NETGEAR ProSAFE GS724Tv4 User manual

Installation Guide
16-Port and 24-Port Gigabit Ethernet Smart
Managed Pro Switch with 2 SFP Ports
48-Port Gigabit Ethernet Smart Managed Pro
Switch with 2 Copper and 2 Copper/SFP Combo
Ports
Models GS716Tv3, GS724Tv4 and GS748Tv5
Package Contents
• Switch
• Power cord
• Rubber footpads for tabletop installation
• Rack-mount kit for rack installation
• Installation guide
Ethernet cables are not included.
Note: For more information about installation, see the hardware installation
guide, which you can download from https://www.netgear.com/support/.
Congure the switch with a static IP address
Note: If your network uses a DHCP server, this section does not apply. Go
directly to Connect the switch to a network.
If you are using static IP addresses in your network, congure the switch IP
address before you connect the switch to a network.
1. Congure a computer with a static IP address in the 192.168.0.x subnet.
2. Plug the switch into a power outlet and connect your computer to the switch
using an Ethernet cable.
3. Open a web browser and enter 192.168.0.239 in the address bar.
The default IP address of the switch is 192.168.0.239.
A login page displays.
4. Enter password for the password.
The System Information page displays.
5. Select System > Management > IP Conguration.
The IP Conguration page displays.
6. Select the Static IP Address radio button.
7. Enter the static IP address, subnet mask, and default gateway IP address that
you want to assign to the switch.
8. Click the Apply button.
Your settings are saved.
Connect the switch to a network
1. Connect device to the RJ-45 network ports or SFP port on the switch front
panel.
2. Connect an RJ45 port or SFP port on the switch to a network that includes a
DHCP server.
Note: In a small or home ofce network, connect the switch to the LAN port
of a router, that in turn, is connected to an Internet modem.
Congure the switch
You can congure the switch by using the local browser interface, or by installing
the Smart Control Center Utility (see Smart Control Center Utility) on your
Windows-based computer.
Local browser access
1. For initial conguration, open a web browser on a computer that is on the
same network and subnet as the switch and enter the switch’s IP address.
If you are unsure how to determine the IP address of the switch, you can use
the Smart Control Center Utility.
2. A login page displays. Enter password for the password.
The System Information page displays.
3. Congure the switch for your network.
For information about switch conguration, see the user manual for your
switch, which you can download from netgear.com/support/.
Sample connections

NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTL LTD
Floor 1, Building 3, University
Technology Centre
Curraheen Road, Cork
T12EF21, Ireland
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
Support
Thank you for purchasing this NETGEAR product. You can visit
https://www.netgear.com/support/ to register your product, get help, access the
latest downloads and user manuals, and join our community. We recommend
that you use only ofcial NETGEAR support resources.
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
français canadien à https://www.netgear.com/support/download/.
(If this product is sold in Canada, you can access this document in Canadian
French at https://www.netgear.com/support/download/.)
For regulatory compliance information including the EU Declaration of
Conformity, visit https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
Do not use this device outdoors. If you connect cables or devices that are
outdoors to this device, see https://kb.netgear.com/000057103 for safety and
warranty information.
Smart Control Center Utility
The Smart Control Center Utility runs on Windows-based computers. You can
visit netgear.com/support/, enter Smart Control Center in the search box, and
click the Downloads button.
Install the Smart Control Center Utility
Note: The Smart Control Center Utility requires Adobe Air. If Adobe Air is not
detected during Smart Control Center Utility installation, you are prompted to
allow Adobe Air to be installed.
Note: For optimal discovery performance, we recommend that you restart your
computer after installing the Smart Control Center Utility.
Congure the switch with the Smart Control Center Utility
1. Connect the computer to the network.
The computer that is running the Smart Control Center Utility must be on the
same network (with same broadcast domain) as the switch.
2. Click the Discover button.
The Smart Control Center Utility nds Smart Managed Switches on the
network and displays each switch’s MAC address, IP address, and model
number.
If the utility does not discover your switch, verify that the cable connections
are secure and that the computer’s IP address is in the same subnet as the
switch, and click the Discover button.
You might need to temporarily turn off the antivirus program, rewall, or both
on the computer so that the utility can discover the switch.
3. Select the switch that you want to congure.
4. Click the Web Browser Access button.
5. When prompted, enter the password.
The default password is password.
6. Click the Login button.
The System Information page displays.
7. Congure the switch for your network.
For information about switch conguration, see the user manual for your
switch, which you can download from netgear.com/support/.
8. When you are nished with the conguration, return the computer’s antivirus
program and rewall to their usual settings.
Troubleshooting tips
Here are some tips for correcting simple problems that might occur.
• Be sure to power on your computer and switch in the following sequence:
1. Turn on the switch and wait about two minutes.
2. Turn on the computer and connect it to the switch.
• Make sure the Ethernet cables are plugged in.
For each powered-on computer connected to the switch, the corresponding
switch LAN port status LED is lit.
• Make sure the network settings of the computer are correct.
In most cases, computers should be congured to obtain an IP address
through DHCP. If your network uses static IP addresses, be sure that the
switch and computer are congured with valid IP addresses. For more
information, see the software administration manual.
September 2019