NETGEAR DGN1000 - Wireless-N Router With Built-in DSL... User manual

Verify It All Works
Once everything is connected log in to any one of the Sharedband Routers. In the
menu, down the le side of the page, click on “Status”
This page allows you to see if the Routers connected to the Sharedband service.
Modem Connecon Status checks the connecon to your ISP and the aggregator.
Roung Mode
 No network available: This router is not logged on to the Sharedband Aggre-
gator and is unable to pass trac.
 WAN Only: This router is connected to the aggregaon server.
 Community Only: This router is not directly connected but at least 1 other
Sharedband router is connected.
 WAN and Community: This router and at least 1 other Sharedband router is
connected.
Your able to view the status of all
connected Routers by clicking on
the “Diagnoscs” buon.
More Informaon
Help and Support is available online at: hp://support.sharedband.com
Netgear DG834v4 QIG 4www.sharedband.com
Netgear DGN1000
Quick Install Guide

Hardware Setup
Aer removing the Routers from there packaging and placing them in a suitable
locaon, you are ready to plug them in. The Sharedband Routers can be set up in
two conguraons.
The recommended setup is to connect the Routers
together via an unmanaged switch.
Or plug both Sharedband Routers together
with an Ethernet cable.
Aer connecng the Sharedband Routers together the next step is to connect them
to the phone line. This is done with the thin grey cable found too in the box for each
Router. Please ensure you are only using one microlter per line or connecng di-
rectly to the master socket.
With the Routers connected together and to the phone line they are ready to be
turned on. Plug the power lead into the back of the Router and into the nearest
power outlet.
Soware Setup
Now the Routers are powered on its me to congure the ADSL details. You should
have received the details when your ISP installed your lines or when you signed. If
your unable to locate the details, call your ISP and request the ADSL log in details.
Netgear DG834v4 QIG 2www.sharedband.com
Using a PC connected directly into either one of the Sharedband Routers or the
Switch if you used one, open a web browser and go to this address.
hp://192.168.3.1/
You will be presented with a log in screen. The defaults are:
Username:- “admin”
Password:- “Bonding123”
(You should change the password once setup is complete)
When you have logged in you will noce on the page down the le side is a blue
menu bar. In this menu navigate to the “Basic Sengs” page.
On this page is where enter your ADSL log in details. You will need to select
“PPPoA” from the drop down box (unless your paper work from your ISP dictates
otherwise). Then in the following two boxes enter your ADSL Username and Pass-
word.
Under Internet IP address select
“Get Dynamically From ISP” and
click Apply at the boom of the
page. The Router should now be
connected to the Internet. This will
be indicated by the LEDs on the
front of the router.
Next click on “Conguraon” (under
the Sharedband secon). Ensure
there are details on this page and
the Sharedband service is enabled
before clicking the buon marked
“Save”. When prompted you will be
asked to click “Reboot”. This will restart the router.
Repeat this for the other Routers. Each router has dierent IP address. Which cor-
responds with the number wrien on the base of the Router. For example router
two will be hp://192.168.3.2, Router 3 will be hp://192.168.3.3, etc.
www.sharedband.com 3Netgear DG834v4 QIG