NETGEAR ProSafe FVS318N User manual

1
Basic Wireless Configuration and
Security
This quick start guide provides basic wireless configuration information for the ProSafe
Wireless-N 8-Port Gigabit VPN Firewall FVS318N. For information about more complicated
wireless features, and for complete configuration steps, see the Reference Manual. This quick
start guide contains the following sections:
•Default Wireless Settings
•Wireless Equipment Placement and Range Guidelines
•Configure the Country of Operation
•Configure WPA+WPA2 with PSK Security
•Configure Wi-Fi Protected Setup for Easy Configuration of Wireless Clients
•Test Wireless Connectivity
•For More Information
Note: For more information about the topics covered in this guide, visit the
FVS318N support website at http://support.netgear.com. You will
also find the Reference Manual at the support website.
Default Wireless Settings
The default wireless settings should work well for most wireless networks, but you do need to
configure the country of operation and wireless security. These are the default settings:
Table 1. Default wireless settings
Item Description
Wireless radio Enabled
Region Nonconfigurable; set for the region in which you purchased the wireless
VPN firewall.

Basic Wireless Configuration and Security
2
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Country The selection is limited to the countries in the region in which you
purchased the wireless VPN firewall. The default settings are:
• Africa. Algeria
• Asia. Azerbaijan
• Europe. Albania
• Middle East. Bahrain
• North America, Latin America, and The Caribbean. United States
• Oceania. Australia
Operating frequency Nonconfigurable: Set at 2.4 GHz
Default security profile default1
Default network name (SSID) FVS318N_1
Broadcast SSID Enabled
Security Open
Encryption None
Authentication None
Transmission rate Best1
Default transmit power Full
802.11 wireless mode 802.11ng (this is the default for most countries)
802.11b/g/n radio frequency channel Auto
802.11n channel spacing 20 MHz
Beacon interval 100 ms
DTIM interval 2
RTS threshold 2346 bytes
Fragmentation threshold 2346 bytes
Preamble mode Long
Protection mode None
Power save Disabled
1. The maximum wireless signal rate derived from IEEE Standard 802.11 specifications. The actual throughput varies. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data
throughput rate.
Table 1. Default wireless settings (continued)
Item Description

Basic Wireless Configuration and Security
3
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Wireless Equipment Placement and Range Guidelines
The range of your wireless connection can vary significantly based on the location of the
wireless VPN firewall. The latency, data throughput performance, and notebook power
consumption of wireless adapters also vary depending on your configuration choices.
Note: Failure to follow these guidelines can result in significant performance
degradation or inability to wirelessly connect to the wireless VPN firewall.
For complete performance specifications, see the Data Sheet at
http://www.netgear.com/images/FVS318N_DS_23Aug1118-36060.pdf.
For best results, place your wireless VPN firewall according to the following general
guidelines:
•Near the center of the area in which your wireless devices will operate.
•In an elevated location such as a high shelf where the wirelessly connected devices have
line-of-sight access (even if through walls).
•Away from sources of interference, such as computers, microwaves ovens, and 2.4-GHz
cordless phones.
•Away from large metal surfaces or water.
•Placing the antennas in a vertical position provides the best side-to-side coverage.
Placing the antennas in a horizontal position provides the best up-and-down coverage.
•If you are using multiple wireless access points such as the wireless VPN firewall, it is
better if access points use different radio frequency channels to reduce interference. The
recommended channel space between adjacent access points is five channels (for
example, use channels 1 and 6, or 6 and 11, or 1 and 11).
•The time it takes to establish a wireless connection can vary depending on both your
security settings and placement. WEP connections can take slightly longer to establish.
Also, WEP encryption can consume more battery power on a notebook computer.

Basic Wireless Configuration and Security
4
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Configure the Country of Operation
The region of operation is nonconfigurable; it is set for the region in which you purchased the
wireless VPN firewall. The selection of the country is limited to the countries in the region in
which you purchased the wireless VPN firewall.
To configure the country settings:
1. Select Network Configuration > Wireless Settings > Radio Settings.The Radio
Settings screen displays:
Figure 1.
2. Specify the country by making a selection from the Country drop-down list.
3. Click Apply to save your settings. The wireless VPN firewall reboots.
Note: Other wireless settings that you can configure on the Radio Settings
screen are explained in the “Configure the Basic Radio Settings”
section in Chapter 4, “Wireless Configuration and Security,” of the
Reference Manual.

Basic Wireless Configuration and Security
5
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Configure WPA+WPA2 with PSK Security
NETGEAR recommends that you configure wireless authentication and encryption to secure
your wireless traffic. WPA+WPA2 with a pre-shared key (PSK) is easy to configure and
should work well in most situations. However, if your network uses 802.11n devices only,
configure WPA2 to enable the 802.11n devices to function at full speed.
To configure WPA+WPA2 with PSK security for the default1 wireless profile:
1. Select Network Configuration > Wireless Settings > Wireless Profiles.The Wireless
Profiles screen displays. (The following figure shows some examples.)
Figure 2.
2. Click the Edit button in the Action column for the default1 wireless profile. The Edit Wireless
Profiles screen displays (see the figure on the next page).
3. From the Security drop-down list, select WPA+WPA2.
The Encryption drop-down list automatically selects TKIP+CCMP, which is the default
encryption setting for WPA+WPA2.
4. From the Authentication drop-down list, select PSK.
5. In the WPA Password field, enter a password (also referred to as a pre-shared key) of at
least 8 characters long.
6. Click Apply to save your settings.

Basic Wireless Configuration and Security
6
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Figure 3.
Note: For other types of security (WEP, WPA, WPA2, RADIUS
authentication) and for the other wireless settings that you can
configure on the Add Wireless Profiles and Edit Wireless Profiles
screens, see the “Configure and Enable Wireless Profiles” section in
Chapter 4, “Wireless Configuration and Security,” of the Reference
Manual.

Basic Wireless Configuration and Security
7
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Configure Wi-Fi Protected Setup for Easy Configuration of
Wireless Clients
Push 'N' Connect using Wi-Fi Protected Setup™ (WPS) allows you to connect computers to a
secure wireless network with WPA or WPA2 wireless security. The wireless VPN firewall
automatically sets security for each computer or device that uses WPS to join the wireless
network. To use WPS, make sure that your wireless devices are Wi-Fi certified and support
WPS. NETGEAR products that use WPS call it Push 'N' Connect.
You can use a WPS button or the wireless router interface method to add wireless computers
and devices to your wireless network. For a list of other Wi-Fi-certified products available
from NETGEAR, go to http://www.wi-fi.org.
To enable WPS and initiate the WPS process on the wireless VPN firewall:
1. Select Network Configuration > Wireless Settings > Wireless Profiles.The Wireless
Profiles screen displays (see Figure 2 on page 5).
2. On the Wireless Profiles screen, to the right of the Wireless Profiles tab, click the WPS
option arrow. The WPS screen displays:
Figure 4.
3. From the Select Wireless Profile SSID drop-down list, select the name of the SSID for which
you want to enable WPS, for example, FVS318N_1 (the default SSID). The wireless profile
with which the SSID is associated needs to be configured for WPA, WPA, or WPA+WPA2
security in order to be displayed as a selection in the drop-down list.
4. From the WPS Status drop-down list, select Enabled to enable the WPS feature.
5. Click Apply to save your changes.

Basic Wireless Configuration and Security
8
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
Note: The Security, Authentication, and Encryption fields are nonconfigurable
fields that are for information only.
6. In the WPS Setup Method section of the screen, use one of the following methods to initiate
the WPS process for a wireless device:
•PIN method:
a. Collect the pin of the wireless device.
b. In the Station PIN field, enter the pin.
c. Click the PIN button.
•Push button configuration (PBC) method:
a. Click the PBC button.
b. Within 2 minutes, press the WPS button on your wireless device to enable the
device to connect to the wireless VPN firewall, or follow the WPS instructions
that came with the device.
With either method, the wireless VPN firewall tries to communicate with the wireless
device, set the wireless security for the wireless device, and allow it to join the wireless
network.
Note: There is no physical WPS push button on the wireless VPN firewall.
Test Wireless Connectivity
After you have configured the wireless VPN firewall as explained in the previous sections,
test your wireless clients for wireless connectivity before you place the wireless VPN firewall
at its permanent position.
To test for wireless connectivity:
1. Configure the 802.11g/n wireless clients so that they all have the same SSID that you
have configured on the wireless VPN firewall, for example, FVS318N_1 (the default
SSID). Make sure that the wireless mode on the wireless VPN firewall supports the
wireless capacity of the wireless clients.
2. Verify that your wireless clients have a link to the wireless VPN firewall.
3. Verify network connectivity by using a browser such as Internet Explorer 7.0 or later or
Mozilla Firefox 4.0 or later to browse the Internet, or check for file and printer access on your
network.
If you have trouble connecting to the wireless VPN firewall, try to connect without security by
selecting OPEN from the Security drop-down list on the Edit Wireless Profiles screen (see
the previous figure) for the profile that you are using.

Basic Wireless Configuration and Security
9
ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N
For More Information
Chapter 4, “Wireless Configuration and Security,” of the Reference Manual provides
information about the following wireless topics:
•Configuring the basic radio settings
•Wireless data security options
•Wireless security profiles, including information about restricting wireless access by MAC
address
•Configuring advanced radio settings