NETGEAR ProSafe FS105v2 User manual

Installation Guide
Fast Ethernet Switch
10/100 Mbps FS105 v2/FS108 v2
Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH
YOUR PRODUCT.
By registering your product at www.NETGEAR.com/register, we can provide you with faster
expert technical support and timely notices of product and software upgrades.
NETGEAR, INC.
Support Information
Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support
See Support Information card for other countries.
E-mail: [email protected] (24 x 7 online support)
www.NETGEAR.com
© 2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and
Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the
United States and/or other countries. Microsoft and Windows are registered trademarks of
Microsoft Corporation in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is
subject to change without notice. All rights reserved
July 2004
201-10249-01

Introduction
The NETGEAR®5/8-Port Fast Ethernet Switch Model FS105 v2/FS108 v2 provides you with
a low-cost, reliable, high-performance switch to connect up to five or eight different Ethernet-
enabled devices (such as computers, file servers, print servers, printers, routers and hubs).
You use the FS105 v2/FS108 v2 switch to build a small network that enables you to have 10
Mbps or 100 Mbps access to other devices on the network. Also, with this switch, you can add
extra computers to your cable or DSL router. Unlike a hub that shares its connection with all
devices, the FS105 v2/FS108 v2 switch provides a full, dedicated 100 Mbps (or 10 Mbps)
connection between two devices. If a device has full-duplex capability, the FS105 v2/FS108 v2
switch provides a 200 Mbps (or 20 Mbps) connection.
Ethernet cables come as either straight-through or crossover cables—depending on whether
you’re connecting to a device (computer, server, or printer) or networking equipment (hub,
switch, or router). With the Auto Uplink™ feature, you don’t have to worry about which one
you use. Each port on the FS105 v2/FS108 v2 switch automatically configures itself correctly
when you plug in a device’s cable.
If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7
days a week on the Web (www.NETGEAR.com), by e-mail ([e-mail]) and by
phone (see the provided support information card for phone numbers).
Installation Overview
Estimated Time: 5–10 minutes
1. Unpack the box and verify the contents.
2. Prepare to install the switch.
3. Install the switch and connect the other devices.
Fast Ethernet Switch FS105 v2/FS108 v2
MODEL
FS105
Fast Ethernet Switch
MODEL
FS108
FastEthernetSwitch
PWR
134576
FASTETHERNETSWITCH
FS108
On=Link
Blink=Act
28
100M10M
Auto 10/100Mbps
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch has been suppressed in
accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain
restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch is shielded against the
generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) does not exceed the Class B
limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) respecte les limites de bruits
radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique
du ministère des Communications du Canada.

Introduction
The NETGEAR®5/8-Port Fast Ethernet Switch Model FS105 v2/FS108 v2 provides you with
a low-cost, reliable, high-performance switch to connect up to five or eight different Ethernet-
enabled devices (such as computers, file servers, print servers, printers, routers and hubs).
You use the FS105 v2/FS108 v2 switch to build a small network that enables you to have 10
Mbps or 100 Mbps access to other devices on the network. Also, with this switch, you can add
extra computers to your cable or DSL router. Unlike a hub that shares its connection with all
devices, the FS105 v2/FS108 v2 switch provides a full, dedicated 100 Mbps (or 10 Mbps)
connection between two devices. If a device has full-duplex capability, the FS105 v2/FS108 v2
switch provides a 200 Mbps (or 20 Mbps) connection.
Ethernet cables come as either straight-through or crossover cables—depending on whether
you’re connecting to a device (computer, server, or printer) or networking equipment (hub,
switch, or router). With the Auto Uplink™ feature, you don’t have to worry about which one
you use. Each port on the FS105 v2/FS108 v2 switch automatically configures itself correctly
when you plug in a device’s cable.
If you have a problem with your switch, NETGEAR offers free support 24 hours a day and 7
days a week on the Web (www.NETGEAR.com), by e-mail ([e-mail]) and by
phone (see the provided support information card for phone numbers).
Installation Overview
Estimated Time: 5–10 minutes
1. Unpack the box and verify the contents.
2. Prepare to install the switch.
3. Install the switch and connect the other devices.
Fast Ethernet Switch FS105 v2/FS108 v2
MODEL
FS105
Fast Ethernet Switch
MODEL
FS108
FastEthernetSwitch
PWR
134576
FASTETHERNETSWITCH
FS108
On=Link
Blink=Act
28
100M10M
Auto 10/100Mbps
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch has been suppressed in
accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain
restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and
has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch is shielded against the
generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) does not exceed the Class B
limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR Model FS105 v2/FS108 v2 Fast Ethernet Switch) respecte les limites de bruits
radioélectriques visant les appareils numériques de classe B prescrites dans le Règlement sur le brouillage radioélectrique
du ministère des Communications du Canada.

Unpack the Box and Verify the
Contents
When you open the box, verify that you received everything. The package includes:
• 5/8-Port Fast Ethernet Switch FS105 v2/FS108 v2
• AC power adapter
• Wall-mounting screws
• FS105 v2/FS108 v2 Installation Guide (this document)
• Warranty and support information card
If you don’t have everything listed above, see the support information card for contact
information. If you’re missing the Technical Support information card itself, get contact
information at www.NETGEAR.com in the Customer Service area.
Installation guide,
warranty/registration card
and support
information card Power adapter
Fast Ethernet Switch FS105 v2/FS108 v2
MODEL
FS105
Fast Ethernet Switch
MODEL
FS108
Fast Ethernet Switch
PWR
134 57
6
FASTETHERNETSWITCH
FS108
On=Link
Blink=Act
28
100M 10M
Auto 10/100 Mbps
Wall-mount
hardware
1
1Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,
desk or shelf. The switch comes with wall-mounting screws. You’re welcome to use the screws if
you want to hang the switch in an open space on a wall.
Make sure the selected location is:
• Not in direct sunlight or near a heater or heating vent.
• Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all
sides of the switch.
• Well ventilated (especially if it is in a closet).
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device
you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).
2
2

Unpack the Box and Verify the
Contents
When you open the box, verify that you received everything. The package includes:
• 5/8-Port Fast Ethernet Switch FS105 v2/FS108 v2
• AC power adapter
• Wall-mounting screws
• FS105 v2/FS108 v2 Installation Guide (this document)
• Warranty and support information card
If you don’t have everything listed above, see the support information card for contact
information. If you’re missing the Technical Support information card itself, get contact
information at www.NETGEAR.com in the Customer Service area.
Installation guide,
warranty/registration card
and support
information card Power adapter
Fast Ethernet Switch FS105 v2/FS108 v2
MODEL
FS105
Fast Ethernet Switch
MODEL
FS108
Fast Ethernet Switch
PWR
134 57
6
FASTETHERNETSWITCH
FS108
On=Link
Blink=Act
28
100M 10M
Auto 10/100 Mbps
Wall-mount
hardware
1
1Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,
desk or shelf. The switch comes with wall-mounting screws. You’re welcome to use the screws if
you want to hang the switch in an open space on a wall.
Make sure the selected location is:
• Not in direct sunlight or near a heater or heating vent.
• Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all
sides of the switch.
• Well ventilated (especially if it is in a closet).
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device
you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).
2
2

Install the Switch and Connect the Other
Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device and insert
the other end into one of the Ethernet ports on the switch.
Note: If you have more than 5 or 8 devices to connect to this switch, you must
connect them to a hub or other switch and then connect that hub or switch to this
switch.
3. Connect the power adapter’s cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
The Power light should light up.
The corresponding port number for each connected and powered device should light
when link (connection), and flash when activity occurs.
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.
3
3Troubleshooting
The Power light is not lit
The switch has no power.
• Make sure the power cord is properly connected to the switch.
• Make sure the power adapter is properly connected to a functioning power outlet. If it’s in
a power strip, make sure the power strip is turned on. If the socket is controlled by a light
switch, make sure the switch is in the on position.
• Make sure you are using the NETGEAR power adapter supplied with your switch.
The Link/Activity is not lit for a connected device or stays
on continuously
There’s a hardware connection problem.
• Make sure the cable connectors are securely plugged in at the switch and the device.
• Make sure the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card
or adapter is installed correctly and is working.
• Make sure the cable is less than 328 feet (100 meters).
Technical Specifications
Standards Compatibility: IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet
IEEE 802.3x Flow Control; compatible with Windows®, Mac® OS, NetWare®, Linux®
Data Rate: 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX
10 or 100 Mbps half-duplex
Network Interface: RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface
DC Power: 7.5W max and 7.5V @ 1A DC input
Physical Dimensions: FS105 v2 - W: 94.8 mm (3.73") D: 101 mm (3.98") H: 27 mm (1.06")
FS108 v2 - W: 158 mm (6.22") D: 101 mm (3.98") H: 27 mm (1.06")
Weight: FS105 v2 - 0.275 kg (0.6 lbs); FS108 v2 - 0.49 kg (1.08 lbs)
Operating Temperature: 0 to 40˚ C (32 to 104˚ F)
Operating Humidity: 10% t0 90% relative humidity, non-condensing
Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B,
C-Tick
Safety Agency Approvals for
the Power Adapter: CE mark, Commercial UL listed (UL 1950), TUV licensed (EN 60950), C-Tick
Performance Specifications
Frame Filter Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
Frame Forward Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
Network Latency: 100 Mbps to 100 Mbps: 20 µs max
(using 64-byte packets)
Address Database Size: 1024 MAC addresses
Addressing: 48-bit MAC address
Queue Buffer: FS105 v2 - 64 kilobytes; FS108 v2 - 96 kilobytes

Install the Switch and Connect the Other
Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device and insert
the other end into one of the Ethernet ports on the switch.
Note: If you have more than 5 or 8 devices to connect to this switch, you must
connect them to a hub or other switch and then connect that hub or switch to this
switch.
3. Connect the power adapter’s cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
The Power light should light up.
The corresponding port number for each connected and powered device should light
when link (connection), and flash when activity occurs.
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.
3
3Troubleshooting
The Power light is not lit
The switch has no power.
• Make sure the power cord is properly connected to the switch.
• Make sure the power adapter is properly connected to a functioning power outlet. If it’s in
a power strip, make sure the power strip is turned on. If the socket is controlled by a light
switch, make sure the switch is in the on position.
• Make sure you are using the NETGEAR power adapter supplied with your switch.
The Link/Activity is not lit for a connected device or stays
on continuously
There’s a hardware connection problem.
• Make sure the cable connectors are securely plugged in at the switch and the device.
• Make sure the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card
or adapter is installed correctly and is working.
• Make sure the cable is less than 328 feet (100 meters).
Technical Specifications
Standards Compatibility: IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet
IEEE 802.3x Flow Control; compatible with Windows®, Mac® OS, NetWare®, Linux®
Data Rate: 100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX
10 or 100 Mbps half-duplex
Network Interface: RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface
DC Power: 7.5W max and 7.5V @ 1A DC input
Physical Dimensions: FS105 v2 - W: 94.8 mm (3.73") D: 101 mm (3.98") H: 27 mm (1.06")
FS108 v2 - W: 158 mm (6.22") D: 101 mm (3.98") H: 27 mm (1.06")
Weight: FS105 v2 - 0.275 kg (0.6 lbs); FS108 v2 - 0.49 kg (1.08 lbs)
Operating Temperature: 0 to 40˚ C (32 to 104˚ F)
Operating Humidity: 10% t0 90% relative humidity, non-condensing
Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B,
C-Tick
Safety Agency Approvals for
the Power Adapter: CE mark, Commercial UL listed (UL 1950), TUV licensed (EN 60950), C-Tick
Performance Specifications
Frame Filter Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
Frame Forward Rate: 14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
Network Latency: 100 Mbps to 100 Mbps: 20 µs max
(using 64-byte packets)
Address Database Size: 1024 MAC addresses
Addressing: 48-bit MAC address
Queue Buffer: FS105 v2 - 64 kilobytes; FS108 v2 - 96 kilobytes

Installation Guide
Fast Ethernet Switch
10/100 Mbps FS105 v2/FS108 v2
Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH
YOUR PRODUCT.
By registering your product at www.NETGEAR.com/register, we can provide you with faster
expert technical support and timely notices of product and software upgrades.
NETGEAR, INC.
Support Information
Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support
See Support Information card for other countries.
E-mail: [email protected] (24 x 7 online support)
www.NETGEAR.com
© 2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and
Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the
United States and/or other countries. Microsoft and Windows are registered trademarks of
Microsoft Corporation in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is
subject to change without notice. All rights reserved
July 2004
201-10249-01