NETGEAR ProSAFE S3300-52X User manual

Installation Guide
28-Port and 52-Port Gigabit Ethernet Stackable
Smart Managed Pro Switch with 2 Copper 10G
and 2 SFP+ 10G Ports
Model S3300-28X and S3300-52X
28-Port and 52-Port Gigabit Ethernet PoE+
Stackable Smart Managed Pro Switch with 24 and
48 PoE+ Ports, 2 Copper 10G and 2 SFP+ 10G
Ports
Model S3300-28X-PoE+ and S3300-52X-PoE+
Package contents
• Switch
• Power cord
• Rubber footpads for tabletop installation
• Rack-mount kit for rack installation
• Installation guide
Note: For more information about installation, see the hardware installation guide,
which you can download from netgear.com/support/.
Connect the switch to your network
Note: If you are using static IP addresses in your network, congure the
switch IP address before you connect the switch to a network. See Congure
the switch with a static IP address.
1. Connect network devices to the ports on the switch.
2. Connect one port on the switch to a network router that provides Internet
connectivity.
3. Power on the switch.
Check the PoE status
PoE+ power is provided by the S3300-28X-PoE+ and S3300-52X-PoE+ switch on
all ports. The switch can supply up to 30W PoE+ (IEEE 802.3at) to each port, with a
PoE power budget of 195W and 390W across all active PoE+ ports.
The PoE Max LED indicates the status of the PoE budget on the switch:
• Off. Sufcient. More than 7W of PoE power is available.
• Solid yellow. Less than 7W of PoE power is available.
• Blinking yellow. At least once during the previous two minutes, less than 7W
of PoE power was available.
Discover and register the switch
If the switch is connected to a WiFi router or access point and to the Internet, you can use
the NETGEAR Insight app to discover the switch in your network, register the switch with
NETGEAR, and activate your warranty.
1. On your mobile device, visit the app store, search for NETGEAR Insight, and
download the latest version of the app.
2. Connect your mobile device to the same WiFi network as the switch.
3. Open the NETGEAR Insight app.
4. If you did not set up a NETGEAR account, tap Create NETGEAR Account and follow
the onscreen instructions.
5. Enter the email address and password for your account and tap LOG IN. After you log
in to your account, the switch displays in the devices list.
6. Tap + in the upper right corner.
7. Either use the camera on your phone to scan the serial number bar code located on
the bottom of the switch, or enter the serial number.
8. Tap Go.
9. Follow the onscreen instructions to add your switch to a network location.
10. The switch is registered and added to your NETGEAR account. You can now view and
monitor the switch.
Note: Model S3300 Smart Managed Pro switches are not Insight manageable.

NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTERNATIONAL LTD
Floor 1, Building 3
University Technology Centre
Curraheen Road, Cork,
T12EF21, Ireland
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo
are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
Support
Thank you for purchasing this NETGEAR product. You can visit
https://www.netgear.com/support/ to register your product, get help, access the
latest downloads and user manuals, and join our community. We recommend that
you use only ofcial NETGEAR support resources.
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en
français canadien à https://www.netgear.com/support/download/.
(If this product is sold in Canada, you can access this document in Canadian
French at https://www.netgear.com/support/download/.)
For regulatory compliance information including the EU Declaration of
Conformity, visit https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
Do not use this device outdoors. If you connect cables or devices that are
outdoors to this device, see https://kb.netgear.com/000057103 for safety and
warranty information.
August 2019
Congure the switch with a static IP address
Note: If your network uses a DHCP server, this section does not apply.
If you are using static IP addresses in your network, congure the switch IP
address before you connect the switch to a network.
1. Congure a computer with a static IP address in the 192.168.0.x subnet.
2. Power on the switch, and connect your computer to the switch using an
Ethernet cable.
3. Open a web browser and enter 192.168.0.239 in the address bar.
(The default IP address of the switch is 192.168.0.239.)
A login page displays.
4. Enter password for the password.
The System Information page displays.
5. Select System > Management > IP Conguration. Select the Static IP
Address radio button.
6. Enter the static IP address, subnet mask, and default gateway IP address that
you want to assign to the switch and click the Apply button.
Your settings are saved.
Congure the switch
To congure the switch either:
• Use the local browser browser–based interface.
• Install the NETGEAR Switch Discovery Tool on your Mac or a 64-bit
Windows-based computer.
• Install the Smart Control Center utility on your Windows-based computer.
Access the local browser interface
1. For initial conguration, open a web browser on a computer that is on the
same network and subnet as the switch and enter the switch’s IP address.
If you are unsure how to determine the IP address of the switch, you can use
the Smart Control Center utility.
2. A login page displays. Enter password for the password.
The System Information page displays.
3. Congure the switch for your network.
For information about switch conguration, see the user manual for your
switch, which you can download from netgear.com/support/.
Other discovery and conguration methods
The NETGEAR Switch Discovery Tool and the Smart Control Center utility let you
discover the IP address and congure the switch.
• NETGEAR Switch Discovery Tool. You can use a Mac or a 64-bit Windows-
based computer on the same network as the switch. To download this tool,
visit netgear.com/support/product/netgear-switch-discovery-tool.aspx.
• Smart Control Center utility. You can use a Windows-based computer on
the same network as the switch. To download this utility, visit netgear.com/
support/product/SCC.
Troubleshooting tips
Here are some tips for correcting simple problems that might occur.
• Be sure to power on your computer and switch in the following sequence:
a. Turn on the switch and wait about two minutes.
b. Turn on the computer and connect it to the switch.
• Make sure the Ethernet cables are plugged in.
For each powered-on computer connected to the switch, the corresponding
switch LAN port status LED is lit.
• Make sure the network settings of the computer are correct.
In most cases, computers should be congured to obtain an IP address
through DHCP. If your network uses static IP addresses, be sure that the switch
and computer are congured with valid IP addresses. For more information,
see the user manual.