Network Technologies Incorporated VOPEX-C64K10GB-4HDBT User manual

4-Port 4K HDMI HDBase-T Splitter/Extender
VOPEX-C64K10GB-4HDBT
ST-C64K10GB-R-HDBT
Receiver (Sold separately)
MAN301 REV 1/11/18
Instruction Manual

Features
• Incorporates HDBaseT technology
•Distribute 1Ultra HD HDMI signal to 4 identical HDBaseT outputs, with 1x loop HDMI output
•HDCP 2.2/1.4 compliant
•Transmitter Distance up to 100m under 1080p, 70m under 4K
•Support resolution to 4K@60Hz, YUV 4:2:0, VESA resolution up to 1920x1200
•Support Dolby TrueHD, DTS-HD Master Audio
•With wide-band Bi-Directional IR control (38 ~ 56 kHz)
(IR extension from Sender to Receiver or from Receiver to Sender)
•HDBaseT output 1 supports RS232 and Ethernet pass through
•Support 3D
•Support POC (Receiver powered by HDBaseT Splitter)
•DC 12V power supply

-5 to +35 C(+23 to +95 F)
5 to 90%RH (No Condensation)
10.2Gbps
Resolutions up to 4K@60Hz, YUV 4:2:0
VESA
resolution
1x HDMI input
1x HDMI loop output
4x RJ45 output
2x Power DC receptacle
1x Phoenix RS232 port
2x Ethernet port
100m(1080P), 70m(4K)
110-240V/ 12V DC power supply
15Watts
L305xW165.2xH39.8mm
1425g
Packing contents
1) Main Unit: 1x4 HDBaseT Splitter
2) 2x Power supply DC 12V
3) 4x IR-TX cable
4) 4x IR-RX cable
5) 1x Phoenix plugs for RS232 cable termination
6) 4x screws
7) 2x detachable mounting ears
8) Operating Instruction manual
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Panel Descriptions
Connecting and Operating
Applications

VESA Resolution
Refresh rate VESA Resolution
59.94Hz 640x480
640x480
800x600
1024x768
1280x768
1280x960
1280x1024
1680x1050
1920x1080
1280x720
1360x768
1400x1050
1920x1200
60Hz
Dimensional drawing

Please restart the splitter after changing EDID mode!
Front Panel
Rear Panel
Power ON/OFF
1Indicator of Loop out 2
Indicator of out
3
Reset button
5Indicator of Power 6
DIP switch for EDID setting
4
RS232 port
7
Ethernet port
1
2 3 453367
3
5HDMI Output port
7Main power
Note:
Connecting and operating
1) Connect the HDMI input source into HDBaseT splitter.
2) Connect HDBaseT splitter and ST-C64K10GB-R-HDBT Receivers (up to 4)
over Cat6 cable. The Cat6 cable must follow EIA-TIA 568b standards.
3) Connect the HDMI output of each Receiver to an HDMI Display.
Output2,3&4 port
POC port
HDMI Input port
2
4
6
Output1 port (Ethernet, RS232 pass-though)
EDID
0 0
0 1
1 0
1 1
4K@60Hz、YCBCR420、3D、DOLBY5.1
1080P@60Hz、2CH
1080P@24Hz、3D、DOLBY5.1
4K@30Hz、2CH

7) Alternatively, to use the Ethernet-based features, connect as follows:
1.Connect Ethernet cable into ethernet port on HDBaseT splitter.
2.Connect Ethernet cable between Output 1 and an Ethernet extender receiver and Smart TV.
Note:1.The Ethernet function is designed for Ethernet-compatible receiver units only.
2.Only Output1 supports Ethernet function.
8) Copy EDID function
Copy the EDID of the sink which connected the loop HDMI.
4) Connect 4pcs IR TX cables to the IR-TX sockets on the splitter and connect 4pcs IR RX cables
to the IR-RX sockets on the splitter.
5) Connect IR RX cable to IR-In port of Receiver, connect IR TX cable in to IR-Out port of Receiver.
6) Power up all units, the splitter,Receiver, sources and displays.

Application drawing showing connections using the Ethernet support option: