Crestron HD-TX-USB-2000-C User manual

DO GUIDE
HD-EXT-USB-2000-C
4K HDMI®and USB over HDBaseT®Extender 2000
DO Connect the Devices
Make connections to the transmitter and receiver as required.
Connecting the Transmitter
Make connections to the front and rear panels of the transmitter.
Front Panel Connections
Rear Panel Connections
DO Install the Devices
The Crestron®HD-EXT-USB-2000-C consists of the HD-TX-USB-2000-C transmitter and the
HD-RX-USB-2000-C receiver. The transmitter and receiver can be mounted on a at surface or onto
a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the transmitter and receiver onto a at surface
such as a wall.
Mounting onto a Wall
Mounting onto a Rack Rail
The transmitter and receiver can be mounted onto the front or rear rail of a rack. Position either the
left or the right mounting ange of the device so that the holes align with the holes in the rack. Then,
secure the device to the rack using two mounting screws (not included).
Mounting onto a Rack Rail
DO Check the Box
QTY PRODUCT PART NUM.
HD-TX-USB-2000-C
2Connector, 2-Pin 2049091
1Connector, 3-Pin 2049092
1Connector, 5-Pin 2049093
HD-RX-USB-2000-C
2Connector, 2-Pin 2049091
1Connector, 3-Pin 2049092
1Connector, 5-Pin 2049093
1 Power Pack, 24 Vdc, 1.25 A, 100-240 Vac 2045870
HDMI IN:
From HDMI®
audio/video
source
AUDIO IN:
From balanced/
unbalanced
analog audio
source
1
AUDIO IN:
From balanced/
unbalanced
analog audio
source
1
(Host):
To USB
device
(Device):
To USB
host
HDBT OUT:
To HDBT IN port
on receiver
IR IN:
From
Crestron®IR
control port
or other IR
signal source3
IR IN:
From
Crestron IR
control port
or other IR
signal source3
IR OUT:
To IR
emitter4
IR OUT:
To IR
emitter4
COM:
To
RS-232
device2
COM:
To
RS-232
device2
:
Passive pass-through
to Ethernet port on
receiver

DO GUIDE DOC. 7999C (2049074) 01.18
Specications subject to change without notice.
Connecting the Receiver
Make connections to the front and rear panels of the receiver.
Front Panel Connections
Rear Panel Connections
NOTE: Connection of the included power pack to the receiver powers both the receiver and the
transmitter. Power is transmitted over the cable that connects the HDBT IN port of the receiver to the
HDBT OUT port of the transmitter.
DO Select the USB Mode
The front panel of the receiver provides a three-position USB switch. Set the switch to one of the
following positions:
• AUTO: (Default setting) Sets the USB mode to HOST or DEVICE based on the last device
connected to either of the two USB ports on the receiver. If the last connected device is
disconnected, the USB mode returns to the mode of the previously connected device.
• HOST: Sets the USB mode to HOST, which allows data to pass between the USB Type
A host port on the receiver and the USB Type micro-B device port on the transmitter.
Connection to the USB Type micro-B device port on the receiver is ignored.
• DEVICE: Sets the USB mode to DEVICE, which allows data to pass between the USB
Type micro-B device port on the receiver and the USB Type A host port on the transmitter.
Connection to the USB Type A host port on the receiver is ignored.
NOTE: The USB mode of the transmitter is congured automatically to operate with the USB mode
of the receiver.
DO Select the Audio Mode
The front panel of the transmitter provides a two-position audio selection switch. Set the switch to
one of the following positions:
• HDMI: (Default setting) Uses audio embedded in the HDMI stream.
• ANALOG: Inserts analog audio into the video stream.
1. Only one AUDIO IN port on the device can be used at one time—both ports cannot be used simultaneously.
2. Only one COM port on the device can be used at one time—both ports cannot be used simultaneously.
3. Only one IR IN port on the device can be used at one time—both ports cannot be used simultaneously. IR IN supports
up to 60 kHz.
4. Only one IR OUT port on the device can be used at one time—both ports cannot be used simultaneously. IR OUT
supports up to 60 kHz.
5. Only one AUDIO OUT port on the device can be used at one time—both ports cannot be used simultaneously.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL®Standards and requirements tested by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
This unit is for indoor use only. It is not intended for outdoor use.
Cet appareil est réservé à une utilisation en intérieur. Il n’est pas destiné à une utilisation en extérieur.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B).
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT is either a trademark or
registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or
other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
HDMI OUT:
To HDMI
display
AUDIO OUT:
To analog audio
output device5
AUDIO OUT:
To analog audio
output device5
(Host):
To USB
device
(Device):
To USB
host
24 V
1.25 A:
From included
power pack
:
Passive pass-through
to Ethernet port on
transmitter
HDBT IN:
From HDBT OUT
port on transmitter
COM:
To
RS-232
device2
COM:
To
RS-232
device2
IR OUT:
To IR
emitter4
IR OUT:
To IR
emitter4
IR IN:
From
Crestron IR
control port
or other IR
signal source3
IR IN:
From
Crestron IR
control port
or other IR
signal source3