New Holland 918H User manual

New Holland
Flail Mower Specifications
918H 918L
Page 1 of 1
MODEL 918H 918H 918H
SIZE 60-inch 71-inch 91-inch
PTO hp rating............................................................................................................................................................70...............................................................................................
Rate spee (rpm)...................................................................................................................................................540..............................................................................................
Nominal cutting wi th, in. (mm) 60 (1524.0) 71 (1803.4) 88 (2235.2)
Offset a justment to right, in. (mm) 28 (711.2) 28 (711.2) 24 (609.6)
Offset a justment to left, in. (mm) n/a 46
Cutting height range, in. (mm) 0.5 to 5 (13 to 127) 0.5 to 5 (13 to 127) 0.8 to 5 (19 to 127)
Cutting height a justment increments, in. (mm).................................................................................................1 (25.4) ..........................................................................................
Rotor iameter, tip-to-tip, in. (mm) 15.8 (401.32) 15.8 (401.32) 16.50 (419.1)
Rotor rotation.................................................................................................................................................forwar /reverse ....................................................................................
Guage roller iameter, in. (mm) ........................................................................................................................5.2 (132.1)........................................................................................
Bla e mounting .................................................................................................................................................single hinge.......................................................................................
Bla e type ............................................................................................................................................................stan ar ..........................................................................................
Number of bla es 80 96 128
Bla e tip spee (fpm) 9237 9237 9659
Rotor shaft spee (rpm).........................................................................................................................................2236.............................................................................................
Thickness of flail eck, in. (mm) ........................................................................................................................0.16 (4.0).........................................................................................
Thickness of flail en s, in. (mm) ........................................................................................................................0.24 (6.0).........................................................................................
Lift linkage.............................................................................................................................................................flexible ...........................................................................................
Three-point hitch category .....................................................................................................................................I or II ............................................................................................
Weight, lbs. (kg) 697 (316.2) 792 (359.3) 957 (434.1)
MODEL 918L 918L
SIZE 50-inch 60-inch
PTO hp rating ...........................................................................................................................30 ...............................................................................................................................
Rate spee (rpm) ..................................................................................................................540 ..............................................................................................................................
Nominal cutting wi th, in. (mm) 50 (1270) 60 (1524)
Offset a justment to right, in. (mm) 10 (254) 20 (508)
Offset a justment to left, in. (mm) ..........................................................................................n/a...............................................................................................................................
Cutting height range, in. (mm)...................................................................................0.75 to 3 (19 to 76) .................................................................................................................
Cutting height a justment increments, in. (mm)..............................................................0.75 (19.1) ........................................................................................................................
Rotor iameter, tip-to-tip, in. (mm) .................................................................................13.5 (342.9) .......................................................................................................................
Rotor rotation .......................................................................................................................reverse ...........................................................................................................................
Guage roller iameter, in. (mm).........................................................................................3.5 (88.9) .........................................................................................................................
Bla e mounting.................................................................................................................single hinge .......................................................................................................................
Bla e type................................................................................................................................fine ..............................................................................................................................
Number of bla es 80 96
Bla e tip spee (fpm) ............................................................................................................7,522.............................................................................................................................
Rotor shaft spee (rpm) ........................................................................................................2,137.............................................................................................................................
Thickness of flail eck, in. (mm).........................................................................................0.1 (2.5) ..........................................................................................................................
Thickness of flail en s, in. (mm).........................................................................................0.2 (5.0) ..........................................................................................................................
Lift linkage ..............................................................................................................................fixe .............................................................................................................................
Three-point hitch category ........................................................................................................ I................................................................................................................................
Weight, lbs. (kg) 348 (157.9) 383 (173.7)
Safety begins with a th r ugh understanding f
the equipment. Always make sure y u and
y ur perat rs read the Operat r’s Manual
bef re using the equipment. Pay cl se
attenti n t all safety and perating
decals and never perate machinery
with ut all shields, pr tective devices
and structures in place.
Design, materials and/ r specificati ns are subject t
change with ut n tice and with ut liability theref r.
Specificati ns are applicable t units s ld in Canada, the
United States, its territ ries and p ssessi ns, and may
var y utside these areas.
© 2008 CNH America LLC
New H lland is a registered trademark f CNH America LLC.
Visit ur Web site at www.newholland.com/na. Or, call t ll-free 866-NEW-HLND (866-639-4563).