prevent
contact with electricity, injury or any other incident.
The manual should
be conserved for further consultation at a later date
.
F THE BATTERIES ARE
REPLACED WITH A
ATTERIES IN COMPLIAN
CE
The manufacturer accepts no responsibility for damage to
people,
Use for any applications other than those indicated must be authorised
by the manufacturer after technical review of the assembly.
Plastic bags, polystyrene, small metal parts such as nails, staples etc should
be placed out of the reach of children as they constitute a potential source of
The appliance is not intended for use by people (including children) whose
sory and mental abilities are reduced, or in case of lack of
experience or knowledge; such persons must be supervised to ensure that
Do not use solvents or jets of water to wash the appliance. The appliance
Before using the remote control, check that installed batteries have the
same nature, quality and tension as those indicated on the technical data
down batteries do not belong in normal household waste.
They must be
The batteries must always be replaced with suitable models corresponding
to the specifications provided on the label attached inside the battery
compartment door. Failure to observe this rule may compromise safety and
–
to command devices
with the same code protocol or the same transmission
This product is designed to be used with the manufacturer's original products.
Use with any other products may result in damage or malfunctions.
up of the radio remote control should be carried out by a skilled
n following the manufacturer's instructions.
After removing packaging, check for any damage on the appliance
.


This machine is destined exclusively for the use for which it has been designed and
the manufacturer accepts no responsibility for damage incurred

Repairs should only be performed by qualified personnel at assistance centres
authorised by the manufacturer.

The product must be disposed of in compliance with local environmental
regulations and not as household waste.
 For any doubts, c
ontact your local waste collection company.
2. Technical data
Type
Number of transmission
channels
Carrier frequency
Modulation
Class
Maximum transmitter output
power
Band width
Duty cycle
Power supply voltage
Operating voltage
Estimated lifetime of the
batteries
Display
Visualization
Display dimensions
Encoding
Independent codes
Absorption in standby
Absorption in transmission
Keypad
Transmission distance
Dimensions
Weight
Any information reported in this table is not binding and may be susceptible to variations without notice.
5
This machine is destined exclusively for the use for which it has been designed and
the manufacturer accepts no responsibility for damage incurred
Repairs should only be performed by qualified personnel at assistance centres
authorised by the manufacturer.
The product must be disposed of in compliance with local environmental
regulations and not as household waste.
ontact your local waste collection company.
Multi-
channel radio remote control with
microprocessor
30
433.92 MHz
OOK (On-Off Kejing)
1
< 1mW
433,05-434,79 MHz
< 1%
2 1.5V batteries - type AAA
alkaline
1.8V - 3.3V
> 2 years
(assuming an average
day)
LCD (liquid crystal display)

2 digits (selected channel)
;

Battery charge status indicator;

Transmission status;

Specific function letters
18.5x13.5 mm
HCS301
>18 x 10^18 “rolling code” combinations
< 1 µA
< 20 mA

Operational control (
UP
ARROW
STOP
);

2 Function buttons (F1, F2
);

1 Memory button (M);

1 Channel button (CH);
50 m –
(with charged batteries)
145x38.5x22.5
76 g
Any information reported in this table is not binding and may be susceptible to variations without notice.
This machine is destined exclusively for the use for which it has been designed and
the manufacturer accepts no responsibility for damage incurred
by improper use.
Repairs should only be performed by qualified personnel at assistance centres
The product must be disposed of in compliance with local environmental
ontact your local waste collection company.
channel radio remote control with
alkaline
(assuming an average
use of 1 minute per
;
Battery charge status indicator;
>18 x 10^18 “rolling code” combinations
ARROW
,
DOWN ARROW
,
);
(with charged batteries)
Any information reported in this table is not binding and may be susceptible to variations without notice.
6
3. Technical and constructional information
 The PIK radio remote control transmits radio waves at the frequency of 433.92
MHz. It has a protocol that changes its code at each transmission (rolling code)
according to a predetermined algorithm with a total of over 18 x 10^18 possible
combinations.
 30 Direct transmission channels (from 01 to 30). With the F1 and F2 functions
implemented, there can be as many as 90 control outputs for specific
transmission processes.
 The command issued can be received by an electrical appliance equipped with a
receiver of the same nature which has already been set up for reception.
 The casing is constructed in recyclable thermoplastic material (PC-ABS -
(Polycarbonate-Acrylonitrile Butadiene Styrene)) which is particularly shock
resistant.
 The batteries are enclosed by a snap door.
 Powered by 2 AAA alkaline 1.5V batteries. (The radio remote control works
with voltages from 1.8V to 3.3V ).
 Provided with a liquid crystal display and silicone control keypad.
 The “free-field” transmission distance covers a sphere with a radius of 50 m.
4. ID plate and marking data
PIK remote controls have CE marking and comply with the Standards listed in the
Declaration of Conformity.
The plate data is displayed on an adhesive label placed on the outside of the casing,
which must remain intact and visible.
The main information it displays includes: manufacturer's address, product name -
model number, technical characteristics, production date and serial number.
In the event of a complaint, please indicate the serial number (SN) displayed on the
label.
An explanation of the symbols used on the label to abbreviate the technical
characteristics is given in the table in the chapter on “TECHNICAL DATA”.
5. Instructions for start-up
THESE INSTRUCTIONS ARE INTENDED FOR TECHNICAL AND SPECIALIZED PERSONNEL.
THUS BASIC SAFETY AND WORKING TECHNIQUES ARE NOT DISCUSSED.
Standby state
When the batteries are inserted, the radio remote control goes into a standby
state; the display is off and the microprocessor is in the power down state, so the
entire device is in a state of very low consumption.
The radio remote control returns to this state whenever 30 seconds have passed
since the last button was pressed.

7
Wait state
If any of the 7 buttons is pressed when the radio remote control is in standby, it
awakens and enters the wait state. The display shows the channel (one of the 30)
selected before the radio remote control went into standby state.
Selection of the channel
To select a (new) channel, press the CH button; the displayed channel starts
flashing. Use the ▲(UP) arrow or ▼(DOWN) arrow buttons to select the desired
channel, which flashes. By pressing the CH button again, the channel display
becomes steady-on.
If the newly selected channel is not activated by pressing the CH button, after a
standby or the next time the radio remote control passes to the wait state, the last
channel that was previously activated will appear on the display.
Storage of the M1 and M2 memory groups
The “sequence storage” state (M button) provides the possibility to assign two
distinct “memory groups”, i.e., two memories. The storage is carried out as
follows.
Memory M1
 Press the M button for 5 seconds to store the memory 1; the icon M1
appears flashing on the display.
 Scroll through the channels using the ▲▼ arrows, and the various
channels will flash. To enter the channel in the memory, press the STOP
button, the channel stops flashing and becomes steady-on; carry out this
operation for all the channels you would like to store, up to a maximum of
10 channels.
 To exit the channel storing mode, press the M button again for at least 1
second.
 To erase the memory, go to the channel 00 and press the STOP button. After
the memory has been erased, all the channels start flashing. To exit, press
the M button again for 1 second.
Memory M2
 Press the M button for 5 seconds, and the flashing icon M1 appears. Now
press the CH button and the icon M2 will appear flashing on the display.
 Scroll through the channels using the ▲▼ arrows, and the various
channels will flash. To enter the channel in the memory, press the STOP
button, the channel stops flashing and becomes steady-on; carry out this
operation for all the channels you would like to store, up to a maximum of
10 channels.
 To exit the channel storing mode, press the M button again for at least 1
second.
8
 To erase the memory, go to the channel 00 and press the STOP button.
After the memory has been erased, all the channels start flashing. To exit,
press the M button again for 1 second.
Checking the composition of a memory sequence
 From the wait state, press the M button; the M1 icon will be activated.
 The stored sequence of channels appears on the display (e.g.: 1-2-3-4-
pause, 1-2-3-4-pause, etc.).
Control of a stored sequence - M1 and M2 Memories.
Starting from the wait state, press the M button and the steady-on M1 icon will
appear on the display; using the ▲▼ buttons activates the function, transmitting
the command to the channels of the M1 sequence. The stored channels scroll
cyclically and continuously on the display.
Starting from the wait state, press the M+CH button and the steady-on M2 icon
will appear on the display; using the ▲▼ buttons activates the function,
transmitting the command to the channels of the M2 sequence. The stored
channels scroll cyclically and continuously on the display.
The STOP button stops the command.
Press the M button once to exit from the memory sequence control state, and the
M1 or M2 icon disappears; now it is possible to activate the commands of all the
individual channels.
F1 and F2 Function buttons
The F1 and F2 function buttons are dedicated to manage special functions if
foreseen in the dedicated motor; they are described inside its own manual.
WARNING:
For all the other “normal” applications – i.e., those not supported by the devices
described above - where the radio remote control is used, regardless of the
channel number on which it is set, if the steady-on F1 or F2 icon appears on the
display, NOTHING MOVES when the ▲▼ buttons are pressed because these
functions are not associated with any type of command.
IN THIS CASE, THE F1 AND F2 ICONS SHOULD NEVER APPEAR ON THE DISPLAY DURING
USE.
6. Battery status indication
The level of the battery charge is measured at each passage from the standby state
to the wait state. The level is shown on the display using the battery indicator:
Level above 2,6V : 3 bars lit
Level between 2,4V
and 2,6V
2 bars lit
Level between 2,2V and 2,4V 1 bar lit
Level below 2,2V : 0 bars lit – all off

9
7. Environmental protection
All materials used in the manufacture of this appliance are recyclable. We
recommend that the device itself, and any accessories, packaging, etc. be sent to a
centre for ecological recycling as established from laws in force on recycling. The
device is mainly made from the following materials: aluminium, zinc, iron, plastic of
various type, cuprum. Dispose materials in conformity with local regulations about
removal.
8. Certificate of guarantee
The manufacturer will guarantee good function of the appliance. The manufacturer
shall undertake to replace defective parts due to poor quality materials or
manufacturing defects in accordance with article 1490 of the Civil Code. The
guarantee covers products and individual parts for 2 years from the date of
purchase. The latter is valid as long as the purchaser possesses proof of purchase
and completion of all agreed conditions of payment.
Guarantee of good function of appliances agreed by the manufacturer implies that
the latter undertakes to repair or replace free of charge and in the shortest period
possible any parts that break while under warranty. The purchaser is not entitled to
any reimbursement for eventual direct or indirect damage or other expenses
incurred.
Attempt to repair by personnel unauthorised by the manufacture shall render the
warranty null and invalid. The warranty does not cover fragile parts or parts subject
to natural wear and tear or corrosion, overload, however temporary etc.
The manufacturer will accept no responsibility for eventual damage incurred by
erroneous assembly, manoeuvre or insertion, excessive stress or inexpert use.
Repairs performed under guarantee are always "ex factory of the manufacturer".
Respective transport expenses (out/back) are the responsibility of the purchaser.
10
9. Declaration of conformity
The undersigned,
Company name: NEKOS S.r.l
Postal address: Via Capitoni, 7/5
Postcode and city: 36064 Colceresa VI
Telephone number: [phone]
E-mail address: [email protected]
declare that the document is issued under our sole responsibility and belongs to the following product:
Apparatus model / Product: 30 channel remote control PIK
Trademark: NEKOS
Model/Type: PIK
Batch: see data label
Serial number: see data label
The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:
 2014/53/EU Radio Equipment (RED)
 2011/65/EU Restriction of the use of certain hazardous substances Directive (RoHS Directive)
 2015/863/EU Delegated Directive amending Annex II of Directive 2011/65/EU of the European Parliament
and of the Council regarding the list of substances with usage restrictions
The following harmonised standards and/or technical specifications have been applied:
RED
ETSI EN 300 220-1 V3.1.1 – ETSI EN 300 220-2 V3.2.1
ETSI EN 301 489-1 V2.2.3 – ETSI EN 301 489-3 V2.1.1
LVD
EN 62368-1:2014 + A11:2017 + AC:2017
EN 62479:2010
RoHS
EN 50581:2012
Place: Colceresa
Date: 04/03/2020
Signature: Giuliano Galliazzo (A.D. – President)

11
Notes
12
NEKOS S.r.l. - Via Capitoni, 7/5
36064 Colceresa (VI) – ITALY
[phone] –  [phone]
www.nekos.it [email protected]