New Classic Home Furnishings 45-150-21C User manual

New Classic Home Furnishings
Tel [phone] •FAX [phone] •WEB www.newclassicfurniture.com
COUNTER CHAIR-CUSHION SEAT- ASSEMBLY INSTRUCTIONS
REFER TO DIAGRAM BEFORE COMPLETING EACH STEP
ITEM：45-150-21C
PARTS AND HARDWARE LIST
Use only the screws provided
to assemble chair. Using
different or longer screws could
result in splits or damage to the
chair.
DO NOT USE POWER TOOLS FOR
ASSEMBLY
1. ASSEMBLE SEAT FRAME AND BACK: Match up the holes
on the Seat Frame (C) to the Back Leg Assembly (A).
2. Thread a Flat Washer (L) onto a Long Bolt (H). Then slide a
Lock Washer (M) on the same bolt and insert the bolt
assemblyinto thepredrilled cornerholesof theSeat Frame
and the matching holeson theBackLegAssembly. Tighten
them with the Allen Wrench (K) provided. Repeat with other
back corner.
3. Thread a Flat Washer (L) onto a Short Bolt (J). Then slide a
Lock Washer (M) on the same bolt and insert this assembly
into the predrilled holes on the back of the Seat Frame and
the matching holeson the Back Leg Assembly. Tighten
them with the Allen Wrench (K) provided.Repeat with remain
holes onback of seat frame.
4. Insert Link Bars (E1,E2) into the holes provided on the lower
portion of the Back Leg Assembly (A). There isa predrilled
hole on each end ofthe link bars. Make sure those holes are
positioned facing down (Towardsthe floorwhen the chair is
completelyassembled)
5. ASSEMBLE FRONT: Insert the Front Stretcher (F) into the
Front Legs (D1 and D2) using theholes on the lowerportion
of each leg.There is a predrilled hole oneach end ofthe
stretcher. Make sure the hole is facing towards the floor after
the stretcher is inserted.
6. CONNECT FRONT AND BACK: Insert the Front Leg
Assembly from Step 4 into the appropriateslots of the Seat
Frame (C).
7. Fit the LinkBars (E1, E2)from step 3 into the appropriate
holes of the front legs.
8. Match the holes atthe top corner ofeach legwith the holes at
the front corners of the Seat Frame. Thread a Flat Washer (L)
and Lock Washer (M) onto a Medium Bolt (I). Insert this bolt
assemblythrough theSeatFrameand into the matchingholes
on the FrontLegs. Do not fully tighten. Repeat with the other
legs, securing loosely.
9. Before completely tightening Seat Frame to Legs, check to
make sure the holes on the Front Stretcherand LinkBars are
still facing down (Towards the Floor when the chair is
completelyassembled). Tighten all bolts.
10. SECURE STRETCHERS and LINK BARS: Insert a Long Screw (G) through the predrilledhole on each stretcher and link barand tighten with a screwdriver.
11. ATTACH SEAT: PlaceSeat (B) on the Seat Frame and secure from underside using shortscrewsprovided.
9PCS
LockWasher
QTY
4PCS
4PCS
1PC
1PC
9PCS
DESCRIPTION
Flat Washer
Allen Wrench
NO
H
K
I
D2
D1FrontLeg(Left)
FrontLeg(Right)
1PC
1PC
DESCRIPTION
Seat Frame
C
A
NO
Back Leg Assembly
1PC
1PC
QTY
L
E2
E1Link Bar(Left)
Link Bar(Right)
1PC
1PC
FFront Stretcher 1PC M
J
9PCS
GLong Screw
Long Bolt 3 1/4inches
Medium Bolt 2 1/4inches
Short Bolt 1 2/4inches

New Classic Home Furnishings
Tel [phone] •FAX [phone] •WEB www.newclassicfurniture.com
COUNTER CHAIR –WOOD SEAT- ASSEMBLY INSTRUCTIONS
REFER TO DIAGRAM BEFORE COMPLETING EACH STEP
ITEM：45-150-21 T
PARTS AND HARDWARE LIST
Use only the screws provided
to assemble chair. Using
different or longer screws could
result in splits or damage to the
chair.
DO NOT USE POWER TOOLS FOR
ASSEMBLY
1. ASSEMBLE SEAT FRAME AND BACK: Match up the holes
on the Seat Frame (C) to the Back Leg Assembly (A).
2. Thread a Flat Washer (L) onto a Long Bolt (H). Then slide a
Lock Washer (M) on the same bolt and insert the bolt
assemblyinto thepredrilled cornerholesof theSeat Frame
and the matching holeson theBackLegAssembly. Tighten
them with the Allen Wrench (K) provided. Repeat with other
back corner.
3. Thread a Flat Washer (L) onto a Short Bolt (J). Then slide a
Lock Washer (M) on the same bolt and insert this assembly
into the predrilled holes on the back of the Seat Frame and
the matching holeson the Back Leg Assembly. Tighten
them with the Allen Wrench (K) provided.Repeat with remain
holes onback of seat frame.
4. Insert Link Bars (E1,E2) into the holes provided on the lower
portion of the Back Leg Assembly (A). There isa predrilled
hole on each end ofthe link bars. Make sure those holes are
positioned facing down (Towardsthe floorwhen the chair is
completelyassembled)
5. ASSEMBLE FRONT: Insert the Front Stretcher (F) into the
Front Legs (D1 and D2) using theholes on the lowerportion
of each leg.There is a predrilled hole oneach end ofthe
stretcher. Make sure the hole is facing towards the floor after
the stretcher is inserted.
6. CONNECT FRONT AND BACK: Insert the Front Leg
Assembly from Step 4 into the appropriateslots of the Seat
Frame (C).
7. Fit the LinkBars (E1, E2) from step 3 into the appropriate
holes of the front legs.
8. Match the holes atthe top corner ofeach legwith the holes at
the front corners of the Seat Frame. Thread a Flat Washer (L)
and Lock Washer (M) onto a Medium Bolt (I). Insert this bolt
assemblythrough theSeatFrameand into the matchingholes
on the FrontLegs. Do not fully tighten. Repeat with the other
legs, securing loosely.
9. Before completely tightening Seat Frame to Legs, check to
make sure the holes on the Front Stretcherand LinkBars are
still facing down (Towards the Floor when the chair is
completelyassembled). Tighten all bolts.
10. SECURE STRETCHERS and LINK BARS: Insert a Long Screw (G) through the predrilledhole on each stretcher and link barand tightenwith a screwdriver.
11. ATTACH SEAT: PlaceSeat (B) on the Seat Frame and secure from underside using shortscrewsprovided.
9PCS
LockWasher
QTY
4PCS
4PCS
1PC
1PC
9PCS
DESCRIPTION
Flat Washer
Allen Wrench
NO
H
K
I
D2
D1FrontLeg(Left)
FrontLeg(Right)
1PC
1PC
DESCRIPTION
Seat Frame
C
A
NO
Back Leg Assembly
1PC
1PC
QTY
L
E2
E1Link Bar(Left)
Link Bar(Right)
1PC
1PC
FFront Stretcher 1PC M
J
9PCS
GLong Screw
Long Bolt 3 1/4inches
Medium Bolt 2 1/4inches
Short Bolt 1 2/4inches