GLIDEAWAY EDISON User manual

INCLUDED
QUICK START GUIDE: EDISON
ASSEMBLY INSTRUCTIONS
B C
E
Dx4
+
–
+
–
L
F G
J
A
1
A
2
H
I
K
for use with TXL,
SCK, SQ models only
x8
OR
OR
x8
1
3
Insert the foot
motor cable (has
red band) into the
slot labeled foot
motor on the
control box.
INSTRUCTIONS (continued on back)
12IMPORTANT:
Tighten legs securely.
NOTE:
King-size bases
require a minimum of
two leg segments on
each leg of the base.
Failure to use at least
two leg segments
could result in damage
to floor and base and
will void product
warranty.
A
1A
2
H
I
J
E
E
4
B
BB
LL
K
5
TO OUTLET
B
G
6
NOTE:
A minimum of
2 people is
required when
turning over
base.
D
D
A
1
FROM BASE
Connect PART B to PART G.
Then connect PART B to
cable (pre-attached to bed
base).
DO NOT rest bed on its side as damage to USB ports will occur. DO NOT lean bed against bed legs.
WARNING:
See back of sheet for
instructions on pairing 2
bases to act as one.
(TXL, SCK, SQ models only)

ASSEMBLY INSTRUCTIONS (cont’d)
QUICK START GUIDE: EDISON
SAFETY INFORMATION
2
ATTENTION!
IMPORTANT SAFETY INSTRUCTIONS. SAVE THIS MANUAL! PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS PRODUCT. PROPER OPERATION OF YOUR ADJUSTABLE
BED IS NECESSARY TO ENSURE THE LONG LIFE AND DURABILITY YOU EXPECT FROM A HIGH QUALITY PRODUCT. THE MANUFACTURER HAS TESTED AND INSPECTED THIS PRODUCT PRIOR
TO SHIPMENT.
RADIO FREQUENCY IS 2.4 GHZ
FCC compliance device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void the user’s right to operate the device. The input voltage is AC100-240 50/60HZ; the output voltage is DC29V 1.8A.
ELECTRICAL SAFETY
Always unplug this adjustable bed frame from the electrical outlet before any cleaning or maintenance of the bed frame. To safely disconnect, remove the plug from the outlet. Keep cord away from
heated surfaces. Use only indoors. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO MOISTURE. Discontinue use of this adjustable bed base and contact the
manufacturer for repair if: (1) it has a damaged cord or plug, (2) it is not working properly, (3) it has been dropped or damaged. FOR OPTIMAL SAFETY, YOUR ADJUSTABLE BED SHOULD BE
PLUGGED INTO A SURGE PROTECTOR (not supplied with this adjustable bed).
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Warning – Danger of explosion if battery is incorrectly replaced. Replace only with the 6LR61 9V batteries and LR03 AAA batteries.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A reversed battery may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
5. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s directions.)
WARRANTY WARNING
This bed is specifically designed to require no maintenance by you, the user. Any opening or tampering with the control box, motors or hand controls (with the exception of the battery compartment,
if equipped) will void the warranty. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Only those authorized may
conduct repairs or part replacement on your adjustable bed.
IN-HOME USE ONLY
This adjustable bed is designed exclusively for in-home use.
HOSPITAL/MEDICAL DISCLAIMER
This base is NOT designed for commercial hospital or medical use and is NOT designed to meet hospital standards. Do not use this base with TENT TYPE oxygen therapy equipment or use near
explosive gases.
CONSUMERS WITH PACEMAKERS
It is possible that the vibrating feature of this bed may be interpreted falsely by some pacemakers as movement and/or exercise. This is common with any product that produces a vibrating motion,
and may or may not affect your pacemaker. Please consult your physician with any concerns.
PRODUCT RATINGS
Lift Motor Restrictions: The lift motors in this bed are NOT designed to operate continuously for more than one (1) minute over an eight (8) minute time period, or approximately 12% duty cycle. To
ensure reliable functionality and full life of this product, do not attempt to exceed these limits. NOTE: Attempting to circumvent or exceed this rating will shorten the life expectancy of the product
and may void the warranty.
Weight Restrictions: The recommended weight limits on our adjustable beds are: Queen: 600 lb Full/XL: 500 lb Twin/XL: 400 lb (800 lb if using two twins as a King) 1/pc King: 800 lbs
The structure of the bed will support the recommended weight when distributed evenly across the bed. The head and foot sections are not designed to individually support or lift this amount of
weight. For optimal performance and integrity of structure, enter and exit ONLY when head and foot sections are flat. NOTE: Exceeding the recommended weight restrictions could damage your
adjustable bed and void your warranty.
SMALL CHILDREN AND PETS WARNING
Immediately dispose of all packing materials as they can pose a smothering risk to small children and pets. Injury could occur also if children or pets are permitted to play on or under the bed. Do not
allow children to operate this bed without adult supervision.
LUBRICATION AND CLEANING
This product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any
nylon nuts or the base may inadvertently creep downward from the elevated position.
LIFT WARNING
DO NOT SIT ON THE HEAD OR FOOT SECTIONS WHILE IN THE RAISED POSITION, OR DURING LIFT OR LOWERING CYCLES.
LOCATION ENVIRONMENT
The level of sound experienced during operation is directly related to the location environment. For example, when a base is located on a hardwood floor with the vibe feature in operation, a vibrating
tone will be audible. To minimize this resonance, place a piece of carpet under each leg of the base. It is possible to experience vibration or noise from the headboard brackets, headboards or foot
boards if mounting bolts are not firmly tightened.
MOVING AFTER INSTALLATION
Do not place adjustable bed base vertically on its head, foot sections or sides. This may cause injury to persons or damage to base.
WARNINGS
To reduce the risk of burns, fire, electric shock, or injury to persons:
• Unplug from outlet before putting on or taking off accessories.
• Close supervision is necessary when this base is used by, or near children, invalids, disabled persons, or pets.
• Use this base only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
• Never operate this base if it has a damaged cord or plug, is not working properly, has been dropped or damaged, or dropped in water.
• Keep the cord away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
• To disconnect, remove plug from outlet.
• DO NOT USE NEAR PEOPLE USING OR WEARING MEDICAL DEVICES. FOR HOUSEHOLD/RESIDENTIAL USE ONLY.
RESOURCES
CUSTOMER SERVICE
1-855-581-3095
VISIT US ONLINE
glideaway.com
Simultaneously
press & hold the
HEAD UP and
HEAD DOWN
button on remote
until the remote
back lights blink,
then release
remote buttons.
If pairing 2 bases (TXL, SCK, SQ)
together, follow these instructions.
Connect each base to the other by
inserting PART F into each control
box (insert into slot labeled sync on
each control box).
8
7
+
–
+
–
C
L
G
C
C
C
F
Double click the PAIR button on the
control box (light on control box will turn
blue) to initiate pairing mode.
PAIR
SYNC
INSTRUCTIONS TO SYNC REMOTE TO BASE
INSTRUCTIONS TO PAIR 2 BASES TO ACT AS ONE
REV 07.31.19