NETGEAR ProSafe FR114P User manual

Installation Guide
Cable/DSL ProSafe Firewall
MODEL FR114P
with Print Server

Introduction
Thank you for purchasing a NETGEAR FR114P Cable/DSL ProSafe Firewall with Print Server.
A firewall is a special type of router that incorporates features for network security. With this
firewall you can have secure Internet access through a high-speed DSL or cable modem and share
the single modem with several computers. The FR114P also incorporates a built-in print server.
This installation guide shows you how to connect the firewall and configure it and your
computers for secure Internet access. Setup is easy—follow the instructions in this guide and
your system will be up and running quickly.
If you have problems, there is a troubleshooting section on page 13 to help you—or you can
get more detailed troubleshooting information from the Reference Manual on the CD, online
from www.NETGEAR.com or by phone.
Installation Overview
Estimated time: 15 to 30 minutes
1. Gather the configuration information you have for your working DSL or cable modem
connection to the Internet.
2. Install the firewall between the DSL or cable modem and one computer.
3. Configure that computer to work with the firewall and restart the computer and modem.
4. Configure the firewall and go online to test the connection.
5. Connect other computers, configure them and restart each. (optional)
6. Configure for using the print server. (optional)
On the FR114P Resource CD, you’ll find the FR114P Installation Assistant, which supplements
the instructions in this installation guide by animating the step-by-step procedures given here.
For more detailed information about installation, troubleshooting and configuration
procedures, see the Reference Manual on the CD.
Model FR114P ProSafe Firewall with Print Server
1

What’s in the Box
When you open the box, verify that you received everything.
The package includes:
• FR114P Cable/DSL ProSafe Firewall with Print Server
• AC power adapter
• Ethernet patch cable
• FR114P Resource CD, including a full Reference Manual and Installation Assistant.
• FR114P Installation Guide (this document)
• Warranty and registration card
• Support information card
If you don’t have everything listed above, see the support information card for contact informa-
tion. If the support information card is missing, you can get contact information at www.NET-
GEAR.com in the Customer Service area.
2
FR114P Resource CD,
installation guide,support
information card &
warranty/registration card
Power adapter
Category 5
100 Mbps
Ethernet cable
Model FR114P ProSafe Firewall with Print Server

Gather Configuration Information for
Your Working Connection to the Internet
Before installing the FR114P firewall, you
should have an external DSL or cable
modem with an Ethernet port set up and
working with one computer. You’ll be
installing the firewall between the modem
and the computer.
For each computer that you want to con-
nect to the firewall, you must have
• An available RJ-45 Ethernet port (or
adapter) — either built-in or from a
network interface card (NIC) installed
in the computer.
Note: If you have a built-in modem
or a modem card, the telephone jack
for the modem looks very similar to
an RJ-45 Ethernet port, but the RJ-
45 port is larger.
• TCP/IP installed.
• If your computer is a Windows®computer, it must have the Client for Microsoft®
Networks software installed.
Note: Please see the Reference Manual on the CD if you need help installing
TCP/IP software or the Client for Microsoft Networks software on any Windows
computer that hasn’t been networked previously.
• A Category 5 (Cat 5) Ethernet patch cable
Note: There is one cable in the box with the firewall.
3
DSL modem
1
1
Note: If you have a cable
modem, you will have a cable
connection between the
modem and your cable outlet.

Connection information
Later in the setup process you’ll need to configure the firewall to work with your network. A
Setup Wizard is available to help you through this procedure. You can configure the firewall
yourself using information that you can get from your computer or your ISP about your
current Internet connection.
The next page includes blanks for you to fill in and refer to later. To get the needed
information from your computer:
• Open the Network control panel, select the TCP/IP entry, and click Properties.
(Windows 98/Me)
• Open Local Area Network Connection and click Properties. (Windows 2000/XP)
• Open the TCP/IP (or Network) control panel. (Macintosh®)
Your ISP should have provided you with a summary sheet of all the information needed to connect
your computer to the Internet. If you cannot locate the information, you’ll have to contact your ISP.
An ISP Guide is included with your firewall’s documentation, either as a printed card or on the
Resource CD. The ISP Guide contains specific configuration guidelines for connecting to
many popular ISPs.
4

Host and Domain Names
Some ISPs use a specific host or domain name—like jsmith or earthlink.net. If you haven’t
been given specific information about host or domain names then use the following examples
as a guide:
• If your main e-mail account with your ISP is [e-mail], then use aaa as your host
name. (Your ISP might call this your account name, user name, or system name.)
• If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.
Host name:_____________________________________
Domain name: __________________________________
Login Name
If your ISP requires a login name and password (possibly because you have a PPPoE account),
fill in the following:
Login name:____________________________________
(may be your full e-mail address)
Password:______________________________________
Note: The login name could be called a user name or account name by your ISP.
The login name is case sensitive. You must type it exactly as given by your ISP. For
example, c_jones is a different login name than C_Jones or cjones.
Fixed (or static) IP address
If you have a static IP address through your ISP, fill in the following information:
IP address: _____._____._____._____
Subnet mask: _____._____._____._____
Gateway IP address:_____._____._____._____
DNS server address information
If you were given specific Domain Name System (DNS) server addresses, fill in the following:
DNS Server IP address(es): _____._____._____._____
_____._____._____._____
5

Install the Firewall
After unpacking the box and locating the
configuration information, you’re ready to install
the firewall.
Note: You do not have to power down any
equipment to do this, but if you need to move
your computers (perhaps to get to ports in
the back), you may want to shut down the
computers before moving them around.
1. Locate the Ethernet cable currently going
from the DSL or cable modem to the com-
puter that you use to access the Internet.
Note: You must use this cable to connect the
DSL or cable modem to your firewall since
this may be a special cable even though it
looks like other LAN cables.
2. Remove this cable from the computer and insert that end into the Internet port on the
rear panel of the firewall.
3. Use the Ethernet patch cable that came with the firewall to connect the computer to one
of the four numbered local Ethernet ports on the rear panel of the firewall.
4. Connect the power adapter’s cord into the back of the firewall and then plug the adapter
into a power source (such as a wall socket or power strip).
Note: If you want to connect other computers to the firewall, don’t connect them
now. Do that after you know that the modem/firewall setup works with one
computer.
6
PRINTER Normal
UpLink 12VDC0.8A
4321
LOCAL
10/100M
INTERNET
DSL
modem
Model FR114P ProSafe Firewall with Print Server

Check the setup
• The Test light turns on for a few seconds and then goes off.
Note: If the Test light remains on for more than one minute, go to Troubleshooting
on page 13.
• The Power and Internet Link lights should be lit.
• If your computer is on, the Local Link light should be on for the port number that your
computer is connected to.
Note: If the port connection is a 100 Mbps connection, the 100 light should be on.
If either the Power, Internet Link, or Local port Link light isn’t lit, go to Troubleshooting on
page 13.
7

Configure the Computer to Work with the
Firewall and Restart the Network
Next, make sure that the computer can interact with the firewall. To do this, configure the
TCP/IP settings on the computer and then restart the network. How you do this depends on
your computer.
Windows Operating System
Normally, you can leave the TCP/IP setup parameters at their factory default settings unless
you have a specific reason to change them. You should verify that the computer is set to ‘obtain
an IP address automatically’ in the Network control panel.
Windows 98 or Me
1. Choose Settings>Control Panel from the Start menu.
2. Double-click the Network icon.
3. Click the Configuration tab.
4. In the list of installed network components, select the TCP/IP entry for the computer’s
Ethernet adapter or NIC.
5. Click Properties.
6. Click the IP Address tab.
7. Check that Obtain an IP Address Automatically ia selected, select if not.
8. Click the Gateway tab.
9. Select and remove any IP Gateway addresses that are listed.
10. Click OK and click OK again to close the Network control panel.
11. Go to Restarting the Network on the next page.
Windows 2000 or XP
1. Right-click My Network Place and choose Properties.
2. Double-click Local Area Network Connection and
click Properties.
3. Select Internet Protocol (TCP/IP) and click Properties.
4. Select Obtain IP address automatically.
5. Click OK twice and click Close.
6. Go to Restarting the Network.
8
3
3
Windows 98/Me

Macintosh Operating System
Mac OS®8.6 or 9.x
1. Choose Control Panels >TCP/IP from the Apple
menu.
2. If not already selected, select Ethernet in the
Connect via list.
3. Select Using DHCP Server in the Configure list.
4. Click the close box.
5. If asked if you want to save this configuration,
click Save.
6. Go to Restarting the Network.
Mac OS X
1. Choose System Preferences from the Apple menu.
2. Double-click Network.
3. If not already selected, select Built-in Ethernet in the Configure list.
4. If not already selected, select Using DHCP in the TCP/IP tab.
5. Click Save.
6. Go to Restarting the Network.
Linux®or UNIX®Operating System
If you’re installing the firewall with a Linux-based or UNIX-based computer see your system
documentation for TCP/IP and networking setup information.
Restarting the Network
Once you’ve set up your computer to work with the firewall, you must reset the network for
the devices to be able to communicate correctly.
1. Turn off the DSL or cable modem, wait 15 seconds, and then turn it on again.
Note: If the modem doesn’t have an on/off switch, either pull the modem’s power
adapter out of the wall socket or power down the power strip.
2. If the firewall was powered down, power it up again and wait until the Test light turns off.
3. Restart the computer that is connected to the firewall.
9