NETGEAR DG632 - ADSL Modem Router User manual

If software usually logs you in to the Internet, do not run it.
The Internet Explorer Tools Internet Options Connections page should be set to
“Never dial a connection.”
g. Install a filter on each phone device that shares the phone line with your router.
Note: Use one-line filters for connecting additional phones.
2
2Log in to the DG632
Note: Your computer needs to be configured for DHCP. For help with this, see the
Reference Manual or tutorials on the ADSL Modem Router Resource CD.
a. Connect to the router by typing http://192.168.0.1 in the address field of
Internet Explorer or Netscape®Navigator.
b. When prompted, enter admin for the user name and password for the password,
both in lower case letters. After logging in, you will see the menu below.
If you do not see the menu above, click the Setup Wizard link on the upper left
of the main menu.
Start Here
Follow these instructions to set up your ADSL Modem Router.
Before you begin, locate the ADSL configuration information from your Internet Service
Provider (ISP). Also, if you purchased the DG632 in a country where a microfilter is not
included, you must acquire one.
1
1Connect the DG632 to the ADSL Line
ADSL signals degrade phone sound quality. Microfilters block such problems and are
required for each phone or fax. There are two types: one-line microfilters; and two-
line microfilters which include a built-in splitter. Sharing a phone outlet with two
devices requires a splitter.
The procedure below illustrates using a two-line combo
microfilter/splitter. You can accomplish the same result
using a one-line microfilter with a separate phone line
splitter.
a. Insert the filter into the phone outlet and connect
the phone to the phone connector (A).
b. Turn off your computer.
c. Connect the ADSL port (B) of the DG632 to the ADSL connector of the
two-line filter.
Note: Improperly connecting a filter to your DG632 will block ADSL signals
and prevent connecting to the Internet.
d. Connect the Ethernet cable (C) from a LAN port of your DG632 to the
Ethernet adapter in your computer.
e. Plug in the router and verify the following:
The power light is lit after applying power to the router.
The ADSL link light is solid green, indicating a link has been
established to the ADSL network.
f. Now, turn on your computer and verify the following:
The local lights are lit for any connected computers.
ADSL Modem Router DG632
Installation Guide
Phone
DSL
Line
Phone
Phone
DSL
Line
Two-Line Combo
Microfilter/Splitter
One-Line Microfilter Splitter
Phone
DSL
Line
DG632 ADSL Modem Router
B
A
Phone
DSL
Line
DG632 ADSL
Modem Router
C

3
3Connect to the Internet
a. Choose your country. Click Next to let the Setup Wizard detect the type of
Internet connection your have.
b. Follow the steps in the Setup Wizard to input the Internet configuration
parameters from your ISP.
Note: If you were unable to connect to the router, please refer to the
Troubleshooting Chapter in the Reference Manua on the ADSL Modem Router
Resource CD which came with the router.
*201-10090-01*
201-10090-01 February 2004
©2004 NETGEAR, Inc. NETGEAR, the Netgear logo and Everybody's connecting are trademarks or registered
trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and Windows are registered
trademarks of Microsoft Corporation in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is subject to change
without notice. All rights reserved.
Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED
WITH YOUR PRODUCT.
By registering your product at www.NETGEAR.com/register, we can provide you with
faster expert technical support and timely notices of product and software upgrades.