Newall E70 Troubleshooting guide

E70 Quick Start up Guide
Technical Specification
N
For the complete manual please download from:
http://newall.com , Click technical Support to access the download
page.
Environmental
Operating Temperature Storage Temperature
0 to 45°C -20 to 60°C
Environmental Conditions - indoor use, IP20 (IEC 529)
Relative Humidity - maximum 80% for temperature up to 31°C
decreasing linearly to 33% at 45°C
Transient overvoltage according to INSTALLATION CATEGO-
RY II of IEC664
Pollution Degree 2 in accordance with IEC664
Disposal
At the end of it’s life, you should dispose of the E70 in a safe
manor applicable to electronic goods.
The case work is suitable for recycling. Please
consult local regulations on disposal.
A full hard copy of the manual is available free of charge on request
023-81340/0
DSU Connections
Electrical
EMC and Low Voltage Compliance
BS EN 61000-6-4:2001
BS EN 61000-6-2:2001
BS EN 61010-1:2001
Operating Voltage
100 - 240V
Supply Voltage Fluctuation
not to exceed 10% of operating voltage
Supply Frequency
50 to 60Hz
Maximum Power Consumption
18VA
IEC Inlet (Mains Supply)
Cabinet equipotential terminal
for grounding to machine Mains supply fuse
Input connectors 2 or 3
according to model
HEAD OFFICE
Newall Measurement Systems Ltd.
Technology Gateway, Cornwall Road
South Wigston
Leicester LE18 4XH
United Kingdom
Telephone: [phone]
Facsimile: [phone]
Email: [email protected]
Web: http://newall.com
Newall Electronics, Inc.
1778 Dividend Drive
Columbus, OH 43228
Telephone: [phone]
Toll Free: 800.229.4376
Facsimile: [phone]
Email: [email protected]
Web: http://newall.com
Note: Newall Measurements Systems reserves the right to change specifications without notice.
Warnings
On / off Switch
The mains supply is connected through a detachable supply cord supplied. If another supply cord is
used, it must have fitted a IEC320, 10A, EARTHED mains connector with a cord rated for at least 10A.
The PROTECTIVE EARTH CIRCUIT of the mains supply MUST BE CONNECTED to the protective earth
terminal of the cabinet through the supply cord.
If a mains plug is not already fitted to the supply cord or is of the wrong type, then a suitable EARTHED
plug should be used which complies with the relevant specifications for plugs and socket-outlets.
The mains supply fuse is a 20x5mm, type T0 .5A, 250v, Disconnect mains before replacing fuse.
The mains supply must be removed before opening the unit and completed by qualified personnel.
Auxillary connection (optional) Connection to the display
(Cable supplied)

Setting up the Unit
How to enter setup
,SETup
=
SETup
language
key beep
i/p type
resolutn
directn
err comp
Understanding the Keypad
X
0
3
6
9
2
5
8
1
4
7
.±
inch
mm
abs
inc
ent
1
ce
ref
*Refer to full user manual on website for more information on these functions
2
rad/dia
See full manual on website for details
Axis X
Axis Y
or Z
Axis Z
or Z1
Default Settings Optional Settings
*For the lathe variant E70-L will be shown
*
YZ
sdm
sdm
zero
del.
ins.
Rset
1+1
Zero axis (reset)
Axis selection key
Numeric keys
Switches between inch and
mm display*
Switches between absolute
and incremental modes*
Clear numeric entry
Centre find*
Enter key
Digifind / reference*
SDM
Insert and Delete
Arrows
Power
Mill Option Keys Lathe Option Keys
PCD function
Line hole function
ARC function
Polar coordiantes
Taper function
Tool use
Tool set
summing / vectoring
Lathe
version
abs
inc ,
sdm
pos out
zero app
normal
ARC
pcd
line
polar
tool
taper
quit
ent english
beep on
spherosn
rad
francais deutsch
Espanol
italiano dansk
Czech
beep off
usn 10 usn 5
dia
0.005 0.05 0.02
0.01 0.001
0.002
off
off
off
on
on
on
off
on
off on
quit nor default
To exit setup
ent
ent
ent
ent
ent 10
ent off
on
ent
See full manual on website details
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
ent
Preset an Axis
,or 21 .3ent =-12.300
±
XYZ
Microsyn 10 Microsyn 5
Mill
Lathe
Of X, Y or Z
Of X, Y or Z
Of X, Y or Z
Of X, Y or Z
Of X, Y or Z
Must be set to match encoder’s on the machine
*
*Lathe version, X axis set to DIA as default