New Classic Home Furnishings GIA D1701-42S User manual

Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the PARTS LIST and/or HARDWARE LIST shown below.
Caution: Please read the instructions thoroughly before assembly.
1. We recommend that you assemble this product with the assistance of another person; this will make the
assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
2. Please do not over tighten screws or bolts until the assembly is completed.
3. Please put all parts on a non-abrasive floor before assembly,and follow the assembly steps to assemble
your newly purchased product correctly and efficently.
Assembly Instructions
MADE IN VIETNAM PAGE: 1 OF 3
ITEM NO. D1701-42S
GIA 42” COUNTER DROP LEAF TABLE W/2 CHAIRS
PARTS LIST HARDWARE LIST
NO.
A
COMPONENT
CHAIR BACK
SKETCH QTY.
2 PCS
B SEAT FRAME 2 PCS
DFRONT LEG
(RIGHT) 2 PCS
E
SIDE
STRETCHER
(LEFT)
2 PCS
DFRONT LEG
(LEFT) 2 PCS
FFRONT
STRETCHER 2 PCS
E
SIDE
STRETCHER
(RIGHT)
2 PCS
C CUSHION SEAT 2 PCS
NO.
1
COMPONENT
FLAT WASHER
5/16” DIA.
SPRING
WASHER
5/16” DIA.
SKETCH QTY.
22 PCS
222 PCS
NUT
5/16” DIA.
ALLEN
WRENCH
5/16” DIA.
38 PCS
41 PC
LONG BOLT
1/4” x 3”
68 PCS
WOOD SCREW
5/32” x 1 1/2”
724 PCS
SHORT BOLT
1/4” x 1 3/4”
56 PCS

MADE IN VIETNAM PAGE: 2 OF 3
Assembly Instructions
1
2
5
4
6
4
21
BB
A
A
E (Right)
7
7
E (Left)
7
7
3
2
14
A
B
D (Left)
E (Right)
D (Right)
E (Left)
7
7
F
7
7
7
7
77
STEP 3
Install front stretcher into the holes of the front legs
then attached to the seat frame.
STEP 4
Place the assembled seat frame on the cushion seat
and attach with wood screws.
To assemble the chairs, please follow the following steps and repeat for each chair:
STEP 1
Lay the chair back on soft clean surface and install
the seat frame.
STEP 2
Insert side stretchers with wood screws.
ITEM NO. D1701-42S
GIA 42” COUNTER DROP LEAF TABLE W/2 CHAIRS

Assembly Instructions
MADE IN VIETNAM PAGE: 3 OF 3
ITEM NO. D1701-42S
GIA 42” COUNTER DROP LEAF TABLE W/2 CHAIRS
PARTS LIST HARDWARE LIST
NO.
1
COMPONENT
FLAT WASHER
5/16” DIA.
SKETCH QTY.
8 PCS
2SPRING WASHER
5/16” DIA. 8 PCS
3BOLT
5/16” x 65 MM 8 PCS
4ALLEN KEY
4 MM 1 PC
NO.
A
COMPONENT
TABLE TOP
SKETCH QTY.
1 PC
BTABLE SHELF 1 PC
CTABLE LEG 4 PCS
A
4321
C
B
To assemble the table, please follow the following
steps but do not tighten all bolts:
STEP 1: Install 3 of the table legs first.
STEP 2: Install the table shelf.
STEP 3: Install the last table leg.
STEP 4: Turn the table to the upright position
carefully and make sure the table is level,
then tighten all bolts.