Newport Electronics IDP INFINITY D User manual

IDP
INFINITY®D Process Meter
Operator’s Manual
®
NEWPORT Electronics,Inc.
http://www.newportUS.com/manuals
Downloaded from Elcodis.com electronic components distributor

Counters
Frequency Meters
PID Controllers
Clock/Timers
Printers
Process Meters
On/Off
Controllers
Recorders
Relative
umidity
Transmitters
Thermocouples
Thermistors
Wire
Rate Meters
Timers
Totalizers
Strain Gauge
Meters
Voltmeters
Multimeters
Soldering Iron
Testers
p pens
p Controllers
p Electrodes
RTDs
Thermowells
Flow Sensors
For Immediate Assistance
In the U.S.A. and Canada: 1-800-NEWPORT
®
In Mexico: (95) 800-NEWPORT
SM
Or call your local NEWPORT Office.
Internet e-mail
[email protected]
Additional products from
N WPORTnetSM On-Line Service
http://www.newportUS.com
®
NEWPORT Electronics,Inc.
It is the policy of NEWPORT to comply with all worldwide safety and EMC/EMI regulations that apply.
NEWPORT is constantly pursuing certification of its products to the European New Approach Directives.
NEWPORT will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct but NEWPORT Electronics, Inc. accepts no liability for
any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected applications.
PAT NT NOTIC : The “Meter Case Bezel Design” is a trademark of NEWPORT Electronics, Inc., registered in the U.S..
This product is covered by one or more of the following patents: U.S. Pat. No. Des. 336,895; 5,274,577 /
CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 /
UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2. OT ER INTERNATIONAL PATENTS PENDING.
This device is marked with the international caution symbol. It is important to read the Setup Guide before installing or
commissioning this device as it contains important information relating to safety and EMC.
Downloaded from Elcodis.com electronic components distributor

PREFACE
MANUAL OBJECTIVES
This manual shows you how to set up and use the Programmable Process meter.
NOTES, WARNINGS and CAUTIONS
Information that is especially important to note is identified by three labels:
• NOTE
• WARNING
• CAUTION
• IMPORTANT
NOTE: provides you with information that is important to successfully
setup and use of the Process meter.
CAUTION or WARNING: tells you about the risk of electric shock.
CAUTION, WARNING or IMPORTANT: tells you of circumstances
or practices that can effect the meter's functionality and must refer to
accompanying documents.
i
Downloaded from Elcodis.com electronic components distributor

Table of Contents
Section Page
SEC 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1. Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEC 2 ABOUT THE METER. . . . . . . . . . . . . . . . . . . . . . . . . . 3
.1 Front of the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. Back of the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
.3 Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SEC 3 GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Changing Configuration Jumpers. . . . . . . . . . . . . . . . . . . 7
3. Mounting the Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Connecting Sensor Input . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4 Connecting Main Power. . . . . . . . . . . . . . . . . . . . . . . . . 1
SEC 4 CONFIGURING THE METER . . . . . . . . . . . . . . . . . 13
4.1 Selecting the Input Range . . . . . . . . . . . . . . . . . . . . . . . 13
4. Selecting a Decimal Point Position. . . . . . . . . . . . . . . . . 14
4.3 Scaling the Meter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.1 Internal Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.3. Live Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.4 Changing the Meter’s Calibration. . . . . . . . . . . . . . . . . . 17
APPENDICES
A Checking and Changing Main Board Power Jumpers . . . 19
B Reference Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
C Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
D CE Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ii
Downloaded from Elcodis.com electronic components distributor

List of Figures
Figures Page
-1 Front-Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
- Connectors (ac-Powered and dc-Powered) . . . . . . . . . . . . . . .5
-3 dc-Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3-1 S1 - S4 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3- Meter - Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3-3 Panel Cut-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3-4 3-Wire dc Voltage Input Connections
with Internal Excitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3-5 -Wire dc Voltage Input Connections
with External Excitation . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3-6 4- 0 mA Input Connections with External Excitation . . . . . .10
3-7 4- 0 mA Transmitter Hook-Up with Internal Excitation . . . .11
3-8 dc Current Input Connections with Current Source . . . . . . .11
3-9 Main Power Connections ac . . . . . . . . . . . . . . . . . . . . . . . . 1
3-10 Main Power Connections dc . . . . . . . . . . . . . . . . . . . . . . . .1
A-1 115Vac Jumper Wiring (default) . . . . . . . . . . . . . . . . . . . . . .19
A- 30 Vac Jumper Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
C-1 Meter Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Tables
Table Page
-1 Connector Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3-1 S1 - S4 DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3- ac Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4-1 Meter Calibration Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
B-1 Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
B- Menu Configuration Displays . . . . . . . . . . . . . . . . . . . . . . . 1
B-3 Run Mode Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-4 Factory Preset Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
Downloaded from Elcodis.com electronic components distributor

NOTES
iv
Downloaded from Elcodis.com electronic components distributor

SECTION 1. INTRODUCTION
1.1 UNPACKING
Remove the Packing List and verify that you have received all equipment. If
there are any questions about the shipment, use the phone numbers listed on the
back cover to contact the Customer Service Department nearest you.
Upon receipt of shipment, inspect the container and equipment for any signs of
damage. Note any evidence of rough handling in transit. Immediately report any
damage to the shipping agent.
The carrier will not honor any claims unless all shipping material is
saved for their examination. After examining and removing contents,
save packing material and carton in the event reshipment is necessary.
Verify that you receive the following items in the shipping box:
QTY DESCRIPTION
1 Programmable indicator/controller with all applicable connectors
attached.
1 Owner’s Manual
1 Quick Start Manual
If you ordered any of the available options (except the “ L” blank Lens
option), they will be shipped in a separate container to avoid any
damage to your indicator/controler.
1
Downloaded from Elcodis.com electronic components distributor

1.2 SAFETY CONSIDERATIONS
This device is marked with the international caution symbol. It is important to
read this manual before installing or commissioning this device as it contains
important information relating to Safety and MC (Electromagnetic Compatibility).
This instrument is a panel mount device protected in accordance with EN 61010-
1:2001, electrical safety requirements for electrical equipment for measurement, con-
trol and laboratory. Installation of this instrument should be done by qualified person-
nel. In order to ensure safe operation, the following instructions should be followed.
This instrument has no power-on switch. An external switch or circuit-breaker shall
be included in the building installation as a disconnecting device. It shall be marked to
indicate this function, and it shall be in close proximity to the equipment within easy
reach of the operator. The switch or circuit-breaker shall not interrupt the Protective
Conductor (Earth wire), and it shall meet the relevant requirements of IEC 947–1 and
IEC 947-3 (International Electrotechnical Commission). The switch shall not be incor-
porated in the main supply cord.
Furthermore, to provide protection against excessive energy being drawn from the
main supply in case of a fault in the equipment, an overcurrent protection device shall
be installed.
• Do not exceed voltage rating on the label located on the top of the instrument
housing.
• Always disconnect power before changing signal and power connections.
• Do not use this instrument on a work bench without its case for safety reasons.
• Do not operate this instrument in flammable or explosive atmospheres.
• Do not expose this instrument to rain or moisture.
• Unit mounting should allow for adequate ventilation to ensure instrument does not
exceed operating temperature rating.
• Use electrical wires with adequate size to handle mechanical strain and power
requirements. Install without exposing bare wire outside the connector to minimize
electrical shock hazards.
MC Considerations
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wires close to the instrument if EMC problems
persist.
Failure to follow all instructions and warnings may result in injury!
Note ☞
Downloaded from Elcodis.com electronic components distributor

SECTION 2. ABOUT THE METER
2.1 FRONT OF THE METER
Figure -1 shows each part of the front of the meter.
Figure 2-1. Front Panel
METER DISPLAY:
Digital LED display: ¡.9.9.9. or 9.9.9.9. 4-digit 7–segment, 0.56" high LED
display with programmable decimal point.
METER MODES:
Run Mode The meter is in the run mode when the display is actively
showing a process.
Configuration Mode The meter is in the configuration mode when you press the
MENU button to enable meter configurations.
3
Downloaded from Elcodis.com electronic components distributor

METER BUTTONS
T-RST button - Clears the tare value.
£/MAX button - In the run mode, press the £/MAX button to show the
maximum value if jumper S3 is installed: the meter momentarily shows
“####”, then flashes the maximum value encountered since the last peak
reset. Press the £/MAX button to show the VALLEY value if jumper S3 is
removed: the meter momentarily shows “™™™™”, then flashes the minimum
value encountered since the last valley reset. In the configuration mode, press
the £/MAX button to change the flashing digit’s value (increments by one).
£/TARE button - In the run mode, press the £/TARE button to tare the
display value to zero. In the configuration mode, press the £/TARE button to
scroll through available choices, or to move one digit to the right.
MENU button - In the run mode, press the MENU button to enable meter
configuration changes. Refer to specific procedure for more details.
RESET button - In the run mode, press the RESET button to reset the Peak
and Valley registers: the meter momentarily shows “PrSt” or “VrSt” , then
resets both values. In the configuration mode, press the RESET button twice
quickly to escape from the configuration mode.
4
Downloaded from Elcodis.com electronic components distributor

2.2 BACK OF THE METER
Figure - shows the connectors on the back of the meter. Table -1 gives a
brief description of each connector at the back of the meter. Refer to Figure -3
for dc-power connection information.
Figure 2-2. Connectors for ac-Power (Top) and dc-Power (Bottom)
Table 2-1. Connector Description
Connector Description
J1-1 ac line connection (No Connection on dc-powered units).
J1- ac neutral connection (+ input on dc-powered units).
J1-3 ac earth ground (dc-power return on dc-powered units).
J -1 Remote tare connection with momentary switch to J - .
J - Digital Return (RTN).
J -3 Tare reset with momentary switch to J - .
J3-1 Hold input (active low) - Connect to J - to hold meter reading
(does not update Min/Max).
J3- +EXC: Positive excitation connection from meter (10, 4 Vdc).
J3-3 -EXC: Negative excitation connection from meter (10, 4 Vdc).
J4-1 Analog Input return (RTN).
J4- Analog Current input (4- 0 mA).
J4-3 Analog Voltage input (0-5 V, 0-10 V etc.).
5
Downloaded from Elcodis.com electronic components distributor

2.2 BACK OF THE METER (Continued)
Figure 2-3. dc-Power Connections
2.3 DISASSEMBLY
You may need to open up the meter for one of the following reasons:
* To check or change the 115 or 30 Vac power jumpers.
* To install or remove calibration jumper on the main board.
Disconnect the power supply before proceedings.
To remove and access the main board, follow these steps:
1. Disconnect the main power from the meter.
. Remove the front lens.
3. Pull the meter forward, out of its case.
6
Downloaded from Elcodis.com electronic components distributor

SECTION 3. GETTING STARTED
CAUTION: The meter has no power-on switch, so it will be in
operation as soon you apply power.
If you power off/on the meter momentarily shows the following: “idP” for
model type, “codE” , and “rxx” for the micro controller revision code.
Keep track of revision code for future reference.
3.1 CHANGING CONFIGURATION JUMPERS
The S1, S and S3 DIP switches are at the front of the meter near the digital
display. The S4 DIP switch is on side of the main board (refer to
Figure 3–3). Remove the lens cover to access these jumpers.
Table 3-1. S1 - S4 DIP Switches (Defaults in bold and italics)
Jumper Description
S1 Installed: 10 volt excitation
Removed: 24 volt excitation
S Installed: Front-panel buttons locked out
Removed: All buttons operable
S3 Installed: PEAK shows when £/MAX button is pushed
Removed: VALLEY shows when £/MAX button is
pushed
S4 Installed: Calibration enabled
Removed: Calibration disabled
7
Downloaded from Elcodis.com electronic components distributor

3.1 CHANGING CONFIGURATION JUMPERS (Continued)
Front of the meter
Figure 3-1. S1 - S4 Jumpers
3.2 MOUNTING THE METER
Figure 3-2. Meter - Exploded View
PANEL CUTOUT
8
Downloaded from Elcodis.com electronic components distributor

3.2 MOUNTING THE METER (Continued)
1. Cut a hole in your panel according to
the dimensions specified in Figure 3-3.
. Insert the meter into the hole. Be sure
the front bezel is flush to the panel.
Figure 3-3. Panel Cut-Out
3. Proceed to Section 3.4 to connect your sensor input.
3.3 CONNECTING SENSOR INPUT
Figures 3-4 through 3-8 describe how to connect common sensor types.
Figure 3-4. 3-Wire dc Voltage Input Connection
with Internal Excitation
J2
1
2
3
J3
1
2
3
J4
1
2
3
RTN
I
V
HOLD
EXC
EXC
EXC
COM
SIG 0 10Vdc
9
45,00 + 0,61/-0,00
(1.772 + .024/–.000)
92,00 + 0,81/–0,00
(3.622 + .032/–.000)
PANEL THICKNESS
1,5
R(.06)
4 PLCS
6,4 (.25) MAX
0,8 (.03) MIN
NOTE: Dimensions in Millimeters (Inches)
Downloaded from Elcodis.com electronic components distributor

3.3 CONNECTING SENSOR INPUT (Continued)
Figure 3-5. 2-Wire dc Voltage Input Connections
with External Excitation
Figure 3-6. 4-20 mA Input Connections
with External Excitation
J2
1
2
3
J3
1
2
3
J4
1
2
3
RTN
I
V
EXTERNAL SUPPLY
J2
1
2
3
J3
1
2
3
J4
1
2
3
RTN
I
V
SIG
HI
SIG
LOW
SOURCE
0 10Vdc
10
Downloaded from Elcodis.com electronic components distributor

3.3 CONNECTING SENSOR INPUT (Continued)
Figure 3-7. 4-20 mA Transmitter Hook-Up
with Internal Excitation
Figure 3-8. dc Current Input Connections with Current Source
J2
1
2
3
J3
1
2
3
J4
1
2
3
RTN
I
V
J2
1
2
3
J3
1
2
3
J4
1
2
3
RTN
I
V
HOLD
EXC
EXC
11
Downloaded from Elcodis.com electronic components distributor

3.4 CONNECTING MAIN POWER
Connect the ac main power connections as shown in Figure 3-9.
WARNING: Do not connect ac power to your meter until you have complet-
ed all input and output connections. Failure to do so may result in injury!
Figure 3-9. Main Power Connections - ac
Table 3- shows the wire color and respective terminal connections for both
USA and Europe. Table 3- . ac-Power Connections
Connect the dc main power connection a hown in Figure 3-10.
Figure 3-10. Main Power Connections - DC
+ DC - DC
DC POWER
123
J1
WIRE COLORS
J1 AC POWER EUROPE USA
1~ac Line Brown Black
2~ac Neutral Blue White
3~ac Earth Ground Green/Yellow Green
Line Neutral
AC Power
123
FUSE
Earth
Ground
J1
1
Downloaded from Elcodis.com electronic components distributor

SECTION 4. CONFIGURING THE METER
4.1 SELECTING THE INPUT RANGE (INPT)
Refer to Table -2 for a summary list of menu configuration.
To select your appropriate input range, follow these steps:
1. Press the MENU button. The meter flashes “InP”.
. Press the ¢/TARE button. The meter flashes one of the following:
* 0 - 10 (for 0-10 volt)
* 4 - 0 (for 4- 0 mA)
* 0 - 4 (for 0-4 mA)
* 0 - 5 (for 0-5 volt)
* 1 - 5 (for 1-5 volt)
3. Press the ¢/TARE button to scroll through available choices.
4. Press the MENU button to store your choice. The meter momentarily
shows “StOr”, followed by “dEc.P” (Decimal point).
13
Downloaded from Elcodis.com electronic components distributor

4.2 SELECTING A DECIMAL POINT POSITION (DEC.P)
Refer to Table -2 for a summary list of menu configuration.
To select a decimal point display position, follow these steps:
1. Press the MENU button until the meter shows “dEc.P”.
. Press the ¢/TARE button. The meter shows one of the following:
* FFF.F
* FFFF.
* FFFF
* F.FFF
* FF.FF
3. Press the ¢/TARE button to move the decimal point to the right one
position.
4. Press the MENU button to store your choice. The meter momentarily
shows “Stor”, followed by “ScAL” (Scaling).
4.3 SCALING THE METER
There are two scaling methods. One method is internal scaling, “int” (scaling
without known loads): you decide upon low and high reading values and
manually enter them through the keyboard. The meter then operates with those
new parameters. Another method is live scaling, “LivE” : you apply low and
high input signals and change the meter reading accordingly. The meter
calculates a new scale factor and then operates with those new parameters.
14
Downloaded from Elcodis.com electronic components distributor