Newall DP700 MK2 User manual

DP700 MK2 Quick Start Guide
Technical Specification
For the complete manual please download from:
http://n wall.com , Click Technical Support to access the download page.
Environm ntal
Op rating T mp ratur Storag T mp ratur
-10°C to 50°C -20 to 70°C
Environm ntal Conditions - IP40 (Stand Alone)
IP54 (Panel Mount)
R lativ Humidity - maximum 95% for temperature up to 31°C
Disposal
At the end of it’s life, you should dispose of the DP700 in a safe
manner applicable to electronic goods.
The case work is suitable for recycling. Please consult local
regulations on disposal.
DP7001016ENUS
023-81365-U /0
Connections
El ctrical
EU Directive 73/23/EEC (Low Voltage
Directive)
BS EN 55022:1998 Class B
BS EN 55024:1998
Input to Pow r Supply Unit (Suppli d)
100-240V (47-63Hz)
Ext rnal switch-mod
Output voltage 15VDC
Input Voltag to DP700
15-24VDC ±10%
Conforms to Low Voltage Directive
External PSU Input
AMERICAS
Newall Electronics Inc.
USA
Tel: [phone]
CHINA & TAIWAN
Sensata Technologies China Co., Ltd.
People's Republic of China
Tel: [phone]
SINGAPORE AND KOREA
Sensata Technologies Co., Ltd.
Singapore
Tel: [phone]
JAPAN
Sensata Technologies Japan Ltd.
Japan
Tel: [phone]
For more information about this or any of our products
please contact us at [email protected] or visit www.newall.com
Note: Newall Measurements Systems reserves the right to change specifications without notice.
Warnings
The mains supply is connected into a switch mode power supply (separate from your DP700) via a
detachable supply cord supplied. If another supply cord is used, it must have fitted a C5, 10A, EARTHED
mains connector with a cord rated for at least 10A.
If a mains plug is not already fitted to the supply cord or is of the wrong type, then a suitable EARTHED plug
should be used which complies with the relevant specifications for plugs and socket-outlets.
You can only use the DP700 with Newall Spherosyn and Microsyn analogue encoders.
Unit only to be serviced by Newall qualified personnel or authorised alternatives.
Turn off the power by disconnecting the power supply connector before you connect the encoder(s)
Cabinet equipotential terminal
for grounding to machine
Cable Clamp
Encoder Input
Connection
1,2 or 3 According
to Model
RS232 Output

SETTING UP THE UNIT
setup
l n g u g e
Understanding the Keypad
D fault S ttings Optional S ttings
Eng gb Eng US fr.
Preset an Axis
=
Microsyn 10 Microsyn 5
Must be set to match encoders on the machine
*
*Lathe version, X axis set to DIA as default
Message
Display
Axis Selection ey
Numeric eys
Enter ey
Clear Numeric Entry
Center Find
Undo ey
Digifind / Reference
Switches between Zero
and Axis Preset modes
Switches between Absolute
and Incremental modes
Information selection (scrolls
through options on Message
display)
Function Menu ey
Function Navigation eys
Switches between Inch
and mm display
Zero an Axis in Zero Mode
Ensure DP700 is
in Zero Mode of Axis 1, 2 or 3
Zero an Axis in Set Mode
Ensure DP700 is
in Set Mode of Axis 1, 2 or 3
Ensure DP700 is
in Set Mode
Until display
shows
display
shows
Spherosyn 2G
of axis 1
of axis 1, 2 or 3
See full manual on website for more details
user defined, use numeric keypad to enter value
(value is in whole minutes)
See full manual on website for more details to exit setup
of axis 1
cesky
DANSK deutsch esp nol
f r n c i s i t l i n o n e d e r l n
pol
setup
TYPE GENERIC MILL LATHE
setup
ENCODER SPH 2G USN 10 USN 5
setup
RES 0.005 0.01 0.02 0.05
0.001 0.002
setup
DIR ---| |---
setup
MEASURE RAD DIA
setup
ZERO APP 0.000 Use numeric keypad to enter a value
setup
ERR COMP
setup
PLANE
(----)
(----)
(----)
(----)
(----)
(----)
setup
feed minutes seconds
setup
funcs ON OFF
setup
bEEP o n
setup
sleep
setup
COdE?
FUNCS
SETUP
-145.230
Not : values in mm
portugue russi n
turkce
of axis 1, 2 or 3
of axis 1, 2 or 3
of axis 1, 2 or 3
of axis 1, 2 or 3
Off
of axis 1
of axis 1
ENTERING SETUP
set func
t o o l s
of axis 1
to scroll through functions, to return to setup menu
OFF
of axis 1
0
setup
reset
Sleep key
Axis 1
Axis 2
Axis 3
Power
LED
0
T00l 01