NETGEAR ReadyDATA 5200 User manual

350 East Plumeria Drive
San Jose, CA 95134
USA
December 2012
202-11024-03
ReadyDATA 5200
Hardware Manual

2
NETGEAR ReadyDATA 5200
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product
at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website. For product updates and web
support, visit http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at
http://support.netgear.com/general/contact/default.aspx.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change
without notice. © 2012 All rights reserved.

3
Table of Contents
Chapter 1 Getting Started
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Status and Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2 Expansion Disk Arrays
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3 Maintenance
Front Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Failed Disk Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Add a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Replace a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
System Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Appendix A Warnings and Precautions
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrostatic Discharge (ESD) Precautions . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix B Notification of Compliance

4
1
1. Getting Started
Congratulations on your purchase of a NETGEAR® ReadyDATATM 5200. This ReadyDATA
5200 Hardware Manual describes the physical features of the ReadyDATA 5200. This chapter
includes the following sections:
•Front Panel
•Rear Panel
•Status and Shutdown
•Boot Menu
•Factory Settings
•Technical Specifications
This manual assumes that your ReadyDATA 5200 has been installed in a rack according to the
instructions in the NETGEAR ReadyDATA 5200 Installation Guide.
For detailed information about configuring, managing, and using your ReadyDATA 5200 storage
system, see the ReadyDATA OS Software Manual, which is available on the Resource CD that
came with your storage system and at http://support.netgear.com.

Getting Started
5
NETGEAR ReadyDATA 5200
Front Panel
The following figure shows the front panel of the ReadyDATA 5200 with the optional front
bezel removed.
1
2
Figure 1. ReadyDATA 5200 front panel
1. Drive bays with disk status LEDs
2. Control panel
The following figure shows the control panel in more detail.
1
2
3
4
5
6
7
8
Figure 2. ReadyDATA 5200 control panel
1. Power button
2. Reset button
3. Power LED
4. Ethernet LED
5. Power diagnostic LED
6. Disk activity LED
7. Ethernet LED
8. Information LED

Getting Started
6
NETGEAR ReadyDATA 5200
Each drive bay features a latch that releases the pop-out tray handle, as shown in the
following figure.
1
2
Figure 3. Disk tray handle and release latch
1. Disk tray handle
2. Disk tray release latch
WARNING:
No matter how many hard drives are installed in your system,
ensure that all drive trays remain in the drive bays to maintain
proper airflow.
For more information about adding and replacing disk drives, see Add a Disk on page 23 and
Replace a Disk on page 27.
The ReadyDATA 5200 comes with an front bezel that protects the drive bays with a lockable
cover. You can operate the ReadyDATA 5200 with or without the front bezel.
The following image shows a ReadyDATA 5200 with the front bezel installed.
Figure 4. ReadyDATA 5200 with front bezel installed
For more information about installing and removing the front bezel, see Front Bezel on
page 20.

Getting Started
7
NETGEAR ReadyDATA 5200
Rear Panel
The following figure shows the rear panel of the ReadyDATA 5200.
1
23 4 5678
9
Figure 5. ReadyDATA 5200 rear panel
1. Power supplies
2. PS2 keyboard and mouse ports
3. USB ports
4. RS232 console port
5. VGA monitor port
6. 1-gigabit Ethernet ports with status LED status indicators
7. 10-gigabit Ethernet ports with status LED status indicators
8. SAS output port
9. Maintenance port
Status and Shutdown
You can obtain information about the status of your unit by reviewing the indicators listed in
the following table.
Table 1. Status indicators
Indicator Description
Power LED The LED has these states:
•On.The unit is powered on.
•Off. The unit is powered off.
Disk activity LED The LED has these states:
•On.A disk is active.
•Off. No disk is active.
Power diagnostic LED The LED has these states:
•On.Power failure
•Off. Normal operation

Getting Started
8
NETGEAR ReadyDATA 5200
You can shut down your unit in these ways:
•Using the Power button:
•Preferred shutdown. Press the Power button two times to initiate a graceful
shutdown.
•Forced shutdown. If the unit is hung, press the Power button and hold for 5 seconds
to force a shutdown.
•Using Dashboard. For information about using Dashboard to shut down your unit, see
the ReadyDATA OS Software Manual.
Information LED The LED has these states:
•On.Overheating or fan failure
•Off. Normal operation
Disk LEDs on disk tray with
SAS drives or SSD with
SAS interface
The top LED indicates disk activity as follows:
•Blinking. The disk in the bay is active.
•On. The disk in the bay is inactive.
The bottom LED indicates disk failure, as follows:
•Off. Normal operation
•On. Disk failure
Disk LEDs on disk tray with
SATA drive or SSD with
SATA interface
The top LED indicates disk activity as follows:
•Blinking. The disk in the bay is active.
•Off. The disk in the bay is inactive.
The bottom LED indicates disk failure, as follows:
•Off. Normal operation
•On. Disk failure
Ethernet LEDs (front panel) The Ethernet port LEDs have these states:
•Green. An Ethernet cable is connected.
•Blinking. An Ethernet cable is active.
•Off. An Ethernet cable is disconnected.
1-gigabit Ethernet port
LEDs (rear panel)
The Ethernet port LEDs have these states:
•Amber. The LAN port is operating at 1 Gbps.
•Green. The LAN port is operating at 100 Mbps.
•Off. The LAN port is operating at 10 Mbps.
10-gigabit Ethernet ports
(rear panel)
The Ethernet port LEDs have these states:
•Green. The LAN port is operating at 10 Gbps.
•Amber. The LAN port is operating at 1 Gbps.
Table 1. Status indicators (continued)
Indicator Description

Getting Started
9
NETGEAR ReadyDATA 5200
Boot Menu
Use the boot menu to restart or troubleshoot your ReadyDATA 5200. It has the following boot
modes:
•Normal. Initiates a normal boot process, just like booting using the Power button.
•Factory default. Initiates a reboot process that resets the system to factory settings and
clears all data.
WARNING:
This boot mode erases all data. If your system has data that you
want to save, back it up to another storage device before
performing a factory default reboot.
•OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS
reinstall boot mode when the system crashes and corrupts some configuration files. OS
reinstall boot mode also resets some settings on your unit, such as Internet protocol
settings and the administrator password, to defaults.
•Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode
only when instructed to do so by a NETGEAR technical support representative.
•Memory test. Performs a memory test. The pass or fail result is reported using the unit’s
LEDs. Contact a NETGEAR technical support representative to interpret memory test
results.
To access the boot menu:
1. Power off your unit.
2. With a straightened paper clip, press and hold the Reset button.
3. Press the Power button to power on the unit.
4. Continue to press the Reset button until the power diagnostic LED and the information LED
are both lit.
The step takes approximately 1 minute.
5. Release the Reset button.
6. Press the Reset button within 2 seconds to enter the boot menu.

Getting Started
10
NETGEAR ReadyDATA 5200
7. Press and release the Reset button to scroll through the boot menu options.
Watch the blink pattern of the power diagnostic LED and the information LED. The
following table shows the how the system displays the current option using the power
diagnostic LED and information LED.
Boot Mode Power Diagnostic LED and Information LED Blink Pattern
Normal  
Factory default  
OS reinstall   
Tech support   
Memory test    
Legend:
•Left: Power diagnostic LED
•Right: information LED
•Off: 
•On: 
8. When the power diagnostic LED and information LED indicate the correct boot mode, press
and hold the Reset button for 3 seconds to select that boot mode.
The system confirms the selection by blinking the power diagnostic LED and the
information LED twice, and then begins to boot the system in the selected boot mode.