netvox R315 Series User manual

Wireless Multi Sensor Device
R315 Series
User Manual
Copyright©Netvox Technology Co., Ltd.
This document contains proprietary technical information which is the property of
NETVOX Technology and is issued in strict confidential and shall not be disclosed to
others parties in whole or in parts without written permission of NETVOX Technology.
The specifications are subjected to change without prior notice.

1
Table of Content
1. Introduction.............................................................................................2
2. Appearance..............................................................................................3
3. R315 Series Combinations .......................................................................4
4. Main Features..........................................................................................4
5. R315 Series Sensor Function....................................................................5
5.1 Sensor Function................................................................................5
5.2 Command Rules................................................................................8
6. Set up Instruction ..................................................................................10
7. Data Report ...........................................................................................12
7.1 Example of ReportDataCmd ...........................................................13
7.2 Example of ConfigureCmd ..............................................................14
7.2.1 Min Time / MaxTime / Data Variation ................................................................................................. 15
7.2.2 PIR Setting ........................................................................................................................................... 16
7.2.3 Vibration Sensor Sensitivity Setting..................................................................................................... 17
7.2.4 Disable Time and Detection Time........................................................................................................ 18
7.2.5 Buzzer Beep Duration.......................................................................................................................... 19
7.2.6 Dry Contact Point Out Type ................................................................................................................. 19
7.2.7 Vibration / Tilt Sensor Restore Function.............................................................................................. 20
7.2.8 Dry Contact Resend Time Function...................................................................................................... 21
7.2.9 Button Press Time................................................................................................................................ 22
7.2.10 ConfigDryContactINTriggerTime........................................................................................................ 23
7.3 Example for MinTime/MaxTime logic.............................................23
8. Installation.............................................................................................25
9. Other Combinations of R315 .................................................................26
10. Important Maintenance Instruction ....................................................28

2
1. Introduction
R315 series is a multi-sensor device of Netvox's Class A type device based on LoRaWAN open protocol. It can be
mixed with temperature and humidity, illuminance, door magnetism, internal vibration, external vibration,
infrared detection, emergency button, tilt detection, water leakage detection, glass break, seat occupancy
detection, dry contact in, DO out related functions (up to 5 types of sensors can be compatible at the same
time), and compatible with LoRaWAN protocol.
LoRa Wireless Technology:
LoRa is a wireless communication technology dedicated to long distance and low power consumption.
Compared with other communication methods, LoRa spread spectrum modulation method greatly increases to
expand the communication distance. Widely used in long-distance, low-data wireless communications. For
example, automatic meter reading, building automation equipment, wireless security systems, industrial
monitoring. Main features include small size, low power consumption, transmission distance, anti-interference
ability and so on.
LoRaWAN:
LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure interoperability between
devices and gateways from different manufacturers.

3
Function Key
Indicator
2. Appearance
PIR
Internal Sensor
- PIR
- Emergence Button
- Light Sensor
- Temperature and humidity Sensor
- Vibration Sensor (built-in)
- Tilt Sensor
External Sensor
- Reed Switch
- Water Leak
- Dry Contact In
- DO out (3V)
- Vibration Sensor (external)
- Seat Occupancy
- Glass Break
Light Sensor
Emergence Button

4
3. R315 Series Combinations
Model
TH
Light
Internal
Vibration
PIR
Emergency
Button
Tilt
Water
Leak
Reed
Switch
Dry
Contact
In
DO Out
External
Vibration
Glass
Break
Seat
R31501
V
V
V
V
V
R31502
V
V
V
V
V
R31503
V
V
V
V
V
R31504
V
V
V
V
V
R31505
V
V
V
V
V
R31506
V
V
V
V
V
R31507
V
V
V
V
V
R31508
V
V
V
V
V
R31509
V
V
V
V
V
R31510
V
V
V
V
V
Note:
1. By default, the factory is not equipped with a buzzer as standard
2. After the external port is configured, the corresponding sensor should be connected according to the
configuration. If the corresponding sensor is not connected, the reported status should be ignored
4. Main Features
➢Compatible with LoRaWAN
➢2 sections of 3V CR2450 button battery power supply
➢Simple operation and setting
➢Compatible with LoRaWAN Class A
➢Frequency hopping spread spectrum technology
➢Configuration parameters can be configured through third-party software platforms, data can be read and
alarms can be set via SMS text and email (optional)
➢Available third-party platform: Actility / ThingPark, TTN, MyDevices/Cayenne
➢Low power consumption and long battery life

5
5. R315 Series Sensor Function
5.1 Sensor Function
(1) Temperature and humidity Sensor
Detection of temperature and humidity in ambient air.
Temperature unit: 0.01°C, signed value
Humidity unit: 0.5%
(2) Light Sensor
Detection of ambient light illuminance and detection range 0~3000 lux.
Illuminance unit: 1 lux
(3) Reed Switch
Detect the opening and closing state of the reed switch.
Open: report 1
Close: report 0
➢If the DO out function is available, after the reed switch is turned on, a signal will be output to the DO out.
(it is off by default)
➢Configurable resend function.
➢The reed switch needs to be fixed when used, such as the double sided tape.
(4) Internal Vibration Sensor
Detect the vibration state of the current device body.
Vibration: report 1
Static: report 0
➢The sensitivity is configurable, the sensitivity configuration level is 0x00~0x0A, default sensitivity is 0x05.
➢The restore function can be configured.
(5) External Vibration Sensor
Detection of external sensor vibration status.
Vibration: report 1
Static: report 0
➢The sensitivity is configurable, the sensitivity configuration level is 0x00~0xFE, default sensitivity is 0x14.
➢ Configurable restore function.

6
➢External vibration sensor needs to be fixed when using, such as double sided tape.
(6) PIR
Detect infrared
There are people: report 1
There are no people: report 0
➢Report follows IR disable time and IR detection time rules.
➢If there is a DO out function, PIR will output a signal to DO out after detecting it. (it is off by default)
(7) Emergency Button
Press the emergency button to report the alarm status.
No alarm = report 0
Alarm = report 1
➢Configurable press duration.
(8) Tilt Sensor
The sensor adopts 45 °tilt detection, and the initial state of the device is vertical,
When the inclination angle changes by more than 45 °(in either direction), a tilt alarm will be sent
immediately.
Device tilt: report 1
Device recovery: report 0
➢Configurable resend function
➢If there is a DO out function, Tilt sensor will output a signal to DO out after detecting it.
(it is off by default)
➢When the inclination is greater than 45 °~180 °, alarm will be sent.
The following is the working diagram of the sensor:
Note:

7
Please place it vertically for use, otherwise the test result may be affected
(9) Water Leak
When the leak sensor is immersed in water,it will immediately issue a report, leaking status:1.
When the leak sensor is out of the immersion state, a report is issued immediately, with no water leakage
status: 0
➢ If the DO out function is available, a signal will be output to the DO out after the water leakage is triggered. (it
is off by default)
(10) Dry Contact IN
When the dry contact is disconnected (open circuit): Report 0
When dry contact is connected (short circuit): Report 1
➢If the DO out function is available, a signal will be output to the DO out after the dry
contact in is triggered.
(11) Seat Occupancy
When the seat occupancy sensor detects that the occupancy status has changed,
The seat is occupied: report 1
The seat is not occupied: report 0
➢ Report follows IR disable time and IR detection time rules.
(12) DO OUT
When PIR、emergency button alarm、reed switch、leakage、tilt、internal vibration、external vibration、
glass break=1 (Alarm), then DO OUT = 1 ( Hight level , enable)
➢DO OUT default is 0. (Low level, disable)
➢It can be turned on by command, and the output time can be configured by command.
➢Only one DO OUT function can be enabled at most.
(13) Glass Break
No broken glass detected: report 0
Broken glass detected: report 1
➢If the DO out function is available, a signal will be output to the DO out after the glass is
broken. (it is off by default)
(14) Buzzer (optional)

8
The functions of water leak, reed switch and glass break detection will trigger the buzzer to sound. The
default time of the buzzer is 15s, which can be configured through the command. As the buzzer sounds more
power consuming, which affects the service life of the battery, it is recommended that the longest buzzer
time should not exceed 3min.
5.2 Command Rules
5.2.1 IRDisableTime and IRDetectionTime
IRDisableTime and IRDetectionTime are parameters defining PIR/seat occupancy behavior after it detects
motion.
IRDisableTime is the sampling period while IRDetectionTime is detecting period.
By default, IRDisableTime is 30 seconds and IRDetectionTime is 5 minutes.
When PIR/seat occupancy is triggered, PIR/seat occupancy will be turned off for first 70% of IRDisableTime to
save power and then turned on for rest 30% of IRDisableTime.
➢If living creature is detected during the rest 30% of IRDisableTime, the IR delay time will be extended for
another IRDetectionTime until no infrared signal is detected.
➢If no living creature is detected during IRDetectionTime, PIR/seat occupancy will report un-occupied along
with other sensor status.
Example1:
While IRDetectionTime is 60 s and IRDisableTime is 30 s, no living creature is detected after triggered.
PIR/seat occupancy will report un-occupied after 60 secs (IRDetectTime).
Example2:
IRDisableTime = 30 s
IRDetectionTime = 60 s
IRDisableTime = 30 s
Turn on for 9 s
(30%)
Turn off for 21 s.
(70%)
Turn off for 21 s.
(70%)
Turn on for 9 s
(30%)

9
While IRDetectionTime is 60 secs and IRDisableTime is 30 secs, living creature is detected during 25th sec.
PIR/seat occupancy will restart IR detect procedure(IRDetectionTime).
No living creature is detected during next IRDetectionTime and PIR/seat occupancy therefore report un-occupied.
5.2.2 Restore Rereport
➢ Applicable sensor: Internal vibration sensor, external vibration sensor
RestoRereportSet = 0x00, only sends vibration data
RestoRereportSet = 0x01, sends vibration data and vibration stop data,
When the light sensor is disable, the vibration stop data is sent 10 seconds after the vibration stops.
When the light sensor is enable, the stop vibration stop data will be sent 30 seconds after the vibration
stops
5.2.3 LastMessageResendtime
➢ Applicable sensor: Reed switch, tilt sensor
When the device is triggered quickly, additional data can be sent
Resendtime=0, When the reed switch is closed immediately after magnetic opening, it will only receive reed
switch status =1
Resendtime=3, Close the reed switch as soon as it is opened, and you will receive reed switch status =1,
It will be received after 3 seconds reed switch status =0
Resendtime = 0x00 or 0xFF, No additional data will be sent
Resendtime = 0x03 to 0xFE, The device will send data after triggering, and then supplement the last status
data after 3-254s
IRDetectionTime = 60 s
IRDisableTime = 30 s
IRDisableTime = 30 s
Turn on for 9 s
(30%)
Turn off for 21 s.
(70%)
25 s
Turn off for 21 s.
(70%)
Turn on for 9 s
(30%)
Turn on for 9 s
(30%)

10
6. Set up Instruction
--- On/Off ---
Power on
Insert batteries.
Turn on
Press function key till green indicator flashes once.
Turn off (Restore to factory setting)
Press the function key for more than 8 seconds, and the green indicator light
will flash continuously. Release the key after the flash starts, and the device
will automatically shut down after the flash ends.
(Indicator light display: the indicator light will flash once every 2s to prompt
the current pressing duration)
Power off
Remove Batteries.
Note:
Please put the battery into the battery holder according to the positive and negative electrodes of the
battery, and push back the back cover.
Two CR2450 button batteries are required to supply power at the same time.
3. Remove and insert the battery; the device memorizes previous on/off state by default.
4. On/off interval is suggested to be about 10 seconds to avoid the interference of capacitor inductance and other
energy storage components.
5. Press function key and insert batteries at the same time; it will enter engineer testing mode.
--- Network Joining ---
Never joined the network
Turn on the device to search the network.
The green indicator stays on for 5 seconds: success
The green indicator remains off: fail
Had joined the network
Turn on the device to search the previous network.
The green indicator stays on for 5 seconds: success
The green indicator remains off: fail
Fail to join the network
(when the device is on)
Suggest to check the device verification information on the gateway with
your platform server provider.

11
--- Function Key ---
Press the function key for more than
8 seconds
Restore to factory setting / Turn off
The green indicator flashes for 20 times: success
The green indicator remains off: fail
Press once
The device is in the network: green indicator flashes once and sends a report
The device is not in the network: green indicator remains off
Press and hold the key for 2s
Turn off the buzzing buzzer
*Applicable to device with buzzer
Press and hold the key for 4s
Turn off the infrared detection function
*Applicable to device with PIR
--- Sleeping Mode ---
The device is on and in the
network
Sleeping period: Min Interval.
When the reportchange exceeds setting value or the state changes:
send a data report according to Min Interval.
--- Low Voltage Warning ----
Low Voltage
2.4V

12
7. Data Report
When the device is turned on, it will immediately send a version package.
➢ Default setting:
Max Interval: 0x0E10 (3600s)
Min Interval: 0x0E10 (3600s)
Battery Change: 0x01 (0.1V)
Temperature Change: 0x0064 (1°C), Signed 2 Bytes, unit: 0.01°C
Humidity Change: 0x14 (10%), 1 Byte, unit: 0.5%
Illuminance Change: 0x64 (100 lux), 1 Byte, unit:1 lux
Internal Shock Sensor Sensitivity: 0x05 // Internal Vibration Sensor, Sensitivity Range:0x00-0x0A
External Shock Sensor Sensitivity: 0x14 // External Vibration Sensor, Sensitivity Range:0x00-0xFE
(The smaller the number, the more sensitive)
Disabletime: 0x001E (30s) // PIR and Seat Occupancy (DisableTime must ≥ 5s)
Detechtime: 0x012C (300s) // PIR and Seat Occupancy (DectionTime must ≥ DisableTime)
AlarmONTime: 0x0F (15s) // Buzzer
Dry Contact Point Out Type: 0x00 (Normally Open)
RestoreReportSet: 0x00 (DO NOT report when sensor restore) // Vibration Sensor
➢ The device report interval will be programmed based on the default firmware.
➢ The interval between two reports must be the minimum time.
➢ The reported data is decoded by the Netvox LoRaWAN Application Command document and
http://cmddoc.netvoxcloud.com/cmddoc

13
7.1 Example of ReportDataCmd
FPort：0x06
Bytes
1
1
1
Var(Fix=8 Bytes)
Version
DeviceType
ReportType
NetvoxPayLoadData
Version – 1 byte –0x01——the Version of NetvoxLoRaWAN Application Command Version
Device Type – 1 byte – Device Type of Device
The device type is listed in Netvox LoRaWAN Application Devicetype.doc
ReportType – 1 byte –the presentation of the NetvoxPayLoadData, according the device type
NetvoxPayLoadData– Fixed bytes (Fixed =8bytes)
Device
Device
Type
Report
Type
NetvoxPayLoadData
0xD2
0x01
Battery
(1Byte)
unit:0.1V
FunctionEnableBits
(2Bytes)
Bit0: THSensor
Bit1: LightSensor
Bit2: PIRSensor
Bit3: EmergenceButton
Bit4:TiltSensor
Bit5: InternalContactSwitch
Bit6:ExternalContactSwitch
Bit7:InternalShockSensor
Bit8: ExternalShockSensor
Bit9:ExternalDryContactPointIN
Bit10: DryContactPointOut
Bit11: ExternalWaterLeakSenor
Bit12:ExternalSeatSensor
Bit13:ExternalGlassSensor
Bit14-Bit15: Reserved
When Bit is 1,
the function is enabled
BinarySensorReport
(2bytes)
Bit0: PIRSensorState
(0b01_ON,0b00_OFF)
Bit1: EmergenceButtonAlarmState
(0b01_Alarm,0b00_NoAlarm)
Bit2:TiltSensorState
(0b01_ON,0b00_OFF)
Bit3:InternalContactSwitchSensorState
(0b01_ON,0b00_OFF)
Bit4:ExternalContactSwitchSensorState
(0b01_ON,0b00_OFF)
Bit5: InternalShockSensorState
(0b01_ON,0b00_OFF)
Bit6: ExternalShockSensorState
(0b01_ON,0b00_OFF)
Bit7: ExternalDryContactPointINState
(0b01_ON,0b00_OFF)
Bit8: ExternalWaterLeakSenorState
(0b01_ON,0b00_OFF)
Bit9: ExternalSeatSenorState
(0b01_ON,0b00_OFF)
Bit10: ExternalGlassSenorState
(0b01_ON,0b00_OFF)
Bit11~Bit14:
(Reserved Fixed 0b00)
Bit15:HeartBeat
(0b01_Heartbeat,0b00_NOTHeartbeat)
Temperature
(Signed 2Bytes)
unit:0.01°C
When THSensor
Bit is 0 in the
FunctionEnableBits,
the filed is fixed
0xFFFF
Humidity
(1Byte)
unit:0.5%
When THSensor
Bit is 0 in the
FunctionEnableBits,
the filed is fixed 0xFF
0x02
Battery
(1Byte)
unit:0.1V
Illuminance
(2Bytes,unit:1Lux)
Reserved
(5Bytes,fixed 0x00)
Note:
The payload with report type=0x02 only present when light sensor is enabled in FunctionEnableBits.
When the light sensor function is enabled, two packets of data will be reported.

14
The DeviceType are 0x01 and 0x02, and the interval between the two packets of data is 10s.
If the light sensor function is disabled, only one packet of data will be reported each time.
Uplink: 01D2011C084900120ADC6A
1st byte (01): Version
2nd byte (D2): DeviceType 0XD2 － R315 Series
3rd byte (01): Report Type
4th byte (1C): Battery－2.8v , 1C Hex=28 Dec 28*0.1v=2.8v
5th 6th byte (0849): FunctionEnableBits, 0x0849 = 0000 1000 0100 1001 (Bin) //Bit 0,3,6,11 = 1 (enable)
Bit0: Temperature and Humidity
Bit3: Emergence Button
Bit6: Reed Switch
Bit11: Water Leak
7th 8th byte (0012): BinarySensorReport, 0x0012 = 0000 0000 0001 0010 (Bin) //Bit 1,4 = 1 (ON)
Bit1: Emergence Button Alarm
Bit4: Reed Switch Alarm
9th 10th byte (0ADC): Temperature－27.8°C, ADC Hex=2780 Dec 2780*0.01°C =27.80°C
11th byte (6A): Humidity－53%, 6A Hex=106 Dec 106*0.5% =53%
Note:
1. Battery (1Byte, unit:0.1V): Bit7 represent low battery, Bit6-0 represent battery voltage
2. Temperature (Signed 2Bytes, unit:0.01°C): Negative numbers are represented by 2's complement
7.2 Example of ConfigureCmd
FPort：0x07
Bytes
1
1
Var (Fix =9 Bytes)
CmdID
DeviceType
NetvoxPayLoadData
CmdID– 1 byte
DeviceType– 1 byte – Device Type of Device
NetvoxPayLoadData– var bytes (Max=9bytes)

15
7.2.1 Min Time / MaxTime / Data Variation
FPort：0x07
Description
Cmd
ID
Device
Type
NetvoxPayLoadData
Config
ReportReq
0x01
0xD2
MinTime
(2bytes)
Unit:s)
MaxTime
(2bytes)
Unit:s
Battery
Change
(1byte)
Unit:0.1v
Temperature
Change
(2bytes)
Unit:0.01°C
Humidity
Change
(1byte)
Unit:0.5 %
Illuminance
Change
(1byte)
Unit：1Lux
Config
ReportRsp
0x81
Status
(0x00_success)
Reserved
(8Bytes,Fixed 0x00)
ReadConfig
ReportReq
0x02
Reserved
(9Bytes,Fixed 0x00)
ReadConfig
ReportRsp
0x82
MinTime
(2bytes)
Unit:s
MaxTime
(2bytes)
Unit:s
Battery
Change
(1byte)
Unit:0.1v
Temperature
Change
(2bytes)
Unit:0.01°C
Humidity
Change
(1byte)
Unit:0.5 %
Illuminance
Change
(1byte)
Unit：1Lux
1. Configure device parameters MinTime = 1min, MaxTime = 1min, BatteryChange = 0.1v,
TemperatureChange = 10°C, HumidityChange = 20%, Illuminancechange = 100lux
Downlink: 01D2003C003C0103E82864
1st byte (01): CMD ID
2nd byte (D2): DeviceType 0XD2 － R315 Series
3rd 4th byte (003C): Min Time, 003C(Hex)=60(Dec), 60s
5th 6th byte (003C): Max Time, 003C(Hex)=60(Dec), 60s
7th byte (01): Battery Change, 0.1v
8th 9th byte (03E8): Temperature Change, 03E8(Hex) = 1000(Dec), 1000*0.01°C=10°C
10th byte (28): Humidity Change, 28(Hex)=40(Dec), 40*0.5%=20%
11th byte (64): Illuminance Change, 64(Hex)=100(Dec), 100*1 lux=100 lux
Response:
81D2000000000000000000（Configuration success）
81D2010000000000000000（Configuration failure）

16
2. Read Configuration:
Downlink: 02D2000000000000000000
Response:
82D2003C003C0103E82864（Current configuration）
7.2.2 PIR Setting
FPort：0x07
Description
Cmd
ID
Device
Type
NetvoxPayLoadData
SetPIR
EnableReq
0x03
0xD2
PIREnable
(1Byte,0x00_Disable,0x01_Enable)
Reserved
(8Bytes,Fixed 0x00)
SetPIR
EnableRsp
0x83
Status
(0x00_success)
Reserved
(8Bytes,Fixed 0x00)
GetPIR
EnableReq
0x04
Reserved
(9Bytes,Fixed 0x00)
GetPIR
EnableRsp
0x84
PIREnable (1Byte)
0x00_Disable,0x01_Enable
Reserved
(8Bytes,Fixed 0x00)
1. Disable PIR detection
Downlink: 03D2000000000000000000
2. Enable PIR detection
Downlink: 03D2010000000000000000
Response:
83D2000000000000000000（Configuration success）
83D2010000000000000000（Configuration failure）

17
7.2.3 Vibration Sensor Sensitivity Setting
FPort：0x07
Description
Cmd
ID
Device
Type
NetvoxPayLoadData
SetShockSensor
SensitivityReq
0x05
0xD2
InternalShockSensor
Sensitivity (1Byte)
0xFF represent disable
ShockSensor
ExternalShockSensor
Sensitivity (1Byte)
0xFF represent disable
ShockSensor
Reserved
(7Bytes,Fixed 0x00)
SetShockSensor
SensitivityRsp
0x85
Status
(0x00_success)
Reserved
(8Bytes,Fixed 0x00)
GetShockSensor
SensitivityReq
0x06
Reserved
(9Bytes,Fixed 0x00)
GetShockSensor
SensitivityRsp
0x86
InternalShockSensor
Sensitivity (1Byte)
0xFF represent disable
ShockSensor)
ExternalShockSensor
Sensitivity (1Byte)
0xFF represent disable
ShockSensor)
Reserved
(7Bytes,Fixed 0x00)
Set Internal Vibration Sensor Sensitivity = 3, External Vibration Sensor Sensitivity = 25
Downlink: 05D2031900000000000000 //19(Hex)=25(Dec)
Response:
85D2000000000000000000（Configuration success）
85D2010000000000000000（Configuration failure）
Note:
1. Internal Vibration Sensor Sensitivity default is 0x05, sensitivity range: 0x00 - 0x0A (0~10)
2. External Vibration Sensor Sensitivity default is 0x14, sensitivity range: 0x00 - 0xFE (0~254)
3. 0xFF represent disable vibration sensor
4. The smaller the number, the more sensitive

18
7.2.4 Disable Time and Detection Time
FPort：0x07
Description
Cmd
ID
Device
Type
NetvoxPayLoadData
SetIR
DisableTImeReq
0x07
0xD2
IRDisableTime
(2bytes Unit:s)
IRDetectionTime
(2bytes Unit:s)
SensorType(1Byte)
0x00_PIRSensor
0x01_SeatSensor
Reserved
(4Bytes,Fixed
0x00)
SetIR
DisableTImeRsp
0x87
Status
(0x00_success)
Reserved
(8Bytes,Fixed 0x00)
GetIR
DisableTImeReq
0x08
SensorType (1Byte)
0x00_PIRSensor
0x01_SeatSenso
Reserved
(8Bytes,Fixed 0x00)
GetIR
DisableTImeRsp
0x88
IRDisableTime
(2bytes Unit:s)
IRDetectionTime
(2bytes Unit:s)
Reserved
(5Bytes,Fixed 0x00)
1. Set PIR Sensor IRDisableTime=30s, IRDetectionTime=60s
Downlink: 07D2001E003C0000000000 //1E(Hex)=30(Dec), 3C(Hex)=60(Dec)
2. Set Seat sccupancy sensor IRDisableTime=30s, IRDetectionTime=90s
Downlink: 07D2001E005A0100000000 //1E(Hex)=30(Dec), 5A(Hex)=90(Dec)
Response:
87D2000000000000000000（Configuration success）
87D2010000000000000000（Configuration failure）
Note:
1. DetectionTime must ≥ IRDisableTime
2. DisableTime must ≥ 5s

19
7.2.5 Buzzer Beep Duration
FPort：0x07
Description
Cmd
ID
Device
Type
NetvoxPayLoadData
SetAlarm
OnTimeReq
0x09
0xD2
AlarmONTime
(2Bytes,Unit:1s)
Reserved
(7Bytes,Fixed 0x00)
SetAlarm
OnTimeRsp
0x89
Status
(0x00_success)
Reserved
(8Bytes,Fixed 0x00)
GetAlarm
OnTimeReq
0x0A
Reserved
(9Bytes,Fixed 0x00)
GetAlarm
OnTimeRsp
0x8A
AlarmONTime
(2Bytes,Unit:1s)
Reserved
(7Bytes,Fixed 0x00)
Set buzzer alarm time = 5s
Downlink: 09D2000500000000000000
Response:
89D2000000000000000000（Configuration success）
89D2010000000000000000（Configuration failure）
7.2.6 Dry Contact Point Out Type
FPort：0x07
Description
Cmd
ID
Device
Type
NetvoxPayLoadData
Set DryContact
PointOutTypeReq
0x0B
0xD2
DryContactPointOutType (1Byte)
0x00_Normally Open
0x01_Normally Close
Reserved
(8Bytes,Fixed 0x00)
Set DryContact
PointOutTypeRsp
0x8B
Status
(0x00_success)
Reserved
(8Bytes,Fixed 0x00)
Get DryContact
PointOutTypeReq
0x0C
Reserved
(9Bytes,Fixed 0x00)
Get DryContact
PointOutTypeRsp
0x8C
DryContactPointOutType (1Byte)
0x00_Normally Open
0x01_Normally Close
Reserved
(8Bytes,Fixed 0x00)